Fujitsu MBA3073NC Product Manual - Page 80

CN2 setting terminal on NP models only, SCSI ID setting, IMPORTANT

Get Fujitsu MBA3073NC - Enterprise 73.5 GB Hard Drive PDF manuals and user guides View all Fujitsu MBA3073NC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

2 4 6 8 10 12 14 16 18 20 22 24 1 3 5 7 9 11 13 15 17 19 21 23 Terminator power supply: Supply (LED signal) (HDD Reset signal) N.C. Force Single Ended: LVD mode Force Narrow: 16-bit SCSI Motor start mode Write protect: enabled SCSI ID #15 Figure 5.3 CN2 setting terminal (on NP models only) 5.3.1 SCSI ID setting Table 5.1 shows the SCSI ID setting. For the terminal location and allocation of NC model, see Figure 4.13 and Table B.1. For NP model, see Figure 5.2 and 5.3. IMPORTANT When the SCSI ID is set using the external operator panel connector CN1 of NP model, all pins listed in Table 5.1 should be open. If any of pins are shorted, unexpected SCSI ID is set. 76 Downloaded from www.Manualslib.com manuals search engine C141-E270

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
24
22
20
18
16
14
12
10
8
6
4
2
21
19
17
15
13
11
9
7
5
3
1
Terminator power supply:
Supply
(LED signal)
(HDD Reset signal)
23
N.C.
Force Single Ended:
LVD mode
Force Narrow:
16-bit SCSI
Motor start mode
Write protect:
enabled
SCSI ID
#15
Figure 5.3
CN2 setting terminal (on NP models only)
5.3.1
SCSI ID setting
Table 5.1 shows the SCSI ID setting.
For the terminal location and allocation of NC model, see
Figure 4.13 and Table B.1.
For NP model, see Figure 5.2 and 5.3.
IMPORTANT
When the SCSI ID is set using the external operator panel connector
CN1 of NP model, all pins listed in Table 5.1 should be open.
If any
of pins are shorted, unexpected SCSI ID is set.
76
C141-E270
Downloaded from
www.Manualslib.com
manuals search engine