HP Designjet L26100 HP Designjet L26500/L26100 Printer Series - Introductory - Page 9

Error code, Recommendation

Get HP Designjet L26100 PDF manuals and user guides View all HP Designjet L26100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Table 1 Numeric error messages (continued) Error code Recommendation 32:01.2 This error occurs when there is a small amount of substrate printed, less than 70 in (178 cm) long. The take-up reel sensor detects that the loop shaper is (incorrectly) at the bottom of its path, even though the spindle motor has been rotating for more than 3 seconds. The most probable cause of this error is that you have forgotten to set the switch direction or tape the substrate to the spindle core, when the substrate reaches the floor and blocks the take-up reel's infrared sensors. Check that there is no obstacle between the take-up reel optical sensors; that the substrate is attached to the take-up reel spindle; and that the take-up reel switch is in the correct position. If necessary, use the take-up reel arrow keys to wind the substrate; then press OK to resume printing. 32:02 This error occurs during printer initialization, to warn you that the take-up reel has been disconnected while the printer was turned off. It also occurs if you try to enable the take-up reel, but it is not connected to the printer. Connect the take-up reel to the printer and press OK to continue. 41:03, 42:03 Turn off the printer using the front panel and the power switch at the rear. Disconnect the power cords. Open the window and check for any visible obstacles restricting the movement of the drive roller. If there is a wrinkled mass of substrate in the substrate path, lift the substrate adjustment lever and clear the obstruction. Reconnect the power cords and turn the printer on again. 44.n A switch has failed. There is noise in the signal of the waste management system. Check that the connector is properly connected. 46:03 Turn off the printer using the front panel and the power switch at the rear. Disconnect the power cords. Reconnect the power cords and turn the printer on again. 61:01 The file format is incorrect and the printer cannot process the job. 61:09 The RIP is unable to communicate with the printer. Check that all relevant cables are properly connected, and check whether the RIP has displayed any error message. ENWW Front-panel error messages 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
Table 1
Numeric error messages (continued)
Error code
Recommendation
32:01.2
This error occurs when there is a small amount of substrate printed, less than
70 in (178 cm) long. The take-up reel sensor detects that the loop shaper is
(incorrectly) at the bottom of its path, even though the spindle motor has been
rotating for more than 3 seconds. The most probable cause of this error is
that you have forgotten to set the switch direction or tape the substrate to the
spindle core, when the substrate reaches the floor and blocks the take-up
reel's infrared sensors. Check that there is no obstacle between the take-up
reel optical sensors; that the substrate is attached to the take-up reel spindle;
and that the take-up reel switch is in the correct position. If necessary, use the
take-up reel arrow keys to wind the substrate; then press
OK
to resume
printing.
32:02
This error occurs during printer initialization, to warn you that the take-up reel
has been disconnected while the printer was turned off. It also occurs if you
try to enable the take-up reel, but it is not connected to the printer. Connect
the take-up reel to the printer and press
OK
to continue.
41:03, 42:03
Turn off the printer using the front panel and the power switch at the rear.
Disconnect the power cords. Open the window and check for any visible
obstacles restricting the movement of the drive roller. If there is a wrinkled
mass of substrate in the substrate path, lift the substrate adjustment lever and
clear the obstruction. Reconnect the power cords and turn the printer on
again.
44.n
A switch has failed. There is noise in the signal of the waste management
system. Check that the connector is properly connected.
46:03
Turn off the printer using the front panel and the power switch at the rear.
Disconnect the power cords. Reconnect the power cords and turn the printer
on again.
61:01
The file format is incorrect and the printer cannot process the job.
61:09
The RIP is unable to communicate with the printer. Check that all relevant
cables are properly connected, and check whether the RIP has displayed any
error message.
ENWW
Front-panel error messages
7