Icom IC-9100 Instruction Manual

Icom IC-9100 Manual

Get Icom IC-9100 PDF manuals and user guides View all Icom IC-9100 manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-9100 manual content summary:

  • Icom IC-9100 | Instruction Manual - Page 1
    INSTRUCTION MANUAL HF/VHF/UHF TRANSCEIVER i9100
  • Icom IC-9100 | Instruction Manual - Page 2
    agree with Icom's philosophy of "technology first." Many hours of research and development went into the design of your IC-9100. FEATURES ❍ The IC-9100 fully covers HF to 1200 MHz*1 multiband in one transceiver ❍ Independent dual receivers in one radio; receives two different bands simultaneously
  • Icom IC-9100 | Instruction Manual - Page 3
    level, otherwise, the linear amplifier will be damaged. BE CAREFUL! The transceiver will become hot when operating the transceiver continuously for long periods of time. USE only the specified microphone. Other manufacturers' microphones have different pin assignments, and connection to the IC-9100
  • Icom IC-9100 | Instruction Manual - Page 4
    and automatically program their radio for a reply. Like other communication modes, you can operate simplex D-STAR with other hams, for direct communication. See pages 85 to 120 for the D-STAR operation details. NOTE: The optional UT-121 is required for the DSTAR operation with the IC-9100. • D-STAR
  • Icom IC-9100 | Instruction Manual - Page 5
    10 GHz microwave link. Areas 1 to 4 and 5 to 8 make up a zone in the example above. Gateway repeater: Gateway repeaters provide communications between different zones via the internet. Repeater 3 and 6 are gateway repeaters at the example above. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
  • Icom IC-9100 | Instruction Manual - Page 6
    Electronic keyer and IC-PW1/PW1EURO........... 28 D Connecting a non-Icom linear amplifier....... 29 ■ External antenna tuner memory mode 34 ■ Selecting a frequency band 35 D Using the band band operation (only USA version 40 D Band edge warning beep 41 D Programming the user band
  • Icom IC-9100 | Instruction Manual - Page 7
    function 78 D Memory keyer send menu 51 D Using the VOX function 78 D Editing a memory keyer 52 D Adjusting the VOX function 78 D Contest number Set mode 53 ■ Break-in function 79 D Keyer Set mode 54 D Semi Break-in operation 79 ■ Operating RTTY (FSK 56 D Full
  • Icom IC-9100 | Instruction Manual - Page 8
    ■ Message operation 111 D TX message programming 111 D Message Transmission 112 D RX message display 112 ■ DV automatic detection 113 ■ Automatic Reply function 113 ■ Digital squelch functions 114 ■ EMR communication 115 D Adjusting the EMR AF level 115 ■ BK mode communication
  • Icom IC-9100 | Instruction Manual - Page 9
    CPU 181 D Satellite memory programming 155 D Partial reset 181 2 ■ Preparation 156 D All reset 181 ■ Satellite operation 157 ■ Data cloning 182 3 D Cloning between transceivers 182 13 ANTENNA TUNER OPERATION 158-160 D Cloning using a personal computer........... 182
  • Icom IC-9100 | Instruction Manual - Page 10
    to manually start the an- • Y ou can reverse the keyer paddle polarity (dot and tenna tuner. • If the tuner cannot tune the antenna within 20 sec- onds, the tuning circuit is automatically bypassed. dash) in the "Paddle Polarity" item of the Keyer Set mode. (p. 55) • Four keyer memory channels
  • Icom IC-9100 | Instruction Manual - Page 11
    ; p. 45) Rotate to adjust audio output level to the speaker or headphones on the MAIN Band. Increases • T he squelch is particularly effective for AM and FM, but also works in other modes. • T he 12 to 1 o'clock position is recommended for the most effective use of the [RF/SQL] control. • [RF
  • Icom IC-9100 | Instruction Manual - Page 12
    the noise reduction function is in use. Set for maximum readability. • To use this control, first push [NR] (!5). Increases !8 S UB BAND AF CONTROL [AF] (inner control; p. 45) Rotate to adjust audio output level to the speaker or headphones on the SUB Band. !9 MIC GAIN CONTROL [MIC GAIN] (p. 46
  • Icom IC-9100 | Instruction Manual - Page 13
    keyer to between 6 wpm (minimum) and 48 wpm (maximum). Slow Fast @3 P REAMP•ATTENUATOR SWITCH [P.AMP•ATT] PREAMP SWITCH Operation (p. 71) (Frequency band: HF function? The break-in function automatically switches between transmit and receive with your CW keying. Using Full break-in function (QSK
  • Icom IC-9100 | Instruction Manual - Page 14
    SW" item is set to ➥ Hold down for 1 second to select the DR mode. "ON" in the Set mode. (p. 164) • " " appears. [SSB] (p. 47) ➥ Push to alternately select the USB or LSB modes. ➥ In the DR mode, push to cancel it. • " " disappears. • "USB" or "LSB" appears. ➥ In the SSB mode, hold down for
  • Icom IC-9100 | Instruction Manual - Page 15
    the transceiver to the satellite mode. If you want to operate in the DR mode after exiting the satellite mode, you must hold down [DV•DR] for 1 second. ➥ Hold down for 1 second to transfer the uplink and downlink frequencies into the satellite VFO. • T he satellite mode is automatically
  • Icom IC-9100 | Instruction Manual - Page 16
    the memory channel. • The channel becomes a blank channel. • This switch is disabled in the VFO mode. $3 T UNING STEP•REPEATER GROUP SWITCH [TS•GRP] TUNING STEP SWITCH Operation (p. 38) ➥ Push to toggle between the kHz and MHz* quick tuning step, or turn OFF the quick tuning. * When the HF/50
  • Icom IC-9100 | Instruction Manual - Page 17
    ; p. 139) Select a memory channel. • Rotate clockwise to select a higher memory channel number; rotate counterclockwise to select a lower memory channel number. Higher channel Lower channel $9 RIT SWITCH [RIT] (p. 69) ➥ P ush to turn the RIT function ON or OFF. • Use [RIT/∂TX] control to vary the
  • Icom IC-9100 | Instruction Manual - Page 18
    45) ➥ P ush to audibly announce the S-meter level, the displayed frequency and the operating mode. • The S-Level announcement can be turned OFF in the "SPEECH S-Level" item of the Set mode. (p. 164) • W hen RIT and/or ∂TX are ON, the RIT/∂TX offset is not included in the frequency announcement
  • Icom IC-9100 | Instruction Manual - Page 19
    ø antenna with a type-N connector for the 430 MHz frequency band. 6 nector for the HF/50 MHz frequency band. u 1 44 MHz ANTENNA CONNECTOR [144MHz ANT] 7 When using an optional AH-4 hf/50 mhz auto- (pp. 24, 25, 158) matic antenna tuner, connect it to the [ANT1] Connect a 50 ø antenna with
  • Icom IC-9100 | Instruction Manual - Page 20
    CT-17 ci-v level converter, for external control of the transceiver. ➥ Use for transceive function with another Icom CI-V transceiver or receiver. When the transceive function is set to ON, changing the frequency, operating mode, etc. on the IC-9100 automatically changes those settings on
  • Icom IC-9100 | Instruction Manual - Page 21
    separately) • P C software (such as optional RS-BA1 or CS- 9100) NEVER connect the transceiver to a PC until the USB driver installation has been completed. About the modulation input: Select "USB" in the Set mode item "DATA OFF MOD" or "DATA MOD." The modulation input level from the USB jack can
  • Icom IC-9100 | Instruction Manual - Page 22
    --- --- FSKK Controls RTTY keying "High" level "Low" level Output current : More than 2.4 V : Less than 0.6 V : Less than 2 mA MOD Modulator input. Input impedance Input level : 10 k˘ : Approx. 100 mV rms AF*3 AF detector output. Output impedance : 4.7 k˘ Fixed level, regardless control
  • Icom IC-9100 | Instruction Manual - Page 23
    6 7 q FSKK w GND e HSEND r MOD t AF y SQLS u 13.8 V i ALC ACC 2 4 25 1 3 6 7 q 8 V w GND e HSEND r BAND t ALC y VSEND u 13.8 V D DATA2 Output impedance eration only. Output level : 4.7 k˘ : 100-300 mV rms SQL* Squelch out terminal. This pin is SQL open grounded when the transceiver
  • Icom IC-9100 | Instruction Manual - Page 24
    memory channel. u SELECT MEMORY CHANNEL ICON ➥ Appears when the selected memory channel is set as a select memory channel. (p. 151) ➥ Appears when the repeater can be selected as the access repeater in the DR mode. (p. 100) i DR MODE ICON (p. 43) Appears when the DR mode is selected. o RIT/∂TX
  • Icom IC-9100 | Instruction Manual - Page 25
    !9 @0 !5 !3 TONE SQUELCH ICONS (Mode: FM) ➥ "T" appears when the repeater tone function is ON. (p. 65) ➥ "TSQL" appears when the tone squelch function frequencies simultaneously increase or decrease in the same step. : Reverse satellite mode is selected. • W hen [MAIN DIAL] is rotated clockwise
  • Icom IC-9100 | Instruction Manual - Page 26
