Harman Kardon AVR75 Owners Manual - Page 16

System and Power Connections, External Audio Power, Amplifier Connections

Page 16 highlights

Installation and Setup 14 When connecting wires to the speakers, be certain to observe proper polarity. Remember to connect the "negative" or "black" wire to the same terminal on the receiver and the speaker. Similarly, the "positive" or "red" wire should be connected to the like terminal on the AVR75 and speaker. Note: While most speaker manufacturers adhere to an industry convention of using black terminals for negative and red ones for positive, some manufacturers may vary from this configuration. To assure proper phase, and optimal performance, consult the identification plate on your speaker, or the speaker's manual to verify polarity. If you do not know the polarity of your speaker, ask your dealer for advice before proceeding, or consult the speaker's manufacturer. 7. Connections to a subwoofer are made via a line level audio connection from the Subwoofer Output ⁄ to the line level input of a subwoofer with a built-in amplifier. If a passive subwoofer is used, the connection first goes to a power amplifier, which will be connected to one or more subwoofer speakers. Video Input and Output Connections Video connections are made in a similar fashion to those for audio components. Again, the use of high-quality interconnect cables is recommended to preserve signal quality. 1. Connect the VCR's audio, video and S-Video OUT jacks to the Video In jacks d i on the rear panel. The audio, video and S-Video IN jacks on the VCR should be connected to the Video Out jacks e h on the AVR75. 2. Connect the audio and video outputs of a satellite receiver, cable TV converter or television set or any other video source to the TV jacks ª. 3. Connect the audio, video and S-Video outputs of a DVD or laser disc player to the DVD jacks •. 4. Connect the TV Mon f g jacks on the receiver to the video, or S-Video inputs, of your television monitor or video projector. 5. As the AVR75 does not mix or change between standard composite video and S-Video signals, both monitor connections must be made if you use both signal systems. Note: The on-screen menus are visible on the composite video output only. System and Power Connections The AVR75 is designed for flexible use with external control components and power amplifiers. These connections are easy to make during an initial installation, or at a later date should you choose to upgrade your system. Remote Control Extension If the receiver is placed behind a solid or smoked glass cabinet door, the obstruction may prevent the remote sensor from receiving commands. In this event, an optional remote sensor may be used. Connect the output of the remote sensor to the Remote Cont. In jack b. If other components are also prevented from receiving remote commands, only one sensor is needed. They may use this unit's sensor or a remote eye by running a connection from the Remote Cont. Out jack c to the Remote In jack on Harman Kardon or other compatible equipment. External Audio Power Amplifier Connections If desired, optional external power audio power amplifiers may be used with the AVR75. Connections to these amplifiers are made by using audio interconnect cables connected to both the Preamp Outputs , on the rear panel and the audio input jacks of the external amplifiers. AC Power Connections This unit is equipped with two accessory AC outlets. They may be used to power accessory devices, but they should not be used with high-current draw equipment such as power amplifiers. The total power draw may not exceed 50w to each outlet. The Switched fi outlet will receive power only when the unit is on. This is recommended for devices that have no power switch, or a mechanical power switch that may be left in the "ON" position. Note: Devices with electronic power switches may only go into a Standby mode when plugged in here. The Unswitched fl outlet will receive power as long as the unit is plugged into a powered AC outlet. Finally, when all connections are complete, plug the power cord into a nonswitched 120-volt AC wall outlet. You're almost ready to enjoy the AVR75!

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36

Installation and Setup
When connecting wires to the speakers,
be certain to observe proper polarity.
Remember to connect the “negative” or
“black” wire to the same terminal on the
receiver and the speaker. Similarly, the
“positive” or “red” wire should be con-
nected to the like terminal on the AVR75
and speaker.
Note:
While most speaker manufacturers
adhere to an industry convention of using
black terminals for negative and red ones
for positive, some manufacturers may
vary from this configuration. To assure
proper phase, and optimal performance,
consult the identification plate on your
speaker, or the speaker’s manual to verify
polarity. If you do not know the polarity
of your speaker, ask your dealer for advice
before proceeding, or consult the
speaker’s manufacturer.
7. Connections to a subwoofer are made
via a line level audio connection from
the
Subwoofer Output
to the line
level input of a subwoofer with a built-in
amplifier. If a passive subwoofer is used,
the connection first goes to a power
amplifier, which will be connected to one
or more subwoofer speakers.
Video Input and Output Connections
Video connections are made in a similar
fashion to those for audio components.
Again, the use of high-quality intercon-
nect cables is recommended to preserve
signal quality.
1. Connect the VCR’s audio, video and
S-Video OUT jacks to the
Video In
jacks
di
on the rear panel. The audio, video
and S-Video IN jacks on the VCR should
be connected to the
Video Out
jacks
eh
on the AVR75.
2. Connect the audio and video outputs
of a satellite receiver, cable TV converter
or television set or any other video source
to the
TV
jacks
ª
.
3. Connect the audio, video and S-Video
outputs of a DVD or laser disc player to
the
DVD
jacks
.
4. Connect the
TV Mon
fg
jacks on
the receiver to the video, or S-Video
inputs, of your television monitor or
video projector.
5. As the AVR75 does not mix or change
between standard composite video and
S-Video signals, both monitor connec-
tions must be made if you use both
signal systems.
Note:
The on-screen menus are visible
on the composite video output only.
System and Power Connections
The AVR75 is designed for flexible use
with external control components and
power amplifiers. These connections are
easy to make during an initial installa-
tion, or at a later date should you choose
to upgrade your system.
Remote Control Extension
If the receiver is placed behind a solid or
smoked glass cabinet door, the obstruc-
tion may prevent the remote sensor from
receiving commands. In this event, an
optional remote sensor may be used.
Connect the output of the remote sensor
to the
Remote Cont. In
jack
b
.
If other components are also prevented
from receiving remote commands, only
one sensor is needed. They may use this
unit’s sensor or a remote eye by running
a connection from the
Remote Cont.
Out
jack
c
to the Remote In jack on
Harman Kardon or other compatible
equipment.
External Audio Power
Amplifier Connections
If desired, optional external power audio
power amplifiers may be used with the
AVR75. Connections to these amplifiers
are made by using audio interconnect
cables connected to both the
Preamp
Outputs
on the rear panel and
the audio input jacks of the external
amplifiers.
AC Power Connections
This unit is equipped with two accessory
AC outlets. They may be used to power
accessory devices, but they should not be
used with high-current draw equipment
such as power amplifiers. The total power
draw may not exceed 50w to each outlet.
The
Switched
outlet will receive
power only when the unit is on. This is
recommended for devices that have no
power switch, or a mechanical power
switch that may be left in the “ON”
position.
Note:
Devices with electronic power
switches may only go into a Standby
mode when plugged in here.
The
Unswitched
outlet will receive
power as long as the unit is plugged into
a powered AC outlet.
Finally, when all connections are com-
plete, plug the power cord into a non-
switched 120-volt AC wall outlet. You’re
almost ready to enjoy the AVR75!
14