Graco 8F43PTI3 Owners Manual - Page 34

Installing the Infant Restraint and Base, Using Vehicle Belt

Get Graco 8F43PTI3 - SnugRide Infant Car Seat PDF manuals and user guides
UPC - 047406102723
View all Graco 8F43PTI3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

3. Buckle the vehicle belt. Make sure the buckle tongue goes into the correct buckle –. The seat – belt should not be twisted or turned. 4. Tighten the vehicle seat belt. Refer to your vehicle ownerÊs manual and the instructions in „6.2.2 SAFE Vehicle Belt Systems‰, page 29-31, on tightening your vehicle belt when using the infant restraint without base. To create a secure installation, push down — hard with your free hand on the infant restraint — and pull and tighten the vehicle belt. 5. Test infant restraint for secure installation as described in infant restraint „Final Safety Check‰ page 40. 7.2 Installing the Infant Restraint and Base Using Vehicle Belt When using the base to install the infant restraint, the lock-off is ALWAYS used to secure both belts of the lap or lap/shoulder belt. 1. Place the base in a rear-facing position on a vehicle seat. Lock-off ˜ 2. Open the lock-off and route the vehicle belt through the belt path and over the lock-off. ˜ 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
7.2 Installing the Infant Restraint and Base
Using Vehicle Belt
34
3.
Buckle the vehicle belt. Make sure the buckle
tongue goes into the correct buckle
➊
.
The seat
belt should not be twisted or turned.
4.
Tighten the vehicle seat belt. Refer to your
vehicle ownerÊs manual and the instructions in
„6.2.2 SAFE Vehicle
Belt Systems‰
, page 29-31, on tightening your vehicle belt when
using the infant restraint without base.
To create a secure installation, push down
hard with your free hand on the infant
restraint
➋
and pull and tighten the
vehicle belt.
5.
Test infant restraint for secure installation
as described in infant restraint
„Final Safety
Check‰ page 40
.
➊
➋
When using the base to install the infant
restraint, the lock-off is
ALWAYS
used to
secure
both
belts of the lap or lap/shoulder
belt.
1.
Place the base in a rear-facing position
on a vehicle seat.
2.
Open the lock-off and route the vehicle
belt through the belt path and over the
lock-off.
➌
➌
Lock-off