    , " " for AGC fast is fixed. @4 PREAMP ICON (p. 71) Appears when a preamplifier is turned ON. • In HF/50 MHz frequency band, either "P. AMP " or "P. AMP receiver, which is connected to the [DATA1] jack, is output to the [USB] port. @6 GPS TX ICON (p. 134) ➥ "GPS" appears when the GPS transmission
  • Icom IC-9100 | Instruction Manual - Page 27
    ICONS (p. 77) (Mode: SSB/CW/RTTY/AM) ➥ "MNF" appears when the Manual Notch function is turned ON. (Mode: SSB/AM/FM) ➥ "ANF" appears when the Automatic Notch function is turned ON. #5 ATTENUATOR ICON (p. 71) Appears when the Attenuator function is turned ON. #6 MEMORY ICON (pp. 34, 139) Appears
  • Icom IC-9100 | Instruction Manual - Page 28
    M3 (menu 3) display can be selected after selecting menu 2. • In the DR mode, the D1 and D2 displays can be selected. D M1 (Menu 1) DUP 1 ⁄ 4 SCP (Mode: CW) AGC DUP 1 ⁄ 4 KEY SCP (Mode: RTTY) AGC DUP 1 ⁄ 4 RTTY SCP D M3 (Menu 3) display (Mode: DV) CS CD R>CS UR DSET D D1
  • Icom IC-9100 | Instruction Manual - Page 29
    FM mode, hold down for 1 second to turn the one-touch repeater function ON or OFF. SPEECH COMPRESSOR KEY [COMP](F-3) (p. 80) memory keyer) or the "SEND" screen (keyer send), depending on the "KEYER 1st Menu" option in the Set mode (p. 165). RTTY MENU KEY [RTTY](F-4) (p. 57) Push to display the "RTTY
  • Icom IC-9100 | Instruction Manual - Page 30
    [CD](F-2) (p. 95) Push to display the "CD" screen. • The call record channel appears. (RX01 to RX20) R>CS KEY [R>CS](F-3) (p. 96) Hold down for ](F-4) (p. 101) Push to display the "UR" screen. • The desired station or repeater call sign can be selected. DSET KEY [DSET](F-5) (p. 118) Push to enter the
  • Icom IC-9100 | Instruction Manual - Page 31
    TV sets, TV antenna ele- lems, ground the transceiver using the GROUND ter- ments, radios and other electromagnetic sources. minal on the rear panel . However, "Straight 14 key" must be selected in the "Keyer Type" item of the Keyer HM-36 SM-50 SM-30 15 Set mode. (p. 55) (Option) (Option)
  • Icom IC-9100 | Instruction Manual - Page 32
    SWR is higher than approximately 2.0:1, the transceiver automatically reduces the TX power to protect the final transistors. In that case, an antenna tuner is useful to match the transceiver and antenna. Low SWR allows full power for transmitting. The IC-9100 has an SWR meter to continuously monitor
  • Icom IC-9100 | Instruction Manual - Page 33
    connections D Rear panel DC POWER SUPPLY (p. 27) PS-126 [144MHz ANT] (p. 158) HF/50MHz ANTENNA 1, 2 (p. 158) Connection example: [ANT1] for 1.8-18 MHz bands antenna [ANT2] for 21-28 MHz bands antenna GROUND (p. 22) Use the heaviest possible gauge wire or strap and make the connection as short as
  • Icom IC-9100 | Instruction Manual - Page 34
    AND CONNECTIONS ■ Advanced connections D Front panel HEADPHONES MIC The AFSK modulation signal can also be input to [MIC]. (p. 171) D Rear SWR meter, or other device between the transceiver and preamplifier. [ALC], [SEND] (p. 29) Used for connecting a non-Icom linear amplifier. [ANT1], [ANT2] (
  • Icom IC-9100 | Instruction Manual - Page 35
    for keyer memory control. When using a external keypad, select "KEYER SEND" connections REMOTE JACK, USB CONNECTOR (p. 183) Used for computer control and transceive operation. The using a PC and the transceiver, or for the GPS receiver connection. A third-party serial data communication software is
  • Icom IC-9100 | Instruction Manual - Page 36
    [POWER] switch is OFF. • Output voltage of the power source is 12 to 15 V when you use a non-Icom power supply. • DC power cable AC cable DC power cable Ground Transceiver D Connecting a non-Icom DC POWER SUPPLY Transceiver For European versions Transceiver AC outlet Ground A DC power
  • Icom IC-9100 | Instruction Manual - Page 37
    ] PW1EURO) Coaxial cable* OPC-599 [INPUT2] [ANT1] [ACC] [ANT2] [REMOTE] [GND] [GND] IC-PW1/EURO AC outlet Ground (Non-European versions: 100-120/200-240 V European version : 230 V) Transceiver *Purchase separately, and connect to [INPUT2], if necessary. 1 2 3 4 5 6 7 8 9 10 11 12 13
  • Icom IC-9100 | Instruction Manual - Page 38
    ALC output level after referring to the linear amplifier instruction manual. • T he ALC input level must be in the range 0 V to -3 V. The transceiver does not accept a positive voltage. Nonmatched ALC and RF power settings could overheat or damage the linear amplifier. • T he IC-9100 SEND
  • Icom IC-9100 | Instruction Manual - Page 39
    [XFC], push to change the transmit frequency. • The [UP]/[DN] switch can be used as a key paddle if the "MIC Up/Down Keyer" item setting is "ON" in the Keyer Set mode. In such case, the frequency and memory channel cannot be changed using the [UP]/[DN] switches. (p. 55) • Y ou can set the dot-dash
  • Icom IC-9100 | Instruction Manual - Page 40
    sure all connections required for your system are complete by reviewing them in Section 2 of this manual. [NOTCH] [RF/SQL] : 12 o'clock : ON (Partial resetting) First time to Power ON: Reset the transceiver using the following procedure. A partial resetting CLEARS the operating parameters to their
  • Icom IC-9100 | Instruction Manual - Page 41
    within the HF/50MHz band, the SUB Band can simultaneously receive on only the 144 MHz, 430 MHz and 1200 MHz* frequency bands, or visa versa. *The optional UX-9100 is required for the 1200 MHz frequency band operation. Both MAIN and SUB Bands have independent features. MAIN Band : Used for both
  • Icom IC-9100 | Instruction Manual - Page 42
    , tuning, operating mode selection, memory channel selection and programming, are made for the MAIN Band. When the SUB Band setting mode is ON, the settings and selections are for only the SUB Band. • You cannot transmit on the SUB Band. • You cannot make Main Band settings. ➥ Push [SUB] to
  • Icom IC-9100 | Instruction Manual - Page 43
    IC-9100 has two VFOs; "A" and "B," for each MAIN and SUB Bands, and are convenient for quickly selecting two frequencies, or split frequency operation. You can use COMP TBW SCP M1 AGC DUP COMP TBW SCP [VFO/MEMO] Memory icon M1 Memory channel number AGC DUP COMP TBW SCP 1 2 3 4 5 6 7 8 9 10
  • Icom IC-9100 | Instruction Manual - Page 44
    Selecting a frequency band The frequency band you want to use can be selected in the MAIN and SUB Bands. Before changing the frequency band on the SUB Band, push [SUB] to turn ON the SUB Band setting mode. In addition to the HF/50 MHz, 144 MHz and 430 MHz frequency bands, the IC-9100 can operate on
  • Icom IC-9100 | Instruction Manual - Page 45
    down AGC DUP COMP TBW SCP Push M1 AGC DUP COMP TBW SCP Push M1 AGC DUP COMP TBW SCP The optional UX-9100 is required for 1200 MHz frequency band operation. Push M1 AGC DUP COMP TBW SCP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 36
  • Icom IC-9100 | Instruction Manual - Page 46
    select the transceiver's frequency by using [MAIN DIAL], or you can enter it using the keypad. D Tuning with [MAIN DIAL] q S elect the desired frequency band. • Hold down [BAND](MAIN/SUB) for 1 second one or more times until the desired frequency band is displayed. • Push the desired band key on
  • Icom IC-9100 | Instruction Manual - Page 47
    'kHz' quick tuning is selected, the frequency can be changed in the selected 'kHz' steps. The MAIN and SUB Bands use the common 'kHz' tuning step. You can select it in both Band's. q P ush [TS] to turn ON the Quick Tuning function. • "Z" appears. w H old down [TS] for 1 second to display the "TS
  • Icom IC-9100 | Instruction Manual - Page 48
    and/or ∂TX are used, they also tune used for frequency tuning (if the quick tuning function is not selected.) D Auto tuning step function When you rotate [MAIN DIAL] rapidly, the tuning speed can automatically (Mode: SSB-D/CW/RTTY) The dial speed is operating frequency band. This function
  • Icom IC-9100 | Instruction Manual - Page 49
    shown in the table above. 3 *The FCC specifies center frequencies on the 5 MHz band. However, the IC-9100 displays carrier 4 frequency. Therefore, tune the transceiver to 1.5 kHz below the specified FCC channel center 5 frequency. 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
  • Icom IC-9100 | Instruction Manual - Page 50
    Set mode. The beep output level can be set in the "Beep Level" item of the Set mode. (p. 161) About the user band edge frequencies When "ON (User)" or "ON (User) & TX" is selected in the "Band Edge Beep" item, a total of 30 band edge frequencies can be programmed in the "User Band Edge" item. See
