Hotpoint RGBS200DMWW Use and Care Manual - Page 19

Oven Door, Oven Light, CARE AND CLEANING

Get Hotpoint RGBS200DMWW PDF manuals and user guides View all Hotpoint RGBS200DMWW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

CARE AND CLEANING: 2YHQ/LJKW2YHQ'RRU Oven Light WARNING SHOCK OR BURN HAZARD: Before replacing oven light bulb, disconnect the electrical power to the range at the main fuse or circuit breaker panel. Failure to do so may result in electric shock or burn. CAUTION BURN HAZARD: The glass cover and bulb should be removed when cool. Touching hot glass with bare hands or a damp cloth can cause burns. CAUTION Before replacing your oven light bulb, disconnect the electrical power to the range at the main fuse or circuit breaker panel. Be sure to let the light cover and bulb cool completely. The oven light bulb is covered with a removable glass cover that is held in place with a bail-shaped wire. Remove the oven door, if desired, to reach the cover easily. See the Lift-Off Oven Door section for detailed oven door removal instructions. Replacing the Light Bulb (glass cover on self clean models only):  'LVFRQQHFWHOHFWULFDOSRZHUWRWKHUDQJH 2. Hold the glass cover stable, so it doesn't fall when released. 3. Slide near the indent of the cover holder until the cover is released. Do not remove any screws to release the glass cover.  3XOOWKHZLUHFRYHUKROGHUQHDUWKHLQGHQWXQWLOWKH indent in the wire cover holder is located in the indent of the glass cover. 7. Connect electrical power to range. *ODVVFRYHU RQVHOI FOHDQPRGHORQO\  5HSODFHEXOEZLWKDZDWWKRXVHKROGDSSOLDQFH bulb. Do not touch hot bulb with hand or wet cloth. Only remove bulb when it is cool. 5. Hold glass cover stable over new bulb. Indent Wire cover holder Oven Door The door is very heavy. Be careful when removing and lifting the door. Do not lift door by the handle. Removing the Door:  )XOO\RSHQWKHRYHQGRRU 2. On each hinge, slide the hinge lock up, making sure it snaps into its fully raised position. 3. Firmly grasp both sides of the door near the handle. 4. Close the door until the top of the door is approximately 3" from the range frame. 5. Lift door up and away from the range until both hinge arms are clear of the slots in the range frame. Replacing the Door:  )LUPO\JUDVSERWKVLGHVRIWKHGRRUQHDUWKHKDQGOH 3XOOKLQJHORFNVXSWRXQORFN Removal position 2. With the door at the same angle as the removal position, rest the notch in the bottom of the left hinge arm on the bottom edge of the left hinge slot. The notch in the hinge arm must be fully seated onto the bottom of the slot. Repeat for the right side. 3. Fully open the door. If the door will not fully open, the hinge arms are not seated correctly. Lift the door off the range and repeat Step 2.  3XVKWKHKLQJHORFNVGRZQWRWKHORFNHGSRVLWLRQ Notch 3XVKKLQJHORFNVGRZQWRORFN 5. Close the oven door. 49-2000315 Rev. 1 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
49-2000315
Rev. 1
Oven Door
The door is very heavy. Be careful when removing and lifting the door. Do not lift door by the handle.
Removing the Door:
2. On each hinge, slide the hinge lock up, making sure it
snaps into its fully raised position.
3. Firmly grasp both sides of the door near the handle.
4. Close the door until the top of the door is
approximately 3” from the range frame.
5. Lift door up and away from the range until both hinge
arms are clear of the slots in the range frame.
Replacing the Door:
2. With the door at the same angle as the removal
position, rest the notch in the bottom of the left hinge
arm on the bottom edge of the left hinge slot. The
notch in the hinge arm must be fully seated onto the
bottom of the slot. Repeat for the right side.
3. Fully open the door. If the door will not fully open, the
hinge arms are not seated correctly. Lift the door off
the range and repeat Step 2.
5. Close the oven door.
Oven Light
CARE AND CLEANING:
Notch
Removal position
WARNING
SHOCK OR BURN HAZARD:
Before replacing oven light bulb, disconnect the electrical power to the
range at the main fuse or circuit breaker panel. Failure to do so may result in electric shock or burn.
CAUTION
BURN HAZARD:
The glass cover and bulb should be removed when cool. Touching hot glass with
bare hands or a damp cloth can cause burns.
CAUTION
Before replacing your oven light bulb, disconnect the electrical power to the range at the main fuse
or circuit breaker panel. Be sure to let the light cover and bulb cool completely.
The oven light bulb is covered with a removable glass cover that is held in place with a bail-shaped
wire. Remove the oven door, if desired, to reach the cover easily. See the Lift-Off Oven Door
section for detailed oven door removal instructions.
Replacing the Light Bulb (glass cover on self clean
models only):
2. Hold the glass cover stable, so it doesn’t fall when
released.
3. Slide near the indent of the cover holder until the
cover is released.
Do not remove any screws to
release the glass cover.
bulb.
Do not touch hot bulb with hand or wet
cloth. Only remove bulb when it is cool.
5. Hold glass cover stable over new bulb.
indent in the wire cover holder is located in the indent
of the glass cover.
7. Connect electrical power to range.
Wire cover holder
Indent