HP Visualize J5000 hp Visualize J5000, J7000 workstations owner's guide (a5991 - Page 153
Changing the Console to External Terminal
 |
View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 153 highlights
The Boot Console Interface Changing the Console to External Terminal Changing the Console to External Terminal In the event that your console stops displaying to your graphics device, use the following procedure to display the console to an external serial terminal so that you can configure the graphics console: 1. Turn the system's power off. 2. Disconnect the USB keyboard connector from the system rear panel. 3. Connect a serial terminal to the serial connector 1 on the system rear panel. The serial parameters are: 9600 baud, 8 data bits, no stop bits. 4. Power on the system. The system will now display the console to the terminal connected to Serial 1 port. Chapter 8 153
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148 -
149 -
150 -
151 -
152 -
153 -
154 -
155 -
156 -
157 -
158 -
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
 |
 |
Chapter 8
153
The Boot Console Interface
Changing the Console to External Terminal
Changing the Console to External Terminal
In the event that your console stops displaying to your graphics device,
use the following procedure to display the console to an external serial
terminal so that you can configure the graphics console:
1.
Turn the system’s power off.
2.
Disconnect the USB keyboard connector from the system rear panel.
3.
Connect a serial terminal to the serial connector 1 on the system rear
panel. The serial parameters are: 9600 baud, 8 data bits, no stop bits.
4.
Power on the system.
The system will now display the console to the terminal connected to
Serial 1 port.