Graco 8F43PTI3 Owners Manual - Page 37

Using LATCH to install Base

Get Graco 8F43PTI3 - SnugRide Infant Car Seat PDF manuals and user guides
UPC - 047406102723
View all Graco 8F43PTI3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

7.3 Using LATCH to install Base 1. For ease of installation, extend — LATCH to its maximum length and remove from storage bars. 2. Position base in vehicle seat as shown. 3. Make sure LATCH is through vehicle/LATCH belt path normally used for vehicle seat belt. —. ˜ Belt must lay flat and not be twisted. 4. Hook Connectors to vehicle lower anchors. Pull firmly on Connectors to be sure they are attached ˜. 5. Tighten LATCH by pushing down ™ hard on base and pulling the adjustment belt ™. 6. NEVER put two LATCH connectors on one vehicle LATCH anchor unless specifically allowed by the vehicle manufacturer š. š 7. Test infant restraint for secure installation as described in infant restraint „Final Safety Check‰ page 40. 8. Check that the LATCH stays tight and does not slip from the tightened position. If it does not stay tight, try another seating position or contact Graco at 1-800-345-4109. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
37
1.
For ease of installation, extend
LATCH
to its maximum length
and remove from storage bars.
2.
Position base in vehicle seat as
shown.
3.
Make sure
LATCH
is through
vehicle/LATCH belt path normally
used for vehicle seat belt.
➋
.
Belt must lay flat and not be twisted.
4.
Hook
Connectors
to vehicle lower
anchors. Pull firmly on
Connectors
to
be sure they are attached
➌
.
5.
Tighten
LATCH
by pushing down
hard on base and pulling the
adjustment belt
➍
.
6.
NEVER
put two
LATCH
connectors
on one vehicle
LATCH
anchor unless
specifically allowed by the vehicle
manufacturer
➎
.
7.
Test infant restraint for secure
installation as described in infant
restraint
„Final Safety Check‰ page 40
.
8.
Check that the
LATCH
stays tight
and does not slip from the tightened
position. If it does not stay tight, try another
seating position or contact Graco at 1-800-345-4109.
7.3 Using LATCH to install Base
➋
➍
➎
➌