  • Icom IC-9100 | Instruction Manual - Page 51
    3 BASIC OPERATION D Programming the user band edge When "ON (User)" or "ON (User) & TX" is selected in the "Band Edge Beep" item, the "User Band Edge" item appears in the Set mode. A total of 30 band edge frequencies can be programmed in the "User Band Edge" item. NOTE: • All frequency ranges are
  • Icom IC-9100 | Instruction Manual - Page 52
    both Bands, the transceiver cannot receive on the SUB Band. receiver. ➥ Hold down [DV•DR] to turn the DR (D-STAR® Repeater) mode operation ON or OFF. • "DV" and " " appears. • T he DV mode is automatically selected when the DR mode is ON. • D R (D-STAR Repeater) mode allows you to use a re
  • Icom IC-9100 | Instruction Manual - Page 53
    receive (RF) sensitivity Adjusts the RF gain and squelch threshold level. The squelch removes noise output to the speaker when no signal is received (closed squelch). • T he squelch is particularly effective for AM and FM, but can also be used in other modes. • T he 12 to 1 o'clock position is
  • Icom IC-9100 | Instruction Manual - Page 54
    OPERATION ■ Volume setting ➥ Rotate the [AF] control clockwise to increase the audio output level, counterclockwise to decrease it. Increases [AF] ."*/#BOE Decreases ■ Voice synthesizer operation The IC-9100 has a built-in voice synthesizer to announce the operating frequency, mode and S-meter
  • Icom IC-9100 | Instruction Manual - Page 55
    for Icom microphones Decreases Increases e R elease [PTT] to receive. [TRANSMIT] MAIN Band TX/RX indicator 1 2 3 [RF POWER] SUB Band TX/RX indicator 4 NOTE: When you transmit on the HF/50 MHz fre- 5 quency bands, while monitoring an out of the ama- teur band frequency on VHF or UHF on
  • Icom IC-9100 | Instruction Manual - Page 56
    tuning step can be changed using the tuning step program mode. (p. 38) r R otate [AF] (MAIN Band) to adjust the audio to a comfortable listening level. t P ush [PTT] on the microphone to transmit. (or [TRANSMIT] on the transceiver) • The TX/RX indicator (MAIN Band) lights red. y S peak into the
  • Icom IC-9100 | Instruction Manual - Page 57
    . • The tuning step can be changed using the tuning step program mode. (p. 38) r R otate [AF] (MAIN Band) to adjust the audio to a comfortable listening level. t Push [TRANSMIT] to transmit. • The TX/RX indicator (MAIN Band) lights red. y U se the electric keyer or paddle to key your CW signals
  • Icom IC-9100 | Instruction Manual - Page 58
    USB modes. Use when interfering signals are near a desired signal and you want to reduce the interfering tone. q Push [CW/RTTY] once or twice to select the CW mode. w Hold down [CW/RTTY Hz steps) D About keying speed The transceiver's internal electronic keyer speed can be adjusted to between 6 and
  • Icom IC-9100 | Instruction Manual - Page 59
    ) SEND M1 M2 M3 M4 001 -1 • Memory Keyer screen KEY SEND EDT 001 SET • Keyer Edit screen (p. 52) [F-3] EDT CQ TEST CQ TEST DE M1 Ω ≈ DEL SPC [F-2] • Contest Number Set mode (p. 53) [F-4] 001 Number Style ∫1 √ Normal • Keyer Set mode (p. 54) [F-5] SET Side Tone Level ∫1 √ 50
  • Icom IC-9100 | Instruction Manual - Page 60
    Send). r P ush [TRANSMIT] to switch the transceiver to transmit, or turn ON the Break-in function. (p. 79) t P ush one of the function keys, [M1](F-1) to [M4](F-4), to send the memory keyer contents. • Holding down a function key for 1 second repeatedly sends the contents; push any function key
  • Icom IC-9100 | Instruction Manual - Page 61
    "ar" is sent with no space. "✱" is used to insert the CW contest number. The number automatically advances by 1. This function is available for only one memory keyer channel at a time. "✱" is used in memory keyer channel M2 by default. EDT CQ TEST CQ TEST DE M1 Ω ≈ DEL SPC Input a space Delete
  • Icom IC-9100 | Instruction Manual - Page 62
    , if desired. y Push [MENU] to save, and return to the "KEY" screen (Memory Keyer). u P ush [MENU] to return to the "M1" screen (Menu 1). 1. Number Style (Default: Normal) This item sets the numbering system used for contest numbers- normal or short morse numbers. Short morse numbers are also
  • Icom IC-9100 | Instruction Manual - Page 63
    4 RECEIVE AND TRANSMIT D Keyer Set mode This Set mode is used to set the CW sidetone, memory keyer repeat time, dash weight, paddle specifications, keyer type, etc. • Setting contents q In the CW mode, push [MENU] to display the "M1" screen (Menu 1). w P ush [KEY](F-4) to display the "KEY" screen
  • Icom IC-9100 | Instruction Manual - Page 64
    be selected. 9. MIC Up/Down Keyer (Default: OFF) Set the microphone [UP]/[DN] switches to be used as a key. (The microphone used as a key for CW. • OFF : The [UP]/[DN] switches cannot be used as a key for CW. NOTE: When "ON" is selected, the frequency and memory channels cannot be changed using
  • Icom IC-9100 | Instruction Manual - Page 65
    tuning step can be changed using the tuning step program mode. (p. 38) r P ush [TRANSMIT] to set the transceiver to the transmit mode, or transmit a SEND signal from your TNC. • The TX/RX indicator (MAIN Band) lights red. • T he Po meter displays the transmitted RTTY signal strength. t U se your
  • Icom IC-9100 | Instruction Manual - Page 66
    diagram below. • Push [MENU] to return to the previous display. D Construction of RTTY menu [DEC] [RTTY]/[TPF] [SET] [MENU] [CW/RTTY] M1 AGC DUP 1/4 RTTY S C P • RTTY screen RTTY DEC Push TPF SET • RTTY Decoder screen (p. 59) [F-2] DEC 45BPS BAUDOT MK ⁄ SFT 2125 ⁄ 170 A D J H F2 : HOLD
  • Icom IC-9100 | Instruction Manual - Page 67
    previous display. NOTE: When the Twin Peak Filter is in use, the received audio output may increase. This is normal; not a malfunction. Normal 170 Hz 2125 Hz Reverse 2125 Hz 170 Hz Space Mark BFO BFO Space Mark RTTY DEC TPF SET Push RTTY RTTY-TPF ON DEC TPF SET Appears when the Twin Peak
  • Icom IC-9100 | Instruction Manual - Page 68
    when no signal is received, adjust the RTTY decoder threshold level. q Select the RTTY decoder screen as described above. w P ush [F-1](ADJ) to select the threshold level adjustment mode. e Rotate [MAIN DIAL] to adjust the RTTY decoder threshold level. • Hold down [F-3] for 1 second to reset to
  • Icom IC-9100 | Instruction Manual - Page 69
    4 RECEIVE AND TRANSMIT D RTTY Set mode The RTTY Set mode is used to set the mark and shift frequencies, keying type, decode USOS function, RTTY decoder new line code and the number of decode screen display lines. • Setting contents q In the RTTY mode, push [MENU] to display the "M1" screen (
  • Icom IC-9100 | Instruction Manual - Page 70
    can be changed in the tuning step program mode. (p. 38) r R otate [AF] (MAIN Band) to adjust the audio to a comfortable listening level. t P ush [PTT] on the microphone to transmit. (or [TRANSMIT] on the transceiver) • The TX/RX indicator (MAIN Band) lights red. y S peak into the microphone at
  • Icom IC-9100 | Instruction Manual - Page 71
    Tone squelch operation The tone squelch opens only when you receive a signal containing a matching subaudible tone. You can silently wait for calls from others using the same tone. q Push [AM/FM] once or twice to select the FM mode. w P ush [MENU] to display the "M1" screen (Menu 1). e P ush [TON
  • Icom IC-9100 | Instruction Manual - Page 72
    for both transmit and receive. NR : Normal polarity is used for transmit, reversed polarity is used for receive. RN : Reversed polarity is used for transmit, normal polarity is used for receive. RR : Reversed polarity is used for both transmit and receive. • Hold down [F-3] for 1 second to reset
  • Icom IC-9100 | Instruction Manual - Page 73
    more times to select the tone type to be scanned. • "Rptr Tone" for a repeater tone, "TSQL Tone" for tone squelch or "DTCS Code" for a DTCS code scan or DTCS code scan is used in the Memory or Call channel mode, the detected tone frequency or code can be used temporarily. To save the detected tone
  • Icom IC-9100 | Instruction Manual - Page 74
    receive frequency by a frequency offset. A repeater can be accessed using the duplex operation to set the frequency shift to the same value as the repeater's frequency offset. See page 94 for details on accessing a D-STAR® repeater. q Select the desired frequency band. (p. 35) w Push [VFO/MEMO] to
  • Icom IC-9100 | Instruction Manual - Page 75
    , set the frequency offset as well as the repeater access tone frequency (p. 163). q Select the desired frequency band. (p. 35) w In the FM mode, push [A/B] to select VFO A. e R otate [MAIN DIAL] to set the desired receive fre- quency (repeater output frequency). r P ush [MENU] to display the "M1
