HP Scitex LX850 HP Scitex LX850 & LX820 Printers: Site Preparation Guide -
HP Scitex LX850 Manual
View all HP Scitex LX850 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Scitex LX850 manual content summary:
- HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 1
SCITEX LX850 & LX820 Printers Site preparation guide - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 2
The only warranties for HP Products and services are set forth in the express warranty statement accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 3
Introduction ...1 System configuration ...1 Documentation ...1 Site preparation overview ...1 Customer responsibility ...2 2 Site preparation ...5 Planning for printer installation 5 Installation time schedule ...5 System operation requirements 6 Air supply requirements (pneumatic spindle 10 Room - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 4
iv ENWW - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 5
The following manuals are provided with your printer, and can also be downloaded from http://www.hp.com/go/LX820/manuals/ or http://www.hp.com/go/LX850/manuals/. ● Site preparation guide ● Site preparation checklist ● User's guide ● Maintenance and troubleshooting guide ● Legal information - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 6
equipment to handle the printer, as well as a specialist mover who is familiar with your site and the information provided in this guide. See Moving installations on page 13. RIP installation If you have bought HP RIP software for your printer: ● You must ensure that a computer is available on - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 7
no cartridges are supplied with the printer) NOTE: In addition, you are recommended to have a second set of six ink cartridges, three printheads and one maintenance kit, in case any replacements are needed. ● Compressed air supply for the pneumatic spindle. See Air pressure supply on page 10. ● Some - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 8
further information, please refer to the MSDS document about your printer's ink, available from http://www.hp.com/hpinfo/community/ environment/productinfo/psis_inkjet.htm. Within some countries covered by the 'HP Planet Partners Returns', HP is offering a recycling program. For full details of this - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 9
of the RIP. The following aspects of RIP usage will be covered: HP Scitex Onyx RIP ● Queue manager ● Configure Printer (Quickset, Device Output, Media, Page size, Properties) ● Main items of the Preflight (Printer and Media Selection, Preview and Size, Tiling Setup, Color Correction, Print) ENWW - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 10
including three-phase branch circuit breaker 5. HP Internal Print Server computer NOTE: Remember that you are required to follow the local laws, regulations, and standards that pertain to the electrical installation of your printer. NOTE: The LX820 or LX850 are not supplied with a three-phase cable - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 11
Site preparation Power distribution unit (PDU) NOTE: The PDU must be rated to meet the power requirements of the printer, and should be in accordance with the Electrical Code requirements of the local jurisdiction of the country where the equipment is installed. The drying and curing components are - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 12
HP highly recommends that you use a UPS. Circuit breakers (required) NOTE: The circuit breakers must meet the requirements of the printer and should be in accordance with the Electrical Code 3 poles, 63 A Table 2-5 LX820 & LX850 single-phase circuit breaker specifications High-voltage systems - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 13
5% voltage sag. If the maximum variation is not within this range, print quality and printer operation may be affected. Contact your electricity supplier to remedy any voltage unbalance or sag. To avoid certain specific system errors in some cases, such as 15.8:10 or 16.8:10, you are recommended to - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 14
wire from the main building service panel. These should run in HP recommends that you use an air compressor with a pressure gauge that measures in bars. Table 2-7 Air supply specifications Specification Air pressure ) Regulator with pressure gauge Pneumatic connector The printer comes with an - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 15
image quality problems or damage sensitive electronic components. Table 2-8 Printer environmental specifications °C/h (50°F/h) or less Not operating (in transport or 5 to 55°C (41 to 131°F) storage), ink in tubes 90% Relative Humidity at 55°C (131°F) 10°C/h (50°F/h) or less Not operating (in - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 16
vapors may be produced when printing with water-based HP Latex inks, especially when printing on porous substrates. In high- LX850 1100 kg (2425 lb) 367 kg (809 lb) Your printer has four wheels used to move the printer and three feet that must be lowered to touch the ground and support the printer - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 17
Site preparation LX820 & LX850 A 5.718 m (225.11 in) B 3.650 m (143.69 in) C 1.485 m (58.46 in) (no carpet) ● Easy to clean ● Durable ● Free from strong vibrations Lighting Whenever your printer is in operation, the print production area should be well lit to provide the operator with - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 18
following tasks: ● Print ● Use the HP Internal Print Server ● Replace a substrate roll ● Service the printer or replace printer components ● Ensure the printer is well ventilated Your printer has the following dimensions: Table 2-9 LX820 & LX850 physical specifications Doors closed1 Doors open2 - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 19
materials used with the printer, thought should not only be given to safety and convenience, but also to the fact that if inks and substrates are not Computer and networking requirements LAN and switch requirements To use CallMe@HP for remote support, you need one of the following: ● A direct, open - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 20
duplex), there will be no communication. RIP requirements There are two RIPs offered by HP that may be used with the printer: ● HP Scitex Onyx RIP (Production House): product number CQ756A ● HP Scitex Caldera RIP (GrandRIP+): product number CQ755A The software and hardware requirements of these RIPs - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 21
with the latest service pack ◦ Windows 7 Business or Enterprise 32-bit and 64-bit with the latest service pack HP Scitex Onyx X10 RIP support.php?page=operating_system ● http://www.caldera.eu/docs/Datasheet_GrandRIP+_UK.pdf External color profiling In order to build color profiles for your printer - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 22
During the installation training, it is the customer's responsibility to have a RIP specialist available to create color profiles. Site preparation 18 Chapter 2 Site preparation ENWW - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 23
corridor width Minimum corridor width for a 90° turn 1.85 m (72.9 in) 2 m (78.8 in) 1.85 m (72.9 in) 3.2 m (126 in) 2 m (78.8 in) 2.5 m (98.5 in) 2 m (78.8 in) 3.65 m (144 in) WARNING! After being removed from the crate, the printer cannot be moved up or down a ramp. If you need to move the - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 24
crate and printer are as follows: Table 3-2 LX850/LX820 printer and crate physical specifications Length Width Height Weight Crate Printer 5.86 m printer and all system components is the customer's responsibility and not HP of your printer. Advanced booking for the services of a machinery - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 25
Arrival preparation ● Two skates to move the crate (optional) ● Electric pallet jack (optional) ENWW Moving equipment 21 - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 26
bars are inserted into the forklift guides and connected with lifting cables to the crane. CAUTION: When lifting the printer with a crane, extra caution should be taken to ensure that the cables do not apply pressure to the scan beam or any other printer component. CAUTION: This attachment is used - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 27
be long enough so that the lift cables do not touch the printer. The following graphic illustrates how to lift the printer with a spreader beam. CAUTION: When lifting the printer with a crane, extra caution should be taken to ensure that the cables do not apply pressure to the scan beam or any other - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 28
Arrival preparation Waste disposal You must dispose of the crate and packaging material that comes with the printer. Most of the waste will be wood materials. 24 Chapter 3 Shipment arrival preparation ENWW
SCITEX LX850 & LX820 Printers
Site preparation guide