HP Surestore E Disk Array XP256 HP XP P9000 External Storage Access Manager Us - Page 74

The following table lists the codes for the errors that can occur when using RAID Manager and

Get HP Surestore E Disk Array XP256 PDF manuals and user guides View all HP Surestore E Disk Array XP256 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

The following table lists the codes for the errors that can occur when using RAID Manager and the steps involved in troubleshooting the errors. Error code (SSB1) 2E31 B90A B90A B90A Error code (SSB2) 9100 B901 B902 B904 B90A B90A B90A B90A B912 D004 B980 B981 B982 B983 B902 CBEF Description You cannot run the command because the user was not authenticated. An ESAM pair cannot be created or resynchronized because ESAM does not support the option, or the command cannot be accepted in the current pair status. An ESAM pair cannot be created or resynchronized because the quorum disk is being blocked. Reservations that are set to the P-VOL by the host have been propagated to the S-VOL by ESAM. The cause is one of the following: • The pair cannot be created because the reservations that were propagated earlier still remain in the volume. Wait then try again. • You cannot run the horctakeover and pairresync - swaps commands because the reservations that were propagated to the S-VOL remain in the volume. Wait then try the command again. If the error occurs again, release the LUN reservation by host, and then try the command again. For more information about how to release the LUN reservation by host, see the HP XP P9000 Provisioning for Open Systems User Guide. An ESAM pair cannot be created because the Continuous Access Synchronous program product is not installed. An ESAM pair cannot be created because the ESAM program product is not installed. An ESAM pair cannot be created or resynchronized because the specified quorum disk ID was not added to the secondary storage system. The specified value of the quorum disk ID is out of range. An ESAM pair cannot be suspended because of one of the following conditions: • ESAM does not support the pairsplit -rw command. • The operation cannot be accepted in the current pair status. One of the following causes apply: • An ESAM pair cannot be created or resynchronized because of one of the following causes: - The specified quorum disk ID is not added to secondary storage system. - The specified quorum disk ID does not match the quorum disk ID that the S-VOL uses. - The same quorum disk ID is assigned to different external volumes separately by the primary and secondary storage systems. - On the paired CU side, the specified quorum disk ID is configured to a different external volume. - The quorum disk is blocked, or the path between secondary storage system and the quorum disk has a failure. • The pair cannot be resynchronized using the Sync copy mode because the S-VOL has the ESAM attribute. 74 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
The following table lists the codes for the errors that can occur when using RAID Manager and the
steps involved in troubleshooting the errors.
Description
Error code
(SSB2)
Error code
(SSB1)
You cannot run the command because the user was not authenticated.
9100
2E31
An ESAM pair cannot be created or resynchronized because ESAM does not support
the option, or the command cannot be accepted in the current pair status.
B901
B90A
An ESAM pair cannot be created or resynchronized because the quorum disk is being
blocked.
B902
B90A
Reservations that are set to the P-VOL by the host have been propagated to the S-VOL
by ESAM. The cause is one of the following:
B904
B90A
•
The pair cannot be created because the reservations that were propagated earlier
still remain in the volume. Wait then try again.
•
You cannot run the
horctakeover
and
pairresync - swaps
commands because
the reservations that were propagated to the S-VOL remain in the volume. Wait then
try the command again.
If the error occurs again, release the LUN reservation by host, and then try the
command again.
For more information about how to release the LUN reservation by host, see the
HP
XP P9000 Provisioning for Open Systems User Guide
.
An ESAM pair cannot be created because the Continuous Access Synchronous program
product is not installed.
B980
B90A
An ESAM pair cannot be created because the ESAM program product is not installed.
B981
B90A
An ESAM pair cannot be created or resynchronized because the specified quorum disk
ID was not added to the secondary storage system.
B982
B90A
The specified value of the quorum disk ID is out of range.
B983
B90A
An ESAM pair cannot be suspended because of one of the following conditions:
B902
B912
•
ESAM does not support the
pairsplit -rw
command.
•
The operation cannot be accepted in the current pair status.
One of the following causes apply:
CBEF
D004
•
An ESAM pair cannot be created or resynchronized because of one of the following
causes:
- The specified quorum disk ID is not added to secondary storage system.
- The specified quorum disk ID does not match the quorum disk ID that the S-VOL uses.
- The same quorum disk ID is assigned to different external volumes separately by the
primary and secondary storage systems.
- On the paired CU side, the specified quorum disk ID is configured to a different
external volume.
- The quorum disk is blocked, or the path between secondary storage system and the
quorum disk has a failure.
•
The pair cannot be resynchronized using the Sync copy mode because the S-VOL has
the ESAM attribute.
74
Troubleshooting