Hitachi 50V500 Owners Guide - Page 37

Using The Remote To Control Vcr Functions - light codes

Get Hitachi 50V500 - UltraVision Digital - 50inch Rear Projection TV PDF manuals and user guides View all Hitachi 50V500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

THE REMOTE CONTROL USING THE REMOTE TO CONTROL VCR FUNCTIONS Operating the precoded function for your VCR. This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR (refer to page 43 for pre-codes). 1. Turn ON your VCR. 2. Aim the remote control at the front of your VCR. 3. Press and release the VCR button to switch to VCR pre-coded mode. 4. Hold down the VCR button on the remote and enter the two digit preset code that matches your VCR, as shown on page 43. The indicator light will flash 3 times if the code was accepted. 5. Aim the remote at the VCR and press the POWER button. The remote will turn off your VCR when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your VCR. If the VCR does not turn off, try a different two digit preset code. 6. The remote will now control your VCR. NOTES: 1. If your VCR cannot be operated after performing the above procedures, your VCR's code has not been precoded into the remote. 2. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide. 3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. 4. The MENU button will act as the VCR MENU button for HITACHI VCRs. 5. The LAST CH button will act as your VCR ENTER button if required. 6. The SLEEP button will act as your VCR '100' button if required. ቢ VCR Button This button allows the remote to control your VCR by setting it to VCR mode. ባ PRECODED VCR Buttons These buttons transmit the chosen precoded VCR codes. For some VCRs, you must press the RECORD button twice to record a program. ቤ EXCLUSIVE TV Buttons These buttons are for operating the TV. ባ ባ ቤ POWER TV DVD VCR CBL SOURCE WIZARD CD PVR STB AMP 1 2 3 ቢ 4 5 6 ባ 7 8 9 SLEEP C.C. ANT 0 INFO A/V NET ASPECT VIDEO ቤ MENU EXIT ቤ VOL SELECT CH ባ MUTE LAST CH VID1 VID2 PIP VID3 SURF VID5 VID4 FREEZE PIP MODE PIP ACCESS SWAP DAY/NIGHT ቤ ቤ ባ REC CLU-5729TSI MY VCR CODE IS: NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
37
USING THE REMOTE TO CONTROL VCR FUNCTIONS
Operating the precoded function for your VCR.
This remote is designed to operate different types of VCRs.
You must first program the remote to match the remote system of your VCR
(refer to page 43 for pre-codes).
1.
Turn ON your VCR.
2.
Aim the remote control at the front of your VCR.
3.
Press and release the VCR button to switch to VCR pre-coded mode.
4.
Hold down the VCR button on the remote and enter the two digit preset code that matches your VCR, as shown on page 43.
The
indicator light will flash 3 times if the code was accepted.
5.
Aim the remote at the VCR and press the POWER button.
The remote will turn off your VCR when the correct two digit preset code
is entered.
When this occurs, the remote control is programmed for your VCR.
If the VCR does not turn off, try a different two digit
preset code.
6.
The remote will now control your VCR.
NOTES:
1.
If your VCR cannot be operated after performing the
above procedures, your VCR’s code has not been
precoded into the remote.
2.
In the unlikely event that your VCR cannot be operated
after performing the above procedures, please consult
your VCR operating guide.
3.
The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control.
After replacing the batteries repeat the
entire programming procedure as stated above.
4.
The MENU button will act as the VCR MENU button for
HITACHI VCRs.
5.
The LAST CH button will act as your VCR ENTER button
if required.
6.
The SLEEP button will act as your VCR ‘100’ button if
required.
³
VCR Button
This button allows the remote to control your VCR by
set-
ting it to VCR mode.
´
PRECODED VCR Buttons
These buttons transmit the chosen precoded VCR codes.
For some VCRs, you must press the RECORD button twice
to record a program.
±
EXCLUSIVE TV Buttons
These buttons are for operating the TV.
±
³
´
±
´
±
´
±
´
´
±
POWER
TV
VCR
CBL
DVD
1
2
4
5
6
3
7
8
9
0
INFO
SLEEP
A/V NET
EXIT
MENU
CH
VOL
MUTE
PIP
SURF
SWAP
FREEZE
PIP MODE
PIP ACCESS
DAY/NIGHT
SOURCE WIZARD
REC
SELECT
C.C.
ASPECT
STB
ANT
LAST CH
VID1
VID2
VID3
VID4
VID5
PVR
CD
AMP
VIDEO
CLU-5729TSI
MY VCR CODE IS:
NOTE:
Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR.
THE REMOTE CONTROL