HP T5630w Microsoft Windows Embedded Standard 2009 (WES) v. 5.1.810 and later - Page 45

DOS Command-line Tool Boot Commands, Using Boot Commands

Get HP T5630w - Compaq Thin Client PDF manuals and user guides
UPC - 884962252574
View all HP T5630w manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

DOS Command-line Tool Boot Commands The following table lists the EWF boot commands that are supported. Boot Command Description All Commit Disable Displays information about all protected volumes and performs a command, such as disable, enable, and commit, on each volume if specified. Commits all current level data in the overlay to the protected volume, and resets the current overlay level to 1 upon shutdown. Allows user to write to the image after the next reboot. Enable Prevents the user from writing to the image after the next reboot. Commitanddisable Combination of the Commit and Disable commands. This command will commit data in the overlay upon shutdown. Additionally, EWF will be disabled after the system reboots. NOTE: When using the Commit boot command, all the temporary contents will be permanently written to the flash memory. In addition, all content accessed (and changes made) after running Commit, but before rebooting the system, will be written to the flash memory as well. This includes changes made during any number of login/logout sessions before the next reboot. Using Boot Commands To use the EWF manager boot commands, type the following syntax in a command prompt: EWFMGR -[boot command]. NOTE: Because the EWF manager commands are executed on the next boot, you must reboot the system for the command to take effect. ENWW Write Filters 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
DOS Command-line Tool Boot Commands
The following table lists the EWF boot commands that are supported.
Boot Command
Description
All
Displays information about all protected volumes and performs a command, such as
disable
,
enable
,
and
commit
, on each volume if specified.
Commit
Commits all current level data in the overlay to the protected volume, and resets the current overlay level
to 1 upon shutdown.
Disable
Allows user to write to the image after the next reboot.
Enable
Prevents the user from writing to the image after the next reboot.
Commitanddisable
Combination of the
Commit
and
Disable
commands. This command will commit data in the overlay upon
shutdown. Additionally, EWF will be disabled after the system reboots.
NOTE:
When using the Commit boot command, all the temporary contents will be permanently written
to the flash memory. In addition, all content accessed (and changes made) after running Commit, but
before rebooting the system, will be written to the flash memory as well. This includes changes made
during any number of login/logout sessions before the next reboot.
Using Boot Commands
To use the EWF manager boot commands, type the following syntax in a command prompt:
EWFMGR <drive-letter> —[boot command]
.
NOTE:
Because the EWF manager commands are executed on the next boot, you must reboot the
system for the command to take effect.
ENWW
Write Filters
37