  • Icom IC-9100 | Instruction Manual - Page 76
    and Korea versions only) The transceiver has three Auto Repeater ranges that can be used for each frequency band. And you can set the desired Auto Repeater ranges by programming the lower and higher edge frequencies into the allowable Memory channel of each band as described below. [POWER] [AM
  • Icom IC-9100 | Instruction Manual - Page 77
    falls within the repeater output frequency range, the Auto Repeater function automatically sets the repeater settings (duplex is selected. !0 H old down [MW] for 1 second to store the set contents into the selected memory channel. [∫] [√] [MENU] [MAIN DIAL] SET A u t o R e p e a t e r Ù 20 Ú
  • Icom IC-9100 | Instruction Manual - Page 78
    Automatic Frequency Control. The AFC function tunes the displayed frequency automatically when an off-center frequency is received. q Push [AM/FM] or [DV•DR] in 10 Hz steps*, without changing the transmit frequency. *The [RIT/∂TX] control tunes in 1 Hz steps when the operating frequency readout is
  • Icom IC-9100 | Instruction Manual - Page 79
    and strength of signals around a specified frequency. The IC-9100's Band Scope function can be used in any operating mode and any frequency band. Blinks when the reference frequency is outside of the sweep range. SCP Sweep icon Band scope display Frequency display mark Sweep step display STEP
  • Icom IC-9100 | Instruction Manual - Page 80
    430 or 1200 MHz*2 frequency band. • Be sure to set the "EXT-P.AMP" item for each frequency band in the Set mode. (pp. 165, 166) (Frequency band: HF/50 MHz) ➥ Push [P. , but it can be still be used. *2 The optional UX-9100 is required for 1200 MHz frequency band operation. [P.AMP•ATT] About the
  • Icom IC-9100 | Instruction Manual - Page 81
    output level, even when the received signal strength varies greatly. The transceiver has 3 pre-set AGC time constants: fast, mid and slow for SSB, CW, RTTY mode (except for FM and DV), then repeat steps e and r, if desired. y P 2.5, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0 Fixed [MENU] [AGC] M1 AGC DUP COMP
  • Icom IC-9100 | Instruction Manual - Page 82
    transceiver has 3 passband width IF filters for each mode. The filter selection is automatically memorized in each mode. The PBT shift frequencies are automatically Repeat Hz) RTTY FILTER1 (2.4 Fixed FILTER3 (7.0 kHz)* * When FILTER2 or FILTER3 is selected in the FM mode, the 73 TX modulation
  • Icom IC-9100 | Instruction Manual - Page 83
    IF filter selection (Mode: SSB/CW/RTTY/AM) The IC-9100 has a 15 kHz filter passband width at the 1st IF frequency. The 1st IF filters reduce interference from strong nearby signals. If the optional FL-430 1st if filter (6 khz) is installed, a 6 kHz filter width can be used. Or, if the FL-431
  • Icom IC-9100 | Instruction Manual - Page 84
    5 FUNCTIONS FOR RECEIVE ■ Twin PBT operation (Mode: SSB/CW/RTTY/AM) To reject interference, PBT (Passband Tuning) electronically narrows the IF passband width by shifting the IF frequency slightly outside of the IF filter passband. The IC-9100 uses DSP for the PBT function. Moving both [TWIN-PBT]
  • Icom IC-9100 | Instruction Manual - Page 85
    RTTY/AM) The Noise Blanker eliminates pulse-type noise such as noise from car ignitions. ➥ Push [NB] to turn the Noise Blanker function ON or OFF. • "NB" is displayed when the Noise Blanker is ON. When using Set mode, the peak level of a received signal strength or the output power is displayed for
  • Icom IC-9100 | Instruction Manual - Page 86
    • "NR" appears. w R otate the [NR] control to adjust the noise reduction level. e P ush [NR] to turn OFF the Noise Reduction. • "NR" disappears. /FM Manual notch : SSB/CW/RTTY/AM) This transceiver has Auto and Manual Notch functions. The Auto Notch function uses DSP to automatically attenuate
  • Icom IC-9100 | Instruction Manual - Page 87
    to the point where the transceiver is continuously transmitting. t If the receive audio from the speaker causes the VOX circuit to OFF, Short, Mid and Long settings can be set. When using the VOX voice delay, turn OFF the TX monitor function to prevent transmitted audio from being echoed. 1 2
  • Icom IC-9100 | Instruction Manual - Page 88
    ■ Break-in function (Mode: CW) The Break-in function is used in the CW mode to automatically toggle the transceiver between transmit and receive when keying. The IC-9100 is capable of Full Break-in or Semi Break-in. [MENU] [CW/RTTY] D Semi Break-in operation During Semi Break-in operation, the
  • Icom IC-9100 | Instruction Manual - Page 89
    function increases average RF output power, improving signal strength and readability. q Push [SSB] to select the USB or LSB mode. w the default set- ting, if desired. When the COMP meter peaks above the COMP level zone, your transmitted voice may be distorted. y Push [MENU] to return to the
  • Icom IC-9100 | Instruction Manual - Page 90
    ∂TX frequency offset). ■ Monitor function The Monitor function allows you to monitor your transmit IF signals in any mode. Use " screen (Monitor). e Rotate [MAIN DIAL] to adjust the monitor level. • For the clearest audio output, adjust while holding down [PTT] and speaking into the microphone. •
  • Icom IC-9100 | Instruction Manual - Page 91
    you to transmit and receive on two different frequencies. Split frequency operation is performed using frequencies in VFO A and VFO B. • T he Split frequency operation is automatically turned OFF when turning ON the One-touch repeater function. The following is an example of setting 21.290 MHz for
  • Icom IC-9100 | Instruction Manual - Page 92
    VFO is automatically changed according to the plus/ minus frequency shift programmed in the Set B frequencies. q S uppose you are operating at 21.290 MHz (USB) in VFO A. w Hold down [SPLIT] for 1 second. • When the Split Lock function is not used, accidentally releasing [XFC] while rotating
  • Icom IC-9100 | Instruction Manual - Page 93
    TRANSMIT ■ Measuring SWR (Band: HF/50/144/430 MHz) The IC-9100 has a built-in circuit for measuring antenna SWR- no external equipment or special adjustments are necessary. The IC-9100 can measure SWR two ways- spot measurement and plot measurement. D Spot measurement q P ush [TUNER] once or twice
  • Icom IC-9100 | Instruction Manual - Page 94
    signs in the call sign memory. Up to 500 repeater call signs can be stored in the repeater list. D "MY" (Your own call sign) programming Your own call sign must be programmed for both digital voice and low-speed data communications (including GPS transmission). q Push [DV•DR] to select the DV mode
  • Icom IC-9100 | Instruction Manual - Page 95
    the "CS" screen. ✔ For your information The IC-9100 has a call sign edit record function. When you edit a call sign that is stored in a call sign memory, the edited call sign is automatically programmed into a blank channel. If all call sign memories are already programmed, the edited call sign will
  • Icom IC-9100 | Instruction Manual - Page 96
    u to enter a desired repeater call sign. • A call sign of up to 8 digits can be set. o P ush [MENU] to store the programmed call sign. !0 Push [MENU] again to return to the "CS" screen. [MENU] [DVɾDR] [MAIN DIAL] M3 CS C D R > C S U R DSET CS UR CQCQCQ Ú MY R1 R2 NOT USE R1 ≈ Ú CLR R1
  • Icom IC-9100 | Instruction Manual - Page 97
    to 500 repeater memory channels (Repeater list) in up to 10 Groups. Programming the repeater list is required for DR mode operation. The outline of the repeater list is as follows: q Adding new repeaters or editing a list w Selecting a repeater to edit e P rogramming repeater data (Repeater name
  • Icom IC-9100 | Instruction Manual - Page 98
    (port), according to the repeater frequency, as shown below. Note that Japanese repeater node letters are different. • 1200 MHz : A (B in Japan) • 430 MHz : B (A in Japan) • 144 MHz : C (no D-STAR repeaters in Japan) Cross band operation between different nodes in the same repeater area can be made
  • Icom IC-9100 | Instruction Manual - Page 99
    . Ù Ú CLR EDT 9 10 11 12 @3 P ush [MENU] to save the programmed call sign. @9 P ush [EDT](F-4) to enter the frequency program- 13 5. Repeater group programming ming mode. • A cursor appears and blinks. 14 The IC-9100 has a total of 10 groups (0-9). You can assign and organize up to 500
  • Icom IC-9100 | Instruction Manual - Page 100
