Harman Kardon AVR45 Owners Manual - Page 34

Programming the Remote

After following these steps, each time

you press the

Power

button

c

, the

remote will send the Power On/Off

command each time the Power

button is pressed.

To remove a macro program, follow steps

1, 2 and 4 above, but do not follow step

three. For example, to erase the macro

just entered, press the

Device Control

Selector

b

and the

Mute

button

d

at the same time until the red light

under the Device Control Selector turns

on. Press the

Power

button

c

, and

then press the

Sleep

button

`

. The

red light under the

Device Control

Selector

will blink twice to confirm the

data entry and then turn off.

Volume Punch-Through

The AVR45’s remote may be programmed

to operate the

Volume Control

z

from either the TV or the AVR to operate in

conjunction with any of the eight devices

controlled by the remote. For example,

since the AVR45 will likely be used as the

sound system for TV viewing, you may

wish to have the AVR’s volume activated

although the remote is set to run the TV.

Either the AVR or TV volume control may

be associated with any of the remote’s

devices. To program the remote for Volume

Punch-Through, follow these steps:

1. Press the

Device Control Selector

b

for the unit you wish to have asso-

ciated with the volume control and the

Mute

button

d

at the same time

until the red light illuminates under

the


.

2. Press the

Volume Up

button

z

.

3. Press either the

AVR

a

or the

TV Device Control Selector

b

, depending on which system’s

volume control you wish to have

attached for the punch-through mode.

Note that the red light under the


will blink

twice and then go out to confirm the

data entry.

Example:

To have the AVR’s vol-

ume control be activated even

though the remote is set to control

the TV, first press the

TV Device

Control Selector

b

, and the

Mute

button

d

at the same time.

Next, press the

Volume Up

button

z

, followed by the

AVR Device

Control Selector

a

.

NOTE:

Should you wish to return the

remote to the original configuration after

entering a Volume Punch-Through, you

will need to repeat the steps shown above.

However, press the

same

Device Control

Selector in steps one and three.

Re-Assigning Device Control

Selectors

Although each of the seven

Device

Control Selectors

b

is normally

assigned to the category of product shown

on the remote, it is possible to re-assign

one of these buttons to operate a second

device of another type. For example, if you

have two VCRs, but no satellite receiver,

you may program the “SAT” button to

operate a second VCR. Before following

the normal programming steps for either

Three-Digit entry or Auto Search code

entry, you must first re-assign the button

with the following steps:

1. Press the


b

you wish to re-assign and the

Mute

button

d

at the same time

until the red light illuminates under

the


.

2. Press the


b

for the function you wish to

program into the re-assigned button.

3. Enter the three-digit code for the spe-

cific model you wish the re-assigned

button to operate.

4. Press the same

Device Control

Selector

pressed in Step 1 again to

store the selection.

Example:

To use the SAT button to

operate a second VCR, first press the

SAT Device Control Selector

b

, and the

Mute

button

d

at

the same time until the red light

glows under the SAT button. Press

the VCR button, followed by the

three-digit code for the specific

model you wish to control. Finally,

press the SAT button again.

31

Harman Kardon AVR45 Owners Manual - Page 34

Volume Punch-Through, Re-Assigning Device Control, Selectors

Page 34 highlights