Hitachi D10VG Instruction Manual - Page 7

Carefully handle power tools.

Get Hitachi D10VG - 3/8 Inch Drill 9.0 Amp PDF manuals and user guides
UPC - 717709006157
View all Hitachi D10VG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

English 13. Blades and accessories must be securely mounted to the tool. Prevent potential injuries to youself or others. Blades, cutting implements and accessories which have been mounted to the tool should be secure and tight. 14. Keep motor air vent clean. The tool's motor air vent must be kept clean so that air can freely flow at all times. Check for dust build-up frequently. 15. Operate power tools at the rated voltage. Operate the power tool at voltages specified on its nameplate. If using the power tool at a higher voltage than the rated voltage, it will result in abnormally fast motor revolution and may damage the unit and the motor may burn out. 16. NEVER use a tool which is defective or operating abnormally. If the tool appears to be operating unusually, making strange noises, or otherwise appears defective, stop using it immediately and arrange for repairs by a Hitachi authorized service center. 17. NEVER leave tool running unattended. Turn power off. Don't leave tool until it comes to a complete stop. 18. Carefully handle power tools. Should a power tool be dropped or struck against hard materials inadvertently, it may be deformed, cracked, or damaged. 19. Do not wipe plastic parts with solvent. Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may damage and crack plastic parts. Do not wipe them with such solvents. Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry thoroughly. 20. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI Standard Z87.1. 21. ALWAYS be careful with buried object such as an underground wiring. Touching these active wiring or electric cable with this tool, you may receive an electric shock. Confirm if there are any buried object such as electric cable within the wall, floor or ceiling where you are going tos operate here after. 22. Definitions for symbols used on this tool V volts Hz .......... hertz A amperes no .......... no load speed W watt Class II Construction ---/min ... revolutions per minute 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
English
7
13.
Blades and accessories must be securely mounted to the tool.
Prevent potential injuries to youself or others. Blades, cutting implements and accessories
which have been mounted to the tool should be secure and tight.
14.
Keep motor air vent clean.
The tool’s motor air vent must be kept clean so that air can freely flow at all times. Check
for dust build-up frequently.
15.
Operate power tools at the rated voltage.
Operate the power tool at voltages specified on its nameplate.
If using the power tool at a higher voltage than the rated voltage, it will result in
abnormally fast motor revolution and may damage the unit and the motor may burn out.
16.
NEVER use a tool which is defective or operating abnormally.
If the tool appears to be operating unusually, making strange noises, or otherwise
appears defective, stop using it immediately and arrange for repairs by a Hitachi
authorized service center.
17.
NEVER leave tool running unattended. Turn power off.
Don’t leave tool until it comes to a complete stop.
18.
Carefully handle power tools.
Should a power tool be dropped or struck against hard materials inadvertently, it may
be deformed, cracked, or damaged.
19.
Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may
damage and crack plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry
thoroughly.
20. ALWAYS
wear eye protection that meets the requirement of the latest revision of ANSI
Standard Z87.1.
21. ALWAYS
be careful with buried object such as an underground wiring.
Touching these active wiring or electric cable with this tool, you may receive an electric
shock.
Confirm if there are any buried object such as electric cable within the wall, floor or
ceiling where you are going tos operate here after.
22.
Definitions for symbols used on this tool
V
............
volts
Hz
..........
hertz
A
............
amperes
n
o
..........
no load speed
W
...........
watt
...........
Class
II
Construction
---/min ... revolutions per minute