GE DPVH880EJWW Owners Manual - Page 25

Example Only

Get GE DPVH880EJWW - Profile - Dryer PDF manuals and user guides
UPC - 084691169840
View all GE DPVH880EJWW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Installation Instructions WARNING USE ONLY METAL DUCT 4″ DIAMETER (102 mm FOR CANADA). DO NOT USE DUCT LONGER THAN SPECIFIED IN THE EXHAUST LENGTH TABLE. Ducting longer than 150 equivalent feet will: • Increase the drying times and the energy cost. • Reduce the dryer life. • Accumulate lint, creating a potential fire hazard. • Total length of flexible metal duct shall not exceed 7.9′ (2.4 m). EXAMPLE ONLY The following chart describes an example of one possible ductwork installation. The correct exhaust installation is your responsibility. Problems due to incorrect installation are not covered by the warranty. The length of the exhaust system depends upon the type of duct, number of turns and the type of exhaust hood (wall cap), and all conditions noted below. For satisfactory air movement, the total duct length should not exceed 150 equivalent feet. DUCT PIECES EQUIVALENT RIGID NUMBER EQUIVALENT LENGTH X USED = LENGTH Rigid Metal 1 Ft. X (4) = 4 Ft. Ducting (Preferred) TRANSITION DUCTING (DRYER TO WALL) INSIDE WALLS/CEILING (WALL TO WALL CAP) Elbows (90°/45°) 10 Ft. X (3) = Less Than 4 Ft. Turns Less Than 4 Ft. 2 Ft. X (1) = Rigid Ducting 1 Ft. X (5) = 4″ Wall Cap 5 Ft. X (1) = 4≤ (10.2 cm) Total Ductwork Length = TOTAL MUST BE LESS THAN OR EQUAL TO 150 FT. 25 30 Ft. 2 Ft. 5 Ft. 5 Ft. 46 Ft. WALL CAPS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
EQUIVALENT
RIGID
NUMBER
EQUIVALENT
DUCT PIECES
LENGTH
X
USED
=
LENGTH
Rigid Metal
1 Ft.
X
(4)
=
4 Ft.
Ducting
(Preferred)
Elbows
10 Ft.
X
(3)
=
30 Ft.
(90°/45°)
Turns Less
2 Ft.
X
(1)
=
2 Ft.
Than 4 Ft.
Rigid Ducting
1 Ft.
X
(5)
=
5 Ft.
4
″
Wall Cap
5 Ft.
X
(1)
=
5 Ft.
Total Ductwork Length
=
46 Ft.
TOTAL MUST BE LESS THAN OR EQUAL TO 150 FT.
Installation Instructions
25
WARNING
USE ONLY METAL DUCT 4
″
DIAMETER (102 mm
FOR CANADA). DO NOT USE DUCT LONGER THAN
SPECIFIED IN THE EXHAUST LENGTH TABLE.
Ducting longer than 150 equivalent feet will:
•
Increase the drying times and the energy cost.
•
Reduce the dryer life.
•
Accumulate lint, creating a potential fire hazard.
•
Total length of flexible metal duct shall not exceed
7.9
′
(2.4 m).
EXAMPLE ONLY
The following chart describes an example of one
possible ductwork installation.
The correct exhaust installation is your
responsibility.
Problems due to incorrect installation are not
covered by the warranty.
The length of the exhaust system depends upon
the type of duct, number of turns and the type of
exhaust hood (wall cap), and all conditions noted
below.
For satisfactory air movement, the total duct length
should not exceed
150
equivalent feet.
4≤
(10.2 cm)
TRANSITION
DUCTING
(DRYER TO WALL)
INSIDE WALLS/CEILING
(WALL TO WALL CAP)
WALL
CAPS
Less Than 4 Ft.