Garmin Edge 520 Plus Owners Manual - Page 22

2 From your compatible Garmin watch, select Settings > Sensors & Accessories > Add New > Extended Display. 3 Follow the on-screen instructions on your Edge device and Garmin watch to complete the pairing process. The data screens from your paired watch appear on the Edge device when the devices are paired. NOTE: Normal Edge device functions are disabled while using Extended Display mode. After pairing your compatible Garmin watch with your Edge device, they connect automatically the next time you use Extended Display mode. Exiting Extended Display Mode While the device is in Extended Display mode, select > Exit Extended Display Mode > OK. Device Information Specifications Edge Specifications Battery type Rechargeable, built-in lithium-ion battery Battery life Up to 15 hr. Operating temperature range From -20º to 60ºC (from -4º to 140ºF) Charging temperature range From 0º to 45ºC (from 32º to 113ºF) Wireless frequency/protocol 2.4 GHz @ 0 dBm nominal Water rating IEC 60529 IPX71 Heart Rate Monitor Specifications Battery type User-replaceable CR2032, 3 V Battery life Water resistance Up to 4.5 yr. at 1 hr./day 3 ATM2 NOTE: This product does not transmit heart rate data while swimming. Operating temperature From -5° to 50°C (from 23° to 122°F) range Wireless frequency/ protocol 2.4 GHz ANT+ wireless communications protocol Cleaning the Device 1 Wipe the device using a cloth dampened with a mild detergent solution. 2 Wipe it dry. After cleaning, allow the device to dry completely. Caring for the Heart Rate Monitor NOTICE You must unsnap and remove the module before washing the strap. A build up of sweat and salt on the strap can decrease the ability of the heart rate monitor to report accurate data. • Go to www.garmin.com/HRMcare for detailed washing instructions. • Rinse the strap after every use. • Machine wash the strap after every seven uses. • Do not put the strap in a dryer. • When drying the strap, hang it up or lay it flat. • To prolong the life of your heart rate monitor, unsnap the module when not in use. User Replaceable Batteries WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. Replacing the Heart Rate Monitor Battery 1 Use a small Phillips screwdriver to remove the four screws on the back of the module. 2 Remove the cover and battery. Speed Sensor and Cadence Sensor Specifications Battery type Battery life Operating temperature range User-replaceable CR2032, 3 V Approximately 12 months (1 hour per day) From -20º to 60ºC (from -4º to 140ºF) Wireless frequency/ protocol Water rating 2.4 GHz ANT+ wireless communications protocol 1 ATM3 Device Care NOTICE Do not store the device where prolonged exposure to extreme temperatures can occur, because it can cause permanent damage. Avoid chemical cleaners, solvents, and insect repellents that can damage plastic components and finishes. Secure the weather cap tightly to prevent damage to the USB port. 3 Wait 30 seconds. 4 Insert the new battery with the positive side facing up. NOTE: Do not damage or lose the O-ring gasket. 5 Replace the back cover and the four screws. NOTE: Do not overtighten. After you replace the heart rate monitor battery, you may need to pair it with the device again. Replacing the Speed Sensor or Cadence Sensor Battery The LED flashes red to indicate a low battery level after two revolutions. 1 Locate the circular battery cover on the back of the sensor. 1 The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating. 2 The device withstands pressure equivalent to a depth of 30 m. For more information, go to www.garmin.com/waterrating. 3 The device withstands pressure equivalent to a depth of 10 m. For more information, go to www.garmin.com/waterrating. 18 2 Twist the cover counter-clockwise until the marker points to unlocked and the cover is loose enough to remove. Device Information