HP Officejet v40 HP Officejet V Series - (English) User Guide - Page 11

Make sure it is free of rips, dust, wrinkles, and curled or bent edges. - director

Get HP Officejet v40 - All-in-One Printer PDF manuals and user guides View all HP Officejet v40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

4 /RDG SDSHU RU WUDQVSDUHQ.\ ILOP RU ORDG RULJLQDOV Your unit is designed to print and copy onto a variety of transparency films and paper types, weights, and sizes. It is important, however, that you choose the right paper and make sure that it is not damaged. For comprehensive information, see the fully searchable Onscreen Guide. To access the guide, go to the Director, click Help, and choose Onscreen Guide. /RDG WKH LQSXW WUD\ ZLWK OHWWHU OHJDO RU $VL]H SDSHU For best results, adjust the paper settings each time you change paper types or paper sizes. For more information, see "Set the paper type." 1 Pull out the bottom (input) tray, and slide the paper-width and -length adjusters to their outermost positions. 2 Tap the stack on a flat surface to even the edges of the paper, and then check the paper for the following: • Make sure it is free of rips, dust, wrinkles, and curled or bent edges. • Make sure all the paper in the stack is the same size and type, unless you are working with photo paper. 3 Insert paper into the input tray, print-side down and letterhead or top of page first, until it stops. Do not overfill the input tray as this may cause paper jams. Chapter 4-Load paper or transparency film, or load originals 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Chapter 4—Load paper or transparency film, or load originals
7
4
/RDG²SDSHU²RU²WUDQVSDUHQ±\²ILOPº²RU²ORDG²RULJLQDOV
Your unit is designed to print and copy onto a variety of transparency films and paper
types, weights, and sizes. It is important, however, that you choose the right paper and
make sure that it is not damaged.
For comprehensive information, see the fully searchable Onscreen Guide. To access the
guide, go to the Director, click Help, and choose Onscreen Guide.
/RDG²WKH²LQSXW²WUD\²ZLWK²OHWWHUÀº²OHJDOÀº²RU²$¹ÀVL]H²SDSHU
For best results, adjust the paper settings each time you change paper types or paper
sizes. For more information, see “Set the paper type.”
1
Pull out the bottom (input) tray, and slide the paper-width and -length adjusters to
their outermost positions.
2
Tap the stack on a flat surface to even the edges of the paper, and then check the
paper for the following:
•
Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
•
Make sure all the paper in the stack is the same size and type, unless you are
working with photo paper.
3
Insert paper into the input tray, print-side down and letterhead or top of page first,
until it stops. Do not overfill the input tray as this may cause paper jams.