Gateway 995 995 Series Server User Guide - Page 90

Replacing a standard expansion card, To replace an expansion card

Get Gateway 995 PDF manuals and user guides View all Gateway 995 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Chapter 4: Installing Components 7 From the back of the server, press the card's locking clip in until it clicks into place. 8 Reinstall the top rear panel. Replacing a standard expansion card The server must be off when you install expansion cards into PCI card slots 1 through 4. Warning Standard expansion cards cannot be replaced while the server is on. To replace an expansion card: 1 Follow the instructions in "Preventing static electricity discharge" on page 36. Make sure that you turn off the server, then unplug the power cords and all other cables connected to the server. 2 Remove the inside panel. For instructions, see "Removing the inside panel" on page 45. 3 Disconnect any cables attached to the card. 4 Press down on the expansion card's locking clip, then rotate the clip up and out of the way. 84 www.gateway.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
84
Chapter 4: Installing Components
www.gateway.com
7
From the back of the server, press the card’s locking clip in until it clicks
into place.
8
Reinstall the top rear panel.
Replacing a standard expansion card
The server must be off when you install expansion cards into PCI card slots
1 through 4.
To replace an expansion card:
1
Follow the instructions in
“Preventing static electricity discharge” on
page 36
. Make sure that you turn off the server, then unplug the power
cords and all other cables connected to the server.
2
Remove the inside panel. For instructions, see
“Removing the inside panel”
on page 45
.
3
Disconnect any cables attached to the card.
4
Press down on the expansion card’s locking clip, then rotate the clip up
and out of the way.
Warning
Standard expansion cards cannot be replaced while the
server is on.