Graco 8F43PTI3 Owners Manual - Page 31

To Install Locking Clip: DO NOT use with base, Combination Lap/Shoulder, Belt with Sliding Latch,

Get Graco 8F43PTI3 - SnugRide Infant Car Seat PDF manuals and user guides
UPC - 047406102723
View all Graco 8F43PTI3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

• Combination Lap/Shoulder This belt has a latch plate that slides Belt with Sliding Latch freely along the belt. Plate This belt MUST be converted to prevent movement of the lap portion of the belt. You must use a locking clip (provided with the infant restraint) when using the infant restraint without the base unless your vehicle's seat belt can be Locking clip converted in another way as described in your vehicle owner's manual. To Install Locking Clip: (DO NOT use with base) 1. Tighten the buckled belt by pushing down hard on the infant restraint and pulling hard 1/2 inch (1 cm) on the shoulder belt. 2. While pushing down on infant restraint, pinch – the two straps together behind the buckle tongue. Unbuckle the belt without allowing it to slip. — 3. Connect lap and shoulder belts with locking clip as shown – and —. 4. Rebuckle belt. Check that lap belt does not move by pulling and pushing hard on infant restraint. If belt loosens or lengthens, repeat procedure. Locking clip goes here, 1/2 inch (1 cm) from the buckle 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
31
To Install Locking Clip: (DO NOT use with base)
1.
Tighten the buckled belt by pushing down
hard on the infant restraint and pulling hard
on the shoulder belt.
2.
While pushing down on infant restraint, pinch
the two straps together behind the buckle
tongue. Unbuckle the belt
without allowing it to slip.
3.
Connect lap and shoulder belts
with locking clip as shown
➊
and
➋
.
4.
Rebuckle belt. Check that lap belt
does not move by pulling and
pushing hard on infant restraint.
If belt loosens or lengthens,
repeat procedure.
Locking clip
Locking clip goes here,
1
/
2
inch (1 cm) from the buckle
➋
•
Combination Lap/Shoulder
Belt with Sliding Latch
Plate
This belt has a latch plate that slides
freely along the belt.
This belt
MUST
be converted to prevent
movement of the lap portion of the belt.
You must use a
locking clip
(provided
with the infant restraint) when using the
infant restraint
without the base
unless
your vehicle's seat belt can be
converted in another way as described
in your vehicle owner's manual.
1
/
2
inch
(1 cm)
➊