Epson Expression 10000XL - Photo User Manual - Page 63

Network Image Express Interface Card, Setting Up Client Computers, Installing the Card in Your Scanner

Get Epson Expression 10000XL - Photo PDF manuals and user guides View all Epson Expression 10000XL - Photo manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Network Image Express Interface Card This section explains how to install the optional Network Image Express interface card (B12B808393) in your scanner. Setting Up Client Computers Before connecting the scanner to your network, make sure any computer you want to use for scanning is set up properly. Check that: ■ an Ethernet network card is installed in the computer ■ the computer is configured to use the TCP/IP network protocol ■ your scanner software is installed (see the Start Here sheet for instructions) For instructions on installing your computer's card, see the manual that came with the card. For instructions on setting up TCP/IP, see the Expression 10000XL Reference Guide on your computer. Installing the Card in Your Scanner 1. Turn off the scanner and disconnect the power cord and any cables. 2. Remove the two screws securing the shield plate to the scanner's optional interface slot, and then remove the plate. Keep the screws and shield plate in case you want to reinstall them later. 3. Fully insert the Network Image Express card in the slot, and tighten its screws. Caution: Do not insert the card with the scanner turned on, or you could damage the card or the scanner. Using Optional Equipment 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Using Optional Equipment
63
Network Image Express Interface Card
This section explains how to install the optional Network Image Express interface
card (B12B808393) in your scanner.
Setting Up Client Computers
Before connecting the scanner to your network, make sure any computer you want to
use for scanning is set up properly. Check that:
■
an Ethernet network card is installed in the computer
■
the computer is configured to use the TCP/IP network protocol
■
your scanner software is installed (see the
Start Here
sheet for instructions)
For instructions on installing your computer’s card, see the manual that came with
the card. For instructions on setting up TCP/IP, see the
Expression 10000XL
Reference Guide
on your computer.
Installing the Card in Your Scanner
1.
Turn off the scanner and disconnect the power cord and any cables.
2.
Remove the two screws securing the shield plate to the scanner’s optional interface
slot, and then remove the plate. Keep the screws and shield plate in case you want
to reinstall them later.
3.
Fully insert the Network Image Express card in the slot, and tighten its screws.
Caution:
Do not insert the card with the scanner turned on, or you could damage
the card or the scanner.