    the entry, and return to the RP-L screen. ■ Editing a repeater list This function re-programs a repeater's data. This is useful when already-programmed data is incorrect or some data should be added to the list. 1. Repeater list selection q Push [DV•DR] to select the DV mode. w P ush [MENU] one
  • Icom IC-9100 | Instruction Manual - Page 101
    a repeater list 3. After programming Contents of programmed list can be cleared (erased). To add the programmed data as a new list: !0 P ush [Z](F-2) to select the "ADD Write" item, then hold down [WR](F-5) for 1 second. • "ADD Write OK?" appears. RP-L ADD W r i t e Ù Ú WR q Push [DV•DR] to
  • Icom IC-9100 | Instruction Manual - Page 102
    in front of the repeater call sign. The repeater call sign with '/' is used for the gateway CQ calling. *2 For an area (local) repeater communication only (Link repeater is not used.) *3 [GRP](F-5) is not used in the DR mode. 93 About the Time-Out Timer function The IC-9100 has a Time-Out Timer
  • Icom IC-9100 | Instruction Manual - Page 103
    the offset to the desired direction. • "DUP-" or "DUP+" appears. • W hen the Auto Repeater function is in use, this selec- tion is not necessary (Only U.S.A. and Korean versions). (p. 67) i Push [DV•DR] to select the DV mode. (p. 43) • "DV" appears. • "T" disappears. o W hen a signal is received
  • Icom IC-9100 | Instruction Manual - Page 104
    in the DV mode, the calling station and repeater call signs being used can be stored in the received call record. The stored call signs can be displayed in the following manner. Up to 20 calls can be stored. D Desired call record display q Push [DV•DR] to select the DV mode. w P ush [MENU
  • Icom IC-9100 | Instruction Manual - Page 105
    DV Set 15 mode. These functions are not available in the DR mode. • "RX Call Sign Write" item (p. 118): 16 The calling station's call sign is automatically set to "UR." 17 • "RX RPT Write" item (p. 119): The repeater call signs are automatically set to "R1" 18 and "R2," if necessary. 19
  • Icom IC-9100 | Instruction Manual - Page 106
    [SET](F-5) for 1 second to store or overwrite the edited call sign into the selected channel. 97 [√] [CD] [CLR] [MENU] [DVɾDR] [MAIN DIAL] M3 CS C D R > C S U R DSET CS UR CQCQCQ Ú MY J A 3 Y U A R1 R2 NOT USE UR ≈CQCQCQ UR Ú CLR EDT NAME GRP Rotate [MAIN DIAL] UR ≈JG3YMK Ú CLR EDT
  • Icom IC-9100 | Instruction Manual - Page 107
    "RXRPT2") into call sign memory "UR" and a repeater all at the same time, or individually. u S elect the desired copy destination • AUTO : Hold down [AUTO](F-4) for 1 second to automatically search for a blank q Push [DV•DR] to select the DV mode. call sign memory channel, and copy w P ush
  • Icom IC-9100 | Instruction Manual - Page 108
    OPERATION ■ DR (D-STAR Repeater) mode operation DR (D-STAR Repeater) mode is used for D-STAR repeater operation. In this mode, you can select the pre-programmed repeaters and UR call sign by using [MAIN DIAL]. • DR mode operation flow chart Step 1: (R1 selection) Select your access repeater. - The
  • Icom IC-9100 | Instruction Manual - Page 109
    scan's target setting' as described below. q H old down [DV•DR] for 1 second to select the DR mode. • T he DV mode is automatically selected. • T he access repeater selection screen is displayed. - O nly the repeaters, specified as a scan target are displayed. w P ush [MENU] one or more
  • Icom IC-9100 | Instruction Manual - Page 110
    this guide to access a D-STAR repeater. The optional CS-9100* cloning software is helpful for programming call signs and programming the repeater list. *Cloning cable is required. q Set your own call sign (MY). (p. 85) w H old down [DV•DR] for 1 second to select the DR mode. • The last used access
  • Icom IC-9100 | Instruction Manual - Page 111
    ] to select the desired Memory channel, Call channel or Program scan edge channel. w H old down [MW] for 1 second to store the setting. [TRANSMIT] [TS•GRP] MAIN Band TX/RX indicator [MAIN DIAL] Appear D1 U R: I K O M A − 4 3 ≈ GRP3 CS C D R > C S U R DSET Repeater selection screen MW 446
  • Icom IC-9100 | Instruction Manual - Page 112
    gateway repeater is automatically set as the Link repeater, and you can make a call to a specific station through the internet. q S et your own call sign. w H old down [DV•DR] for 1 second to select the DR mode. • T he last used access repeater is displayed. - If the displayed frequency band on
  • Icom IC-9100 | Instruction Manual - Page 113
    "GW." • The pre-programmed gateway repeater is set as R2. • Only repeaters with the same gateway repeater appear. i P ush [UR](F-4) to exit the Link repeater (R2) selection mode. o P ush [PTT] on the microphone to transmit. (or [TRANSMIT] on the transceiver) • The MAIN Band TX/RX indicator lights
  • Icom IC-9100 | Instruction Manual - Page 114
    8 DV MODE OPERATION ■ Calling a specific station (Continued) D Confirming the setting q In the DR mode, push [MENU] one or more UR setting : An individual station • R2 setting : NOT USE✱ • UR setting : Destination repeater to send CQ in the same zone • R2 setting
  • Icom IC-9100 | Instruction Manual - Page 115
    this temporary programmed data into the channel. • Calling an individual station Station call signɿ JG3YMK My call signɿ JA3YUA UR UR ≈JG3YMK UR Ú CLR EDT NAME GRP [TRANSMIT] [UR]/[SET] [VFO/MEMO] MY MY ≈JA3YUA ⁄ MY1 Ú CLR EDT NAME MAIN Band [MENU] TX/RX indicator [DV•DR] [MAIN
  • Icom IC-9100 | Instruction Manual - Page 116
    . • Received call signs can be automatically stored into the received call record. See page 95 for details. After setting, rotate [M-CH] to select a memory channel, then hold down [MW] for 1 second to save this temporary programmed data into the channel. • Calling an individual station Zone
  • Icom IC-9100 | Instruction Manual - Page 117
    95 for details. After setting, rotate [M-CH] to select a memory channel, then hold down [MW] for 1 second to save this temporary programmed data into the channel. [TRANSMIT] [Z] [SET] [GRP] [VFO/MEMO] MAIN Band [MENU] TX/RX indicator [DV•DR] [MAIN DIAL] • Calling CQ in the same zone (Zone
  • Icom IC-9100 | Instruction Manual - Page 118
    for details. After setting, rotate [M-CH] to select a memory channel, then hold down [MW] for 1 second to save this temporary programmed data into the channel. 109 [TRANSMIT] [Z] [SET] [GRP] [VFO/MEMO] MAIN Band [MENU] TX/RX indicator [DV•DR] [MAIN DIAL] • Calling CQ through the gateway UR
  • Icom IC-9100 | Instruction Manual - Page 119
    ✱ CQ • UR setting : An individual station • R2 setting : NOT USE✱ • UR setting : CQCQCQ • R2 setting : Destination repeater to send CQ in the same zone CQ • UR setting : An individual station • R2
  • Icom IC-9100 | Instruction Manual - Page 120
    TX message programming The transceiver has a total of 5 message memories to store short messages to transmit during DV mode operation. Message of up to 20 characters can be programmed for each memory. q In the DV mode, push [MENU] one or more times to display the "M3" screen (Menu 3). • In the DR
  • Icom IC-9100 | Instruction Manual - Page 121
    [TRANSMIT]). • T he message is automatically transmitted every 30 sec- onds during continuous transmission. • The MAIN Band TX/RX indicator lights red. D RX message display q In the DV mode, push [MENU] one or more times to display the "M3" screen (Menu 3). • In the DR mode, push [MENU] once or
  • Icom IC-9100 | Instruction Manual - Page 122
    "DV" and "FM" icons simultaneously blink. The transceiver automatically selects the FM mode to monitor the signal, if the DV Auto Detect function is turned ON. q In the DV mode, push [MENU] one or more times to display the "M3" screen (Menu 3). • In the DR mode, push [MENU] once or twice to select
  • Icom IC-9100 | Instruction Manual - Page 123
    sign. Thus the digital call sign squelch function can be used when communicating with only one station. q Select the desired frequency band. (p. 35) w In the DV mode, push [MENU] one or more times to display the "M1" screen (Menu 1). • In the DR mode, push [MENU] once or twice to select the "D2
  • Icom IC-9100 | Instruction Manual - Page 124
    communication function is automatically turned OFF when the transceiver is turned OFF. [TRANSMIT DSET]/[SET] MAIN Band [MENU] TX/RX indicator Appears [MAIN DIAL] SET EMR ∫ 19 √ ON When the EMR communication mode is ON. D Adjusting the EMR AF level The audio output level when an EMR signal
  • Icom IC-9100 | Instruction Manual - Page 125
