HP 4400 HP StorageWorks Fabric OS 6.2.2e Release Notes (5697-0809, February 20 - Page 28

Web Tools functionality moved to DCFM, Table 7 Web Tools functionality in DCFM

Get HP 4400 PDF manuals and user guides View all HP 4400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Fabric OS version All 8-Gb switches except 8-Gb SAN Switch for HP BladeSystem c-Class 8-Gb SAN Switch for HP BladeSystem c-Class Fabric OS 6.1.2x and Regardless of the Fabric OS version that - If Fabric OS 6.2.0d was 6.2.0d through 6.2.x was previously installed, all ports default factory-installed, all internal ports to IDLE [mode 0]. However if they were remain at ARB(FF) [mode 1], and changed to ARB(FF) [mode 1] manually, external ports remain in IDLE [mode they remain in ARB(FF) mode. 0]. Can be changed by the user. - If Fabric OS earlier than 6.2.0d was factory-installed, all internal and external ports remain at IDLE [mode 0]. However, if they were changed to ARB(FF) [mode 1] manually, then they remain in ARB(FF) mode. Can be changed by the user. Mode: 0 - IDLE for Link Init, IDLE for fill word 1 - ARB(FF) for Link Init, ARB(FF) for fill word (NOTE: not supported with XP storage arrays) • Updated command message: When executing the lscfg --create command with the following syntax: switch_128:FID128:admin> lscfg --create 1 About to create switch with fid=1. Please wait... Logical Switch with FID (1) has been successfully created. You should expect to see the following revised message: Logical Switch has been created with default configurations. Please configure the Logical Switch with appropriate switch and protocol settings before activating the Logical Switch. Web Tools functionality moved to DCFM The functionality that was moved from Web Tools 6.1.1 to DCFM applies to all versions of DCFM and also applies to Fabric OS 6.2.x. Table 7 (page 28) describes these changes. Table 7 Web Tools functionality in DCFM Function Add unzoned devices Web Tools 6.1.0 Zone Admin DCFM Configure > Zoning Reverse Find in the zoning dialog provides the view of the zoned and unzoned devices in the fabric if all zone members are selected for Find. Zone Admin Analyze zone configuration Configure > Zoning Reverse Find in the zoning dialog provides the view of the zoned and unzoned devices in the fabric if all zone members are selected for Find. Device Tree and Topology Connected End Devices Custom display from the top level in the main frame provides the device tree and topology view for all the zoned devices if all zones are selected in the active zone configuration. Define device alias Zone Admin Configure > Zoning 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
8-Gb SAN Switch for HP BladeSystem
c-Class
All 8-Gb switches except 8-Gb SAN
Switch for HP BladeSystem c-Class
Fabric OS version
–
If Fabric OS 6.2.0d was
factory-installed, all internal ports
remain at ARB(FF) [mode 1], and
external ports remain in IDLE [mode
0].
–
If Fabric OS earlier than 6.2.0d was
factory-installed, all internal and
external ports remain at IDLE [mode
0]. However, if they were changed to
ARB(FF) [mode 1] manually, then they
remain in ARB(FF) mode.
Can be changed by the user.
Regardless of the Fabric OS version that
was previously installed, all ports default
to IDLE [mode 0]. However if they were
changed to ARB(FF) [mode 1] manually,
they remain in ARB(FF) mode.
Can be changed by the user.
Fabric OS 6.1.2x and
6.2.0d through 6.2.
x
0 — IDLE for Link Init, IDLE for fill word
1 — ARB(FF) for Link Init, ARB(FF) for fill word (NOTE: not supported with XP storage
arrays)
Mode:
•
Updated command message:
When executing the
lscfg --create
command with the following syntax:
switch_128:FID128:admin> lscfg --create 1 About to create switch
with fid=1. Please wait... Logical Switch with FID (1) has been
successfully created
.
You should expect to see the following revised message:
Logical Switch has been created with default configurations. Please
configure the Logical Switch with appropriate switch and protocol
settings before activating the Logical Switch.
Web Tools functionality moved to DCFM
The functionality that was moved from Web Tools 6.1.1 to DCFM applies to all versions of DCFM
and also applies to Fabric OS 6.2.x.
Table 7 (page 28)
describes these changes.
Table 7 Web Tools functionality in DCFM
DCFM
Web Tools 6.1.0
Function
Configure > Zoning
Reverse Find in the zoning dialog provides the view of
the zoned and unzoned devices in the fabric if all zone
members are selected for Find.
Zone Admin
Add unzoned devices
Configure > Zoning
Reverse Find in the zoning dialog provides the view of
the zoned and unzoned devices in the fabric if all zone
members are selected for Find.
Device Tree and Topology
Connected End Devices
Custom display from the top level in the main frame
provides the device tree and topology view for all the
zoned devices if all zones are selected in the active zone
configuration.
Zone Admin
Analyze zone configuration
Configure > Zoning
Zone Admin
Define device alias
28