Harman Kardon AVR45 Owners Manual - Page 21

of Dolby Pro Logic.

Get Harman Kardon AVR45 PDF manuals and user guides View all Harman Kardon AVR45 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

System Configuration 18 When LARGE is selected, a fullrange output will be sent to the front left and right outputs, and NO low-frequency signals will be sent to the subwoofer output. 5. When you have completed your selection for the front channel, press the Set button i ˜, and then press the ⁄/¤ buttons g on the remote or the Selector buttons ¸ on the front panel to change the display to CEN SPEAKER. 6. Press the Set button i ˜ again, and use the ⁄/¤ buttons g on the remote, or the Selector buttons ¸ on the front panel, to select the option that best describes your system based on the speaker definitions shown above. When CEN SP SMALL is selected, low-frequency center channel sounds will be sent to the subwoofer output only. Note that if you choose this option and there is no subwoofer connected, you will not hear any low-frequency sounds from the center channel speaker. When CEN SP LARGE is selected, a full-range output will be sent to the center speaker output, and NO center channel signal will be sent to the subwoofer output. When CEN SP NONE is selected, no signals will be sent to the center channel output. The receiver will operate in a "phantom" center channel mode and center channel information will be sent to the left and right front channel outputs. 7. When you have completed your selection for the center channel, press the Set button i ˜, and then press the ⁄/¤ buttons g on the remote or the Selector buttons ¸ on the front panel to change the display to SUR SPEAKER. 8. Press the Set button i ˜ again, and then use the ⁄/¤ buttons g on the remote or the Selector buttons ¸ on the front panel to select the option that best describes your system based on the speaker definitions shown above. When SUR SP SMALL is selected, low-frequency surround channel sounds will be sent to the subwoofer output only. Note that if you choose this option and there is no subwoofer connected, you will not hear any low-frequency sounds from the surround speaker. When SUR SP LARGE is selected, a full-range output will be sent to the surround channel outputs, and NO surround channel signals will be sent to the subwoofer output. When SUR SP NONE is selected, surround sound information will be split between the front left and front right outputs. Note that for optimal performance when no surround speakers are in use, the Dolby 3 Stereo mode should be used instead of Dolby Pro Logic. 9. When you have completed your selection for the surround channel, press the Set button i ˜, and then press the ⁄/¤ buttons g on the remote or the Selector buttons ¸ on the front panel to change the display to S W SPEAKER. 10. Press the Set button i ˜, and then press the ⁄/¤ buttons g on the remote or the Selector buttons ¸ on the front panel to select the option that best describes your system. Select S-W SP ON if a subwoofer is connected to your system. Select S-W SP OFF if a subwoofer is NOT connected to your system. Note that when no subwoofer is selected, low-frequency sounds below 100Hz will be sent to the front left/right speakers, provided that the selection in step 4, above, has been set to LARGE. Otherwise, no low-frequency sounds will be heard. This option is not available when the front, center or surround speakers are set to SMALL.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
System Configuration
18
When
LARGE
is selected, a full-
range output will be sent to the
front left and right outputs, and
NO low-frequency signals will be
sent to the subwoofer output.
5. When you have completed your
selection for the front channel, press
the
Set
button
i˜
, and then
press the
∕
/
¤
buttons
g
on the
remote or the
Selector
buttons
¸
on the front panel to change the dis-
play to
CEN SPEAKER
.
6. Press the
Set
button
i˜
again,
and use the
∕
/
¤
buttons
g
on
the remote, or the
Selector
buttons
¸
on the front panel, to select the
option that best describes your system
based on the speaker definitions
shown above.
When
CEN SP SMALL
is
selected, low-frequency center
channel sounds will be sent to the
subwoofer output only. Note that if
you choose this option and there is
no subwoofer connected, you will
not hear any low-frequency sounds
from the center channel speaker.
When
CEN SP LARGE
is
selected, a full-range output will be
sent to the center speaker output,
and NO center channel signal will
be sent to the subwoofer output.
When
CEN SP NONE
is selected,
no signals will be sent to the center
channel output. The receiver will
operate in a “phantom” center
channel mode and center channel
information will be sent to the left
and right front channel outputs.
7. When you have completed your
selection for the center channel, press
the
Set
button
i˜
, and then
press the
∕
/
¤
buttons
g
on the
remote or the
Selector
buttons
¸
on the front panel to change the
display to
SUR SPEAKER
.
8. Press the
Set
button
i˜
again,
and then use the
∕
/
¤
buttons
g
on the remote or the
Selector
buttons
¸
on the front panel to
select the option that best describes
your system based on the speaker
definitions shown above.
When
SUR SP SMALL
is
selected, low-frequency surround
channel sounds will be sent to the
subwoofer output only. Note that if
you choose this option and there is
no subwoofer connected, you will
not hear any low-frequency sounds
from the surround speaker.
When
SUR SP LARGE
is selected,
a full-range output will be sent to the
surround channel outputs, and NO
surround channel signals will be sent
to the subwoofer output.
When
SUR SP NONE
is selected,
surround sound information will be
split between the front left and front
right outputs. Note that for optimal
performance when no surround
speakers are in use, the Dolby 3
Stereo mode should be used instead
of Dolby Pro Logic.
9. When you have completed your
selection for the surround channel,
press the
Set
button
i˜
, and
then press the
∕
/
¤
buttons
g
on
the remote or the
Selector
buttons
¸
on the front panel to change the display
to
S—W SPEAKER
.
10. Press the
Set
button
i˜
, and
then press the
∕
/
¤
buttons
g
on
the remote or the
Selector
buttons
¸
on the front panel to select the option
that best describes your system.
Select
S-W SP ON
if a subwoofer
is connected to your system.
Select
S-W SP OFF
if a subwoofer is
NOT connected to your system. Note
that when no subwoofer is selected,
low-frequency sounds below 100Hz
will be sent to the front left/right
speakers, provided that the selection
in step 4, above, has been set to
LARGE
. Otherwise, no low-frequency
sounds will be heard. This option is
not available when the front, center or
surround speakers are set to
SMALL
.