GE DCVH485EKMS Use and Care Manual - Page 16

Installation Instructions, CONNECTING AN ELECTRIC DRYER cont., WARNING

Get GE DCVH485EKMS PDF manuals and user guides
UPC - 084691191261
View all GE DCVH485EKMS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Installation Instructions CONNECTING AN ELECTRIC DRYER (cont.) CONNECTING DRYER USING 3-WIRE CONNECTION Ground strap Bracket 1. Turn off the circuit breaker(s) (30 amp) or remove the dryer's circuit fuse at the electrical box. 2. Be sure the dryer cord is unplugged from the wall receptacle. 3. Remove the power cord cover located at the upper back. 4. Bring the power cord through the bracket. 5. Connect power cord as follows: A. Connect the 2 hot lines to the outer screws of the terminal block (marked L1 and L2). B. Connect the neutral (white) line to the center of the terminal block (marked N). 6. Be sure ground strap is connected to green ground screw on cabinet rear. Tighten all terminal block screws (3) completely. 7. Reinstall the cover. WARNING - NEVER LEAVE THE COVER OFF OF THE TERMINAL BLOCK. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Installation Instructions
16
CONNECTING AN ELECTRIC DRYER (cont.)
CONNECTING DRYER USING 3-WIRE
CONNECTION
1.
Turn off the circuit breaker(s) (30 amp) or remove
the dryer’s circuit fuse at the electrical box.
2.
Be sure the dryer cord is unplugged from the
wall receptacle.
3.
Remove the power cord cover located at the
upper back.
4.
Bring the power cord through the bracket.
5.
Connect power cord as follows:
A.
Connect the 2 hot lines to the outer screws
of the terminal block (marked L1 and L2).
B.
Connect the neutral (white) line to the center
of the terminal block (marked N).
6.
Be sure ground strap is connected to green
ground screw on cabinet rear. Tighten all
terminal block screws (3) completely.
7.
Reinstall the cover.
WARNING –
NEVER LEAVE THE
COVER OFF OF THE TERMINAL BLOCK.
Ground strap
Bracket