HP Scitex LX850 HP Scitex LX850 & LX820 Printers: Site Preparation Guide - - Page 7

Networking, Printing supplies for testing and training, Return the site preparation checklist

Get HP Scitex LX850 PDF manuals and user guides View all HP Scitex LX850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Introduction NOTE: This guide does not provide information about your RIP solution. ● You must install the RIP on a suitable computer and ensure that it is fully functional by the agreed date of printer installation. ● For full functionality, you are recommended to ensure that the computer is connected to the Internet. ● You must ensure that a RIP specialist and a network specialist are present on the agreed date of printer installation. Networking You are responsible for all networking requirements, and you must complete the following tasks: NOTE: In order to perform remote support, the printer must have access to the internet using the LAN connection. ● Have an adequate network ready for the day of installation. See Computer and networking requirements on page 15. ● Provide a CAT-6 LAN cable to connect the printer to your LAN on the day of installation. Printing supplies for testing and training You are responsible for providing the following printing supplies: ● Six ink cartridges, one for each color (no cartridges are supplied with the printer) NOTE: In addition, you are recommended to have a second set of six ink cartridges, three printheads and one maintenance kit, in case any replacements are needed. ● Compressed air supply for the pneumatic spindle. See Air pressure supply on page 10. ● Some rolls of substrate for printing; preferably the substrate type that you plan to use most in future ● To test the ink collector kit (LX850 only), a roll of flexible substrate (mesh or thin textile, without liner) ● To test dual-roll printing (LX850, or LX820 with Dual Roll Kit), two rolls of 1524 mm ( (60 in)). Return the site preparation checklist The checklist must be completed and returned to your reseller or service representative a minimum of two weeks before the day of installation. NOTE: Any delays during installation that are caused by an unprepared site will be charged to the customer. Take care that your site is properly prepared to ensure a smooth and easy installation. Recycle the disposable ink bag and maintenance kit (printhead cleaning roller and aerosol filters) These items require disposal according to local regulations. For further information, please refer to the MSDS document about your printer's ink, available from http://www.hp.com/hpinfo/community/ environment/productinfo/psis_inkjet.htm. ENWW Customer responsibility 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
NOTE:
This guide does not provide information about your RIP solution.
●
You must install the RIP on a suitable computer and ensure that it is fully functional by the agreed
date of printer installation.
●
For full functionality, you are recommended to ensure that the computer is connected to the
Internet.
●
You must ensure that a RIP specialist and a network specialist are present on the agreed date of
printer installation.
Networking
You are responsible for all networking requirements, and you must complete the following tasks:
NOTE:
In order to perform remote support, the printer must have access to the internet using the LAN
connection.
●
Have an adequate network ready for the day of installation. See
Computer and networking
requirements
on page
15
.
●
Provide a CAT-6 LAN cable to connect the printer to your LAN on the day of installation.
Printing supplies for testing and training
You are responsible for providing the following printing supplies:
●
Six ink cartridges, one for each color (no cartridges are supplied with the printer)
NOTE:
In addition, you are recommended to have a second set of six ink cartridges, three
printheads and one maintenance kit, in case any replacements are needed.
●
Compressed air supply for the pneumatic spindle. See
Air pressure supply
on page
10
.
●
Some rolls of substrate for printing; preferably the substrate type that you plan to use most in future
●
To test the ink collector kit (LX850 only), a roll of flexible substrate (mesh or thin textile, without
liner)
●
To test dual-roll printing (LX850, or LX820 with Dual Roll Kit), two rolls of 1524 mm ( (60 in)).
Return the site preparation checklist
The checklist must be completed and returned to your reseller or service representative a minimum of
two weeks before the day of installation.
NOTE:
Any delays during installation that are caused by an unprepared site will be charged to the
customer. Take care that your site is properly prepared to ensure a smooth and easy installation.
Recycle the disposable ink bag and maintenance kit (printhead
cleaning roller and aerosol filters)
These items require disposal according to local regulations. For further information, please refer to the
MSDS document about your printer's ink, available from
hpinfo/community/
environment/productinfo/psis_inkjet.htm
.
ENWW
Customer responsibility
3
Introduction