HP Model 735 hp 4x speed CD-ROM disk drive user's guide (a1658-90688) - Page 46

Check the Hardware Installation

Get HP Model 735 - Workstation PDF manuals and user guides View all HP Model 735 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Check the Hardware Installation Perform the following steps to check the hardware installation: CAUTION: The CD-ROM drive is susceptible to mechanical and electrostatic shock. When handling the drive, always wear the static strap that came in the CD-ROM drive kit. Always handle the drive carefully. 1. Check that the SCSI-2 terminator is connected to the single-ended SCSI-2 port on the rear I/O panel of the system unit (if there are no external SCSI-2 devices), or that the last external single-ended SCSI-2 device is terminated. 2. Attach the static-grounding wrist strap by following the instructions on the package that contains the strap. 3. Shut down HP-UX. NOTICE: If you are already at the boot administration level, you do not need to shut down; skip this step and go on to Step 4. If you are running HP-UX under HP VUE, shut down your system by performing the shutdown procedure described in the System Owner's Guide which came with your workstation. If you are running HP-UX without HP VUE, shut down your system by typing the following command: # /etc/shutdown -h RETURN You must have superuser privileges to use the /etc/shutdown command. If you do not have superuser privileges, contact your system administrator. If your workstation is part of a cluster, refer to the manual, Managing Clusters of HP 9000 Computers for instructions on shutting down. 4. Power off the workstation, using the power switch on the front of the workstation. 3-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
3–6
Check the Hardware Installation
Perform the following steps to check the hardware installation:
CAUTION:
The CD-ROM drive is susceptible to mechanical and electrostatic
shock. When handling the drive, always wear the static strap that came
in the CD-ROM drive kit. Always handle the drive carefully.
1.
Check that the SCSI-2 terminator is connected to the single-ended SCSI-2 port on the
rear I/O panel of the system unit (if there are no external SCSI-2 devices), or that the
last external single-ended SCSI-2 device is terminated.
2.
Attach the static-grounding wrist strap by following the instructions on the package that
contains the strap.
3.
Shut down HP-UX.
NOTICE:
If you are already at the boot administration level, you do not need to
shut down; skip this step and go on to Step 4.
If you are running HP-UX under HP VUE, shut down your system by performing the
shutdown procedure described in the System Owner’s Guide which came with your
workstation.
If you are running HP-UX without HP VUE, shut down your system by typing the fol-
lowing command:
#
/etc/shutdown –h
RETURN
You must have superuser privileges to use the
/etc/shutdown
command. If you do not
have superuser privileges, contact your system administrator.
If your workstation is part of a cluster, refer to the manual,
Managing Clusters of HP
9000 Computers
for instructions on shutting down.
4.
Power off the workstation, using the power switch on the front of the workstation.