Fisher and Paykel WA3927G1 User Guide - Page 12

Drain hose, Inlet hoses, Inlet hose replacement

Get Fisher and Paykel WA3927G1 PDF manuals and user guides View all Fisher and Paykel WA3927G1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

US 10 Installation instructions CA Drain hose Standpipe 33 ½" to 95" (850 - 2400 mm) 1 Carefully pull the drain hose out from the back of the washer by pulling the exposed part of the hose downwards and outwards. Pull hose 2 To guide the drain hose over the tub/sink or through guide standpipe the hose guide MUST be fitted to the drain hose. Important! To prevent siphoning the drain hose should not extend more than ¾" (20 mm) from the end of the guide. The height of the standpipe or tub/sink should be between 33 ½" to 95" (850 - 2413 mm). The drain hose can be trimmed to length. Flex hose guide apart ¾" (20 mm) maximum 3 Place the drain hose in the tub/sink or standpipe. Do not fit the hose to a drain spigot. Drainage must not be airtight in order to prevent siphoning. Fig.4 Fitting the drain hose guide Important! ■■ In multi-story apartments or any upper floor installation, the washer should be installed on a floor that is equipped with a drain. ■■ Check that the tub or standpipe is free from lint or other obstructions before operating the washer. ■■ In a basement installation do not exceed a standpipe height of 96" (2438 mm). Inlet hoses Important! ■■ New hose sets provided with the washer shall be used to connect the washer to the water mains. ■■ Old hose sets should not be re-used. 1 Install hoses with the straight end (with filters) fitted to the faucets (refer to Fig.5). 2 Install elbow ends of hoses onto clothes washer inlet valves (refer to Fig.6). The valves are marked on the back of the washer (H=hot, C=cold). Ensure the hot valve is connected to the hot faucet and the cold valve is connected to the cold faucet. Fig.5 Faucet end of Fig.6 Washer end of hose (straight end) hose (elbow end) Inlet hose replacement Important! The inlet hoses should be replaced every 5 years. Hoses should be checked from time to time and replaced if any wear, cuts, bulges, kinks or leaks are found. WARNING!: Failure to do so may result in a flood and damage to property.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
10
Installation instructions
US
CA
Drain hose
1
Carefully pull the drain hose out from the back of
the washer by pulling the exposed part of the hose
downwards and outwards.
2
To guide the drain hose over the tub/sink or
standpipe the hose guide MUST be fitted to the
drain hose.
Important!
To prevent siphoning the drain hose should not
extend more than ¾” (20 mm) from the end of the
guide. The height of the standpipe or tub/sink should
be between 33 ½” to 95” (850 – 2413 mm).
The drain hose can be trimmed to length.
3
Place the drain hose in the tub/sink or standpipe. Do
not fit the hose to a drain spigot. Drainage must not
be airtight in order to prevent siphoning.
Important!
■
±
In multi-story apartments or any upper floor installation, the washer should be installed on a
floor that is equipped with a drain.
■
±
Check that the tub or standpipe is free from lint or other obstructions before operating the washer.
■
±
In a basement installation do not exceed a standpipe height of 96” (2438 mm).
Inlet hoses
Important!
■
±
New hose sets provided with the washer shall be used
to connect the washer to the water mains.
■
±
Old hose sets should not be re-used.
1
Install hoses with the straight end (with filters) fitted
to the faucets (refer to Fig.5).
2
Install elbow ends of hoses onto clothes washer inlet
valves (refer to Fig.6). The valves are marked on the
back of the washer (H=hot, C=cold). Ensure the hot
valve is connected to the hot faucet and the cold
valve is connected to the cold faucet.
Inlet hose replacement
Important!
The inlet hoses should be replaced every 5 years. Hoses should be checked from time to time and
replaced if any wear, cuts, bulges, kinks or leaks are found. WARNING!: Failure to do so may result
in a flood and damage to property.
Fig.6 Washer end of
hose (elbow end)
Fig.5 Faucet end of
hose (straight end)
Fig.4 Fitting the drain hose guide
Flex hose
guide apart
Standpipe 33 ½” to 95”
(850 – 2400 mm)
°” (20 mm)
maximum
Pull hose
through guide