Fisher and Paykel WA3927G1 User Guide - Page 13

Leveling instructions

Get Fisher and Paykel WA3927G1 PDF manuals and user guides View all Fisher and Paykel WA3927G1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Installation instructions 11 US CA Leveling instructions It is IMPORTANT to level the machine to ensure good spin performance and effective detergent and fabric softener dispensing. A spirit level is provided with your machine. Use this to level your machine, placing it bottom side down in the locations specified below (ensure the surfaces are clean). The machine is level when the bubble sits in the center, within the two lines. Your washer is equipped with self-locking feet to ensure they do not move once you have leveled your machine. To adjust the feet, tip the washer back or forward to locate the foot you wish to adjust, pull down gently and then twist to move it up or down to the required level. Repeat if necessary. Important! After leveling, the corners of the washer should be clear of the floor (by at least 2/5" (10 mm) and the machine must not rock in any direction. 1 If not already installed, fit the rubber inserts into all 4 feet on the base of the machine. 2 Extend all 4 feet by three full turns before moving the machine to its final position. 3 Move the machine to its final position using the top corners to manoeuvre the product into place (do not push against the center front of the machine). We recommend a minimum clearance of 3/4" (20 mm) each side and 2" (50 mm) at the rear of the machine. 4 With the lid closed, place the spirit level at the center back of the lid (near the control panel). If not level, pull the machine out and adjust the rear feet until the machine is level side to side when in position. 5 Open the lid. Place spirit level on the flat surface on the left side, inline with the center of the basket. If necessary, adjust the front left foot until the machine is level. Adjustable feet Rubber insert Fig.7 Leveling - Step 1 & 2 Spirit level Fig.8 Leveling - Step 4 Spirit level Fig.9 Leveling - Step 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
11
Installation instructions
US
CA
Leveling instructions
It is IMPORTANT to level the machine to ensure good spin performance and effective detergent
and fabric softener dispensing.
A spirit level is provided with your machine. Use this to level your machine, placing it bottom
side down in the locations specified below (ensure the surfaces are clean). The machine is level
when the bubble sits in the center, within the two lines.
Your washer is equipped with self-locking feet to ensure they do not move once you have
leveled your machine. To adjust the feet, tip the washer back or forward to locate the foot you
wish to adjust, pull down gently and then twist to move it up or down to the required level.
Repeat if necessary.
Important!
After leveling, the corners of the washer
should be clear of the floor (by at least
±²³” (10 mm) and the machine must not
rock in any direction.
1
If not already installed, fit the rubber
inserts into all 4 feet on the base of the
machine.
2
Extend all 4 feet by three full turns before
moving the machine to its final position.
3
Move the machine to its final position
using the top corners to manoeuvre the
product into place (do not push against
the center front of the machine). We
recommend a minimum clearance of
°” (20 mm) each side and 2” (50 mm) at
the rear of the machine.
4
With the lid closed, place the spirit
level at the center back of the lid (near
the control panel). If not level, pull the
machine out and adjust the rear feet
until the machine is level side to side
when in position.
5
Open the lid. Place spirit level on the
flat surface on the left side, inline with
the center of the basket. If necessary,
adjust the front left foot until the
machine is level.
Adjustable feet
Rubber insert
Fig.7 Leveling – Step 1 & 2
Fig.8 Leveling – Step 4
Spirit level
Fig.9 Leveling – Step 5
Spirit level