Home » Dymo Manuals » Label Makers » Dymo Rhino 6000 Industrial Label Printer » Manual Viewer

Dymo Rhino 6000 Industrial Label Printer Quick Start Guide - Page 3

Quick Start Guide - rhino

View all Dymo Rhino 6000 Industrial Label Printer manuals

Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

English Quick Start Guide Follow these steps to install your RHINO 6000 label printer and software, and print your first label. 1. Unpacking your printer NOTE Do not plug the printer into your computer until asked to do so during the software installation. 1. Unpack your label printer and save the packing materials. 2. Make sure you have all the items shown in Figure 1. Quick Start and Quick Reference Guides USB cable Two RHINO label cassettes Power adapter CD-ROM Battery pack RHINO 6000 label printer Figure 1 1

Section	Page
1. Unpacking your printer	3
1. Unpack your label printer and save the packing materials.	3
2. Make sure you have all the items shown in Figure 1.	3
Figure 1	3
2. Connecting the power	4
Figure 2	4
To insert the battery pack	4
1. Remove the battery compartment cover. See Figure 2.	4
2. Insert the battery pack into the battery compartment.	4
3. Replace the battery compartment cover.	4
Figure 3	4
To connect the power adapter	4
1. Plug the power adapter into the power connector on the bottom of the printer. See Figure 3.	4
2. Plug the other end of the power adapter into a power outlet.	4
3. Inserting the label cassette	5
To insert the label cassette	5
1. Lift the label cassette cover to open the label compartment. See Figure 4.	5
Figure 4	5
2. Make sure the label and ribbon are taut across the mouth of the cassette and that the label passes between the guideposts. If necessary, turn the spool clockwise to tighten the ribbon.	5
3. Insert the cassette and press gently until the cassette is eased into place.	5
4. Make sure the two blue clips lock the cassette in place. Refer to the label on the cassette.	5
5. Close the label cassette cover.	5
To remove the label cassette	5
1. Lift the label cassette cover to open the label cassette compartment.	5
2. Press the Eject button. The label cassette is automatically lifted.	5
3. Replace the cassette as described above.	5
4. Connecting the printer to your computer	6
To connect the printer to your computer	6
Figure 5	6
1. Plug the USB cable into the USB port on the bottom of the printer. See Figure 5.	6
2. Plug the USB cable into a USB port ONLY when prompted during the software installation.	6
5. Installing the Software	6
To install the software	6
1. Insert the RHINO Connect Software CD into your CD-ROM drive. After a few seconds, the installation screen appears. If the installation screen does not appear:	6
a. Click Start and then Run on the Windows taskbar. The Run dialog box appears.	6
b. Enter D:\\setup.exe (where D is the CD-ROM drive letter) and click OK.	6
2. Follow the on-screen instructions.	6
3. When prompted by the installer, plug the USB cable into a USB port.	6
6. Printing your first label with the printer	7
To print your first label	7
1. Press to turn on the power.	7
2. Use the up and down arrow keys to select the language you wish to use and press OK.	7
3. Use the up and down arrow keys to select the units of measure you wish to use and press OK.	7
4. Select the tape width of the tape cassette currently inserted in the printer and press OK.	7
5. Enter some text for your label using the alphanumeric keys.	7
6. Press PRINT.	7
7. Press CUT and remove the label.	7
7. Using RHINO Connect Software	8