    the "M3" screen (Menu 3). • In the DR mode, push [MENU] once or twice to select Band [MENU] [R>CS] TX/RX indicator Appears [MAIN DIAL] SET BK ∫ 18 √ ON When the BK function is ON. NOTE: The BK function is automatically turned OFF when transceiver is turned OFF. How to use Break-in? While using
  • Icom IC-9100 | Instruction Manual - Page 126
    ollow the instructions of the data communication application software. e P ush [PTT] on the microphone to transmit the data and an audio signal. (or push [TRANSMIT] on the transceiver) • The MAIN Band TX/RX indicator lights red. • T he input data from the [DATA1] jack are automatically transmitted
  • Icom IC-9100 | Instruction Manual - Page 127
    3. DV Data TX (Default: PTT) When receiving a call addressed to your own call sign, this function automatically sets the call sign of the call- 17 For low-speed data communication, select whether to ing station into "UR." transmit the input data manually or automatically. While in the DR mode
  • Icom IC-9100 | Instruction Manual - Page 128
    : Fast) 10. Gateway Auto Set (Default: Auto) Turn the gateway automatic set function ON or OFF for calling an individual station in the DR mode. This function enables the transceiver to automatically set the pre-programmed gateway repeater in "R2." Select the scrolling speed of a message or call
  • Icom IC-9100 | Instruction Manual - Page 129
    is automatically turned OFF when the transceiver is turned OFF. 20. EMR AF Level (Default: 50%) Enter a number between 0 % (minimum) and 100 % (maximum) to set the audio output level when an EMR signal is received. When an EMR signal is received, the audio will be heard at the programmed level
  • Icom IC-9100 | Instruction Manual - Page 130
    -232C output and NMEA data format. Third-party GPS receivers connect to the [DATA1] jack of the transceiver. In ˚45.00'N ELE ft 135˚36.00'E 12:00:00 Push • GPS screen GPS POS GPM MSG SET • GPS Memory screen (p. 127) [F-2] GPM ≈ R X ALM [F-1] • GPS Message screen (p. 125) [F-3] MSG G P S
  • Icom IC-9100 | Instruction Manual - Page 131
    jack to be used for position data to select "GPS TX Mode." r transceivers (IC-2820H, IC-E2820, ID-800H, IC-91AD, IC-E91, IC-V82, IC-U82, IC-2200H, ID-1). The GSV sentence is incompatible with them. Those transceivers will not display GPS messages properly if a GSV sentence is sent from the IC-9100
  • Icom IC-9100 | Instruction Manual - Page 132
    the time*. * These items do not appear when "Manual" is selected as the "MY Po- sition" item option Memory chan- nel's latitude, longitude, direction and distance from your position, if the GPS Alarm function is set to the channel. • If the GPS Alarm function is set to all channels
  • Icom IC-9100 | Instruction Manual - Page 133
    he Memory channel number advances automatically if the next Memory channel already contains information. • 5 0 GPS Memory channel are available. D Display the Grid Locator information The Grid Locator expresses the latitude and longitude position data in a short string of characters. The IC9100 can
  • Icom IC-9100 | Instruction Manual - Page 134
    GPS message programming Enter a GPS message of up to 20 characters to be transmitted with the position data. q H old down [CALL/GPS] for 1 second to display the "GPS" screen. w P ush [MSG](F-3) to display the "MSG" screen (GPS Message). e P ush [TXM](F-1) to display the "TXM" screen (TX Message
  • Icom IC-9100 | Instruction Manual - Page 135
    9 GPS/GPS-A OPERATION D Received GPS message display q H old down [CALL/GPS] for 1 second to display the "GPS" screen. w P ush [MSG](F-3) to display the "MSG" screen (GPS Message). e P ush [RXM](F-2) to display the "RXM" screen (RX message). • Messages of up to 36 characters can be displayed.
  • Icom IC-9100 | Instruction Manual - Page 136
    memory operation The transceiver has 50 GPS memory channels to store the received position data, or other-used position data, along with an alphanumeric channel name. [GPM]/[√] D Add a GPS memory Repeat steps w through r to program a name of up to 9 characters. y Push [MENU] to save the programmed
  • Icom IC-9100 | Instruction Manual - Page 137
    • You cannot use the keypad keys. !2 P ush [Y](F-1) or [Z](F-2) to save the programmed time data, the GPS memory 1 2 3 4 5 6 7 8 9 10 • To program a bank name 11 Memory bank setting blinks. 14 !5 Repeat steps w through r of 'Name programming' on the previous page to program a bank name of
  • Icom IC-9100 | Instruction Manual - Page 138
    described on page 128. r P ush [LIST](F-1), then push [EDT](F-2) to enter the "EDT" screen (GPS Memory Edit) to edit the programed data. • "Blank" appears when no memory is programmed. To cancel the programmed data: When the "EDT" screen is selected, push [MENU] to display "Cancel OK?." Push [YES
  • Icom IC-9100 | Instruction Manual - Page 139
    when a target position comes into the alarm area. This function can be set to the caller station, all GPS Memory channels, a specified Memory bank or a specified Memory channel. q H old down [CALL/GPS] for 1 second to display the "GPS" screen. w P ush [GPM](F-2) to display the "GPM" screen (GPS
  • Icom IC-9100 | Instruction Manual - Page 140
    appears. t Push [YES](F-4) for 1 second to clear. • To cancel clearing, push [NO](F-5). y P ush [MENU] two times to return to the "GPS" screen. • Clear a desired memory channel q H old down [CALL/GPS] for 1 second to display the "GPS" screen. w P ush [GPM](F-2) to display the "GPM" screen (GPS
  • Icom IC-9100 | Instruction Manual - Page 141
    entered position data is used. However, when the GPS receiver is connected to the transceiver, this setting will automatically switch to "GPS." 8. Manual Position (Default: LAT : 0˚00.00'N LON : 0˚00.00'E) Manually enter your latitude and longitude data. The manually programmed data can be
  • Icom IC-9100 | Instruction Manual - Page 142
    a target position enters the alarm area, the GPS alarm sounds. 10. Alarm Area2 (Default: Both) When the GPS Alarm function is set to the memory channel or "RX," set the GPS alarm active range to "Both," "Extended" or "Limited." • Limited • Extended • Both : When the target position is in the
  • Icom IC-9100 | Instruction Manual - Page 143
    Manual" is selected in "My Position," the current position data will not be automatically transmitted. 12. GPS TX DSTAR✱) Enter an unproto address of up to 56 characters. The manually programmed data can be memorized. • Unproto address programming t Repeat steps w through r to program an unproto
  • Icom IC-9100 | Instruction Manual - Page 144
    the transceiver's course QTH (VHF)) Select VHF) and Other If there is no symbol you want to use, you can make a desired symbol code, as described below. • Symbol programming use any SSID. However, if you use a capital letter, it will be used your call sign. If you use a capital letter, it will be
  • Icom IC-9100 | Instruction Manual - Page 145
    it. r Push [Ω](F-2) to move the cursor backward, or push [≈](F-3) to move the cursor forward. t Repeat steps w through r to program a comment of up to 43 characters*. * 36 characters can only be programmed when "Course/ Speed" is selected in "Data Extension." y Push [MENU] to save the comment
  • Icom IC-9100 | Instruction Manual - Page 146
    elect "GPS-A" in "GPS TX Mode." (p. 134) t S et the GPS-A mode operation's items. (pp. 134- 136) D GPS-A code details In GPS-A operation, the following codes are transmitted to the PC connected to the IC-9100. GPS-A code is based on APRS® code. (APRS® : Automatic Position Reporting System) • GPS
  • Icom IC-9100 | Instruction Manual - Page 147
    . Therefore, we recommend that memory data be backed up or be saved to a PC using the optional CS-9100 cloning software. Memory Channels 1-99 1A/1b-3A/3b C Descriptions Regular Memory channels with Split frequency capability.* Program Scan Edge Memory channels with only Simplex capability. Stores
  • Icom IC-9100 | Instruction Manual - Page 148
    the Memory channel. (Blank channel) • Memory channels can also be selected using the micro- phone [UP]/[DN] keys. In such case, the blank channels are skipped. ■ Call channel selection Each frequency band has its own Call channel. Factory default frequency and operating modes are programmed
  • Icom IC-9100 | Instruction Manual - Page 149
    10 ■ Memory channel programming Memory channels can be programmed in either the VFO mode or the Memory mode. [VFO/MEMO] [MW] D Programming in the VFO mode q Push [VFO/MEMO] to select the VFO mode. w S et the desired settings into both VFO A and VFO B. ➥ Select the band using [BAND](MAIN/SUB
