Gigabyte GA-Z87X-UD7 TH User Manual - Page 77

Configuring Marvell® 88SE9230 SATA Controller, 88SE9230 SATA Controller

Get Gigabyte GA-Z87X-UD7 TH PDF manuals and user guides View all Gigabyte GA-Z87X-UD7 TH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

3-2 Configuring Marvell® 88SE9230 SATA Controller A. Installing SATA hard drive(s) in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port on the motherboard. The Marvell® 88SE9230 SATA controller controls the onboard GSATA3 6/7/8/9 connectors. Then connect the power connector from your power supply to the hard drive. B. Configuring SATA controller and RAID mode in BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup. Step: Turn on your computer and press to enter BIOS Setup during the POST. To create RAID, go to Peripherals\Marvell SATA Controller Configuration and make sure GSATA Controller is set to AHCI Mode. Press on GSATA RAID Configuration to enter the RAID configuration screen. Figure 1 The BIOS Setup menus described in this section may differ from the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version. - 77 - Configuring SATA Hard Drive(s)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
- 77 -
Configuring SATA Hard Drive(s)
3-2
Configuring Marvell
®
88SE9230 SATA Controller
A. Installing SATA hard drive(s) in your computer
Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available
SATA port on the motherboard. The Marvell
®
88SE9230 SATA controller controls the onboard GSATA3 6/7/8/9
connectors. Then connect the power connector from your power supply to the hard drive.
B. Configuring SATA controller and RAID mode in BIOS Setup
Make sure to configure the SATA controller mode correctly in system BIOS Setup.
Step:
Turn on your computer and press <Delete> to enter BIOS Setup during the POST. To create RAID, go to
Peripherals\Marvell SATA Controller Configuration
and make sure
GSATA Controller
is set to
AHCI Mode
.
Press <Enter> on
GSATA RAID Configuration
to enter the RAID configuration screen.
Figure 1
The BIOS Setup menus described in this section may differ from the exact settings for your motherboard.
The actual BIOS Setup menu options you will see shall depend on the motherboard you have and
the BIOS version.