HP Designjet L28500 HP Designjet L28500 Printer Series - Site preparation guid
HP Designjet L28500 Manual
View all HP Designjet L28500 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Designjet L28500 manual content summary:
- HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 1
DESIGNJET L28500 printer series Site preparation guide - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 2
© 2011 Hewlett-Packard Development Company, L.P. 1st edition Legal notices The information contained herein is subject to change without notice. The only warranties for HP Products and services are set forth in the express warranty statement accompanying such products and services. Nothing herein - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 3
Table of contents 1 Overview ...1 Introduction ...1 Customer responsibilities ...1 Installation time schedule ...1 2 Site preparation requirements 2 Physical space requirements ...2 Unloading route ...2 Assembly area ...2 Environmental specifications 3 Ventilation and air conditioning 3 RIP - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 4
iv ENWW - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 5
1 Overview Introduction Your printer is supplied ready to use after a few simple installation procedures described in detail in the Assembly instructions. It is important to read the information provided in this guide thoroughly and to ensure complete compliance with all installation and operation - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 6
) required. Assembly area The space required for assembly is illustrated below: 1 m (39 in) on all sides of the box, except on the side where the printer will be wheeled out, where a space of 6 m (20 ft) is required. Most of the installation process can be done by one person, but two people - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 7
printer. Failure to do so may cause print-quality problems or damage sensitive electronic components. Table 2-2 Printer environmental printer parts and cartridges and can result in ink leaks and printer errors. In this case, HP recommends that you wait at least 3 hours before turning on the printer - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 8
following tasks: NOTE: In order to perform remote support, the printer must have access to the Internet using the LAN connection. ● Have a Gigabit Ethernet should be purchased in addition to the printer and should be available on the day of installation: ● Six HP 792 ink cartridges, one for each - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 9
range. The printer requires three-phase power. Three-phase power provides a more efficient means of supplying large electrical loads than single-phase power, which is common in offices and homes. If only single-phase power is supplied to your facility, contact your HP support representative. ENWW - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 10
printer and should be in accordance with the Electrical Code requirements of the local jurisdiction of the country where the equipment is installed. The printer an isolating transformer) is used to supply power to the printer. An IT power distribution system should not be used. WARNING! Ensure that - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 11
Table 2-5 Cable specifications (continued) Input voltage (line to line) 380-415 V~ (-10%+6%) External diameter range 14-25 mm 200-240 V~ (±10%) 14-25 mm The L1, L2, L3 (& N if any) wires must end with Ferrule terminals. The PE wire must end with a ring terminal (M6). Jumper configuration, 380- - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 12
be kept separate from the power source used for your printer. Grounding The printer must be connected to a good-quality ground line in order to avoid electrical risk. Please note your obligation to comply with the Electrical Code - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 13
Is the electrician aware of all requirements and specifications highlighted in this guide? (Required) Is the three-phase line voltage within the specified for each wall receptacle (wall socket)? (Required) Would the printer's built-in Residual Current Circuit Breaker (also known as Ground - HP Designjet L28500 | HP Designjet L28500 Printer Series - Site preparation guid - Page 14
you arranged for supplies such as substrate and ink cartridges to be available on the day of installation? Is there sufficient space for printer unloading and assembly? Have you met the requirements specified in this guide? Yes No (Required) Comments 10 Chapter 3 Site preparation checklist ENWW
DESIGNJET L28500 printer series
Site preparation guide