  • Icom IC-9100 | Instruction Manual - Page 150
    10 MEMORY OPERATION ■ Call channel programming The Call channel is programmed in the same way as the regular Memory channels are. It is convenient to program a most-often-used frequency into the Call channel for quick recall. As with Memory channels, the Call channel can also hold split frequencies,
  • Icom IC-9100 | Instruction Manual - Page 151
    Copying in the Memory mode This is useful for copying the Memory channel contents while operating in the Memory mode. When you have changed the displayed frequency, operating mode, etc. in the selected Memory channel: • Displayed data is copied. • Programmed contents in the Memory channel are not
  • Icom IC-9100 | Instruction Manual - Page 152
    CH] M2 SCAN M E M S W R TCON V S C MEM EDT ( Push 14.19500 USB ) SEL Push EDT ABC Ω ≈ DEL SPC • When programing a memory name [Ω] [≈] Keypad [F-1] [DEL][SPC] [MAIN DIAL] [EXAMPLE]: Programming "DX spot" into Memory channel 99. Character type Cursor EDT abc DX spot Ω ≈ DEL
  • Icom IC-9100 | Instruction Manual - Page 153
    OPERATION 10 ■ Memo pad function The transceiver has a Memo pad function to store the displayed data for easy writing and recalling. The memo pads are separate from the Memory channels. The default number of memo pads is 5. However, you can increase the number to 10 in the "Memopad Numbers" item
  • Icom IC-9100 | Instruction Manual - Page 154
    Scanning automatically searches for signals and makes it easier to locate new stations for contact or listening purposes. The IC-9100 has several scan types; Programmed scan, Memory scan, Select Memory scan, Mode Select scan and ∂F (Delta Frequency) scan. PROGRAMMED SCAN (p. 149) Repeatedly scans
  • Icom IC-9100 | Instruction Manual - Page 155
    Memory scan: Program two or more Memory channels. (Program Scan Edge channels will not be scanned.) (p. 140) For a Mode Select scan: Program two or more Memory channels, all with the same operating mode. (p. 43) For a Select Memory scan: Program two or more Memory channels as Select Memory channels
  • Icom IC-9100 | Instruction Manual - Page 156
    11 SCANS ■ Scan set mode The scan speed, Scan Resume function and [MAIN DIAL] scan function can be set in the Scan Set mode. q P ush [MENU] one or more times to display the "M2" screen (Menu 2). w P ush [SCAN](F-1) to display the "SCAN" screen. e P ush [SET](F-5) to enter the Scan Set mode. r P
  • Icom IC-9100 | Instruction Manual - Page 157
    Scan edges programming Memory channels 1A-3A and 1b-3b are the Program Scan Edge channels. They are used to program the upper and lower frequency edges for programmed scans. (p. 149) Each frequency band has its own Scan Edge channels. Factory default frequency and operating modes are programmed into
  • Icom IC-9100 | Instruction Manual - Page 158
    set to "AUTO," the squelch is always open in the SSB, CW and RTTY modes. (pp. 44, 162) u H old down [PRO](F-1) for 1 second to select the desired scan range between "P1," "P2" and "P3." • The scan searches between programmed scan channels 1A-1b (P1), 2A-2b (P2) or 3A-3b (P3). i Push [PRO
  • Icom IC-9100 | Instruction Manual - Page 159
    always open in the SSB, CW and RTTY modes. (pp. 44, 162) t Push [MEM](F-1) to start the Memory scan. • T he MHz and kHz Repeatedly scans all Memory channels with the same operating mode as the displayed mode. NOTE: For a Mode Select scan to start, two or more Memory channels must be programmed
  • Icom IC-9100 | Instruction Manual - Page 160
    MEM EDT ( 14.19500 USB ) SEL "MEM" screen (Memory Menu) D Select Memory scan Select Memory scan searches for signals through Memory channels specified as "Sel" (Select). NOTE: For a Select Memory scan to start, two or more Memory channels must be designated as Select Memory channels. (See above
  • Icom IC-9100 | Instruction Manual - Page 161
    control function is set to "AUTO," the squelch is always open in the SSB, CW and RTTY modes. (pp. 44, 162) t P ush [SPAN](F-4) one or more times to to set the center frequency. • In the memory mode, rotate [M-CH] to select the desired Memory channel whose frequency will be the center frequency. u
  • Icom IC-9100 | Instruction Manual - Page 162
    can be used with the IC-9100. (p. 71) *AG-1200 has been discontinued, but it can be still be used. 4. When you use a reverse tracking satellite in the SSB mode, use LSB for the uplink frequency and USB for the downlink frequency. • W hen using a normal tracking satellite in SSB mode, use USB for
  • Icom IC-9100 | Instruction Manual - Page 163
    , push [SUB] to enable the SUB band setting mode. In the DR mode, pushing [SATELLITE] cancels it, and then switches the transceiver to the satellite mode. If you want to operate in the DR mode after exiting the satellite mode, you must hold down [DV•DR] for 1 second. ■ Tracking selection q Push
  • Icom IC-9100 | Instruction Manual - Page 164
    SATELLITE OPERATION ■ Satellite memory The IC-9100 has 20 satellite memory channels (CH 00 to 19) to memorize both uplink and downlink frequencies, operating modes and other data. D Satellite memory selection q Push [SATELLITE] to enter the satellite mode. w P ush [VFO/MEMO] to select the satellite
  • Icom IC-9100 | Instruction Manual - Page 165
    frequency (SUB band). After adjusting, push [SUB](3.5 2) again. • W hen a particular station's audio is off frequency, use the RIT function (push [RIT]). !0 To exit the satellite operation, push [SATELLITE]. 4 For your convenience As the transceiver has 20 satellite memory channels, once entered
  • Icom IC-9100 | Instruction Manual - Page 166
    operation When your own signal can be received with a loop test, satellite communication can be performed. q W hen a frequency is shifted by the Doppler effect, push [SUB](3.5 2), then rotate [MAIN DIAL] to retune the uplink frequency. • The downlink
  • Icom IC-9100 | Instruction Manual - Page 167
    [ANT•METER] functions, however, the band memory function is disabled. In this case, you must select an antenna manually. • T he antenna connectors for the 144 MHz, 430 MHz and 1200 MHz* bands are automatically selected. [EXAMPLE]: an optional antenna tuner and HF antenna are connected to [ANT1] and
  • Icom IC-9100 | Instruction Manual - Page 168
    in SSB with a soft voice, the internal tuner may not automatically tune correctly. In such cases, manual tuning is helpful. ➥ Hold down [TUNER] for 1 second to start manual tuning. • A sidetone sounds, " " blinks and the TX/RX indi- cator (MAIN Band) lights red while tuning. • If the
  • Icom IC-9100 | Instruction Manual - Page 169
    ■ Optional external tuner operation • AH-4 HF/50 MHz AUTOMATIC ANTENNA TUNER The optional AH-4 matches the IC-9100 to a long wire antenna more than 7 m/23 ft long (3.5 MHz and above). • See page 29 for the transceiver and AH-4 connec- tion. • See the AH-4 instruction manual installation and an
  • Icom IC-9100 | Instruction Manual - Page 170
    you can hear a beep tone. If you select "ON (User)" or "ON (User) & TX," you can program a total of 30 band edge frequencies in the "User band Edge" item. You can set the beep output level in the "Beep Level" item as described to the left. • OFF : Band edge beep is OFF • ON (Default) : When you
  • Icom IC-9100 | Instruction Manual - Page 171
    User)" or "ON (User) & TX" in the "Band Edge Beep" item, you can program a total of 30 band edge frequencies in this item. See page 42 for programming details. To prevent a prolonged transmission, the transceiver ON, the peak level of a received signal strength or the output power is displayed 16
  • Icom IC-9100 | Instruction Manual - Page 172
    on the selected frequency band and transceiver version. NOTE: • Y ou can use this setting only when the Split func- tion is OFF for the HF/50 MHz frequency band is displayed when a blank memory channel is selected, or the satellite mode is ON. The optional UX-9100 is required for 1200 MHz
  • Icom IC-9100 | Instruction Manual - Page 173
    14 25. SPEECH Level (Default: 50%) Adjust the speech audio output level to between 0% (no output) and 100% (maximum output). 26. SPEECH ∂TX frequency offset. 10 (Default: SPEECH/LOCK) 35. AFC Limit 11 (Default: ON) Select the [SPEECH/LOCK] switch action. Turn the AFC (Automatic
  • Icom IC-9100 | Instruction Manual - Page 174
    the sideband used to receive CW in the CW normal mode between LSB and USB. 43. KEYER 1st Menu (Default: KEYER-Root) Select KEYER-Root or KEYER-SEND as the menu that appears first after pushing [KEY](F-4) in the "M1" screen (Menu 1), when the CW mode is selected. • KEYER-Root : Memory keyer menu
  • Icom IC-9100 | Instruction Manual - Page 175
    HSEND is used for all bands. • UHF Only : VSEND is used for the 430 MHz and 15 MAIN and SUB Band audio are separately sent to the right speaker (MAIN 1200 MHz bands. HSEND is used for the HF/50 MHz and 16 Band) and left speaker (SUB Band). When the SUB Band is not displayed
  • Icom IC-9100 | Instruction Manual - Page 176
    the IC-9100 automatically changes those settings on other Icom transceivers or receivers, and vice versa. • OFF : Transceive function OFF • ON : Transceive function ON 63. USB2/DATA1 Func (Default: [-----]/GPS) Two COM port numbers are assigned to the [USB] connector. One of them is "USB1," used
  • Icom IC-9100 | Instruction Manual - Page 177
    (Default: -----/[GPS ]) Select the function of the [DATA1] jack. • ----- : The [DATA1] jack is not used. • RTTY : U sed to send RTTY decoded signals. • DVdat : U sed for low-speed data input and output. • GPS : U sed for the GPS receiver connection for position data input. 65. GPS Out (Default
  • Icom IC-9100 | Instruction Manual - Page 178
    steps. 2. RX HPF/LPF (Default: OFF) (Mode: SSB/CW/RTTY/AM/FM/DV) First select the operating mode, then set the receive level to between -5 and +5. 5. TX Bass (Mode: SSB/AM/FM/DV) (Default: 0) First select the operating mode, then set the transmit audio bass level to between -5 and +5. 6. TX
  • Icom IC-9100 | Instruction Manual - Page 179
    9. TBW(MID) L (Mode: SSB) (Default: 300) Set the lower cut-off frequency of the transmission passband width for your mid setting to 100, 200, 300 or 500 Hz. 10. TBW(MID) H (Mode: SSB) (Default: 2700) Set the higher cut-off frequency of the transmission passband width for your mid setting to
  • Icom IC-9100 | Instruction Manual - Page 180
    1234 FSKK AF GND SEND* RTTY OUTPUT AUDIO INPUT GND PTT Connect to the serial port, parallel port, speaker jack, microphone jack or line IN/ OUT jack, etc. See the instruction manual of the application for details. *e HF/50 MHz : HSEND u 144/430/1200 MHz : VSEND • When using a TNC 13 9 10 11
  • Icom IC-9100 | Instruction Manual - Page 181
    from the [ACC] socket is used. Also, when the data mode is selected, the fixed set- tings listed below are automatically selected; • Speech compressor : OFF • Transmit bandwidth : MID (Fixed to the default value; 300 Hz to 2700 Hz.) • Tx tone (Bass) : 0 • Tx tone (Treble) : 0 [SSB] [AM/FM
  • Icom IC-9100 | Instruction Manual - Page 182
    though the TX indicator lights continuously: - Increase the TNC output level. 173 INFORMATION! When "RTTY" is selected as the "USB2/DATA1 Func" (63) item option in the Set mode, the USB port sends RTTY decode signal. In this case, you must connect a USB cable* between the transceiver's USB port on
  • Icom IC-9100 | Instruction Manual - Page 183
    unit, or subsequent damage to the transceiver due to user installation problems. The option's or the transceiver's Warranty can be voided in such situations, at the sole judgment of Icom. The following are instructions for removing the covers of the IC-9100. R WARNING! Turn OFF the power and
  • Icom IC-9100 | Instruction Manual - Page 184
    to their original positions. R WARNING! When UX-9100 is installed, the unit continues to draw current, even when the transceiver is turned OFF. Therefore, when you don't intend to use the transceiver for a long period of time, disconnect the transceiver's DC power cable. Secure the coaxial cable
  • Icom IC-9100 | Instruction Manual - Page 185
    . • T he connectors on the IC-9100 are marked for the appropriate filter. • Ensure the FL-430 or FL-431 is installed correctly. e R eturn the top and bottom covers to the original positions. After installation, a 6 kHz or 3 kHz filter width can be used
  • Icom IC-9100 | Instruction Manual - Page 186
    ■ Troubleshooting The following chart is designed to help you correct problems which are not equipment malfunctions. If you are unable to locate the cause of a problem, or solve it through the use of this chart, contact your nearest Icom Dealer or Service Center. D Transceiver power PROBLEM
  • Icom IC-9100 | Instruction Manual - Page 187
    mode • Program more than 2 memory channels with p. 43 does not start. have not been programmed. the desired operating mode. ∂F scan does not start. • T he center frequency for ∂F scan is not pro- • Program the center frequency for a ∂F scan. p. 152 grammed. D Display PROBLEM POSSIBLE CAUSE
  • Icom IC-9100 | Instruction Manual - Page 188
    transceiver. However, a rough check may be performed by receiving radio station WWV, WWVH, or other standard frequency signals. CAUTION: The IC-9100 has been thoroughly adjusted and tested at the factory before being shipped. You should not have to re-calibrate it. q P ush [SSB] to select the USB
  • Icom IC-9100 | Instruction Manual - Page 189
    transceiver stops functioning, find the source of the problem, and repair it. Then replace the damaged fuse with a new, adequately rated fuse. The IC-9100 has two fuse types installed for transceiver plate as shown to the right. e R emove the speaker cable from the connector on the PA unit as shown
  • Icom IC-9100 | Instruction Manual - Page 190
    contents • Call sign memories • Repeater lists • TX messages • GPS memories • GPS messages • Memory keyer contents • Programmed user band edge frequencies • Programmed Auto Repeater frequency ranges • REF Adj (Reference frequency) setting q First, turn OFF the transceiver power. w W hile holding
  • Icom IC-9100 | Instruction Manual - Page 191
    MAINTENANCE 17 ■ Data cloning DCloning between transceivers The IC-9100 has transceiver-to-transceiver data cloning capability. This function is useful when you want to copy all of the programmed contents from one IC-9100 to another. • A mini plug cable is required. (Purchase separately) q C
  • Icom IC-9100 | Instruction Manual - Page 192
    (CI-V) controls the transceiver. Up to 4 Icom CI-V transceivers or receivers can be connected to the PC. See page 167 for setting the CI-V condition using the set mode. 9−15V DC RS-232C cable PC ct-17 IC-9100 mini-plug cable When the transceiver is connected to a PC with the USB cable (purchased
  • Icom IC-9100 | Instruction Manual - Page 193
    =3b) 0106 Select Call channel 00 to 19 Select Satellite Memory channel (00=Satellite M-CH00 to 19=Satellite M-CH19) Memory write Memory copy to VFO Memory clear Read offset frequency Send offset frequency 00 Scan stop 01 Programmed/memory scan start 02 Programmed scan start 03 ∂F scan
  • Icom IC-9100 | Instruction Manual - Page 194
    /read CSQL ON (DV mode only) see p. 191 Send CW messages 00 Read the transceiver ID 00 see p. 195 Send/read memory contents 01 see p. 191 Send/read band stacking register contents 02 see p. 191 Send/read memory keyer contents*1 03 00 to 49 Send/read the selected filter width (AM: 00=200 Hz
  • Icom IC-9100 | Instruction Manual - Page 195
    [DATA] AF/SQL line output Send/read SUB selection for the [DATA] AF/SQL line output Send/read VSEND select OFF Send/read UHF Only selection for VSEND Send/read VSEND select ON Send/read external keypad OFF Send/read KEYER SEND selection for the external keypad Send/read USB audio squelch OFF (OPEN
  • Icom IC-9100 | Instruction Manual - Page 196
    during DATA mode ON 03 Send/read USB selection for the modulation input during DATA mode ON 0058 00 Send/read CI-V transceive OFF 01 Send/read CI-V transceive ON 0059 00 Send/read no function selection for "USB2" (COM port) function 01 Send/read RTTY selection for "USB2" (COM port) function
  • Icom IC-9100 | Instruction Manual - Page 197
    keying polarity 00 Send/read RTTY decode USOS OFF 01 Send/read RTTY decode USOS ON 00 Send/read "CR,LF,CR+LF" selection for RTTY decode new line code 01 Send/read "CR+LF" selection for RTTY decode new line code 00 Send/read 2 lines selection for number of RTTY decoder line 01 Send/read 3 lines
  • Icom IC-9100 | Instruction Manual - Page 198
    Satellite memory contents 00 see p. 193 Send/read Repeater tone frequency 01 see p. 193 Send/read Tone squelch frequency 02 see p. 193 Send/read DTCS code and polarity 07 see p. 193 Send/read CSQL code (DV mode) 00 00 Send/read Transceiver's status (RX) 01 Send/read Transceiver's status (TX
  • Icom IC-9100 | Instruction Manual - Page 199
    *1 The counter can be inserted into only one channel. *2 Output setting is automatically turned OFF after turning the power OFF, then ON USB 04: RTTY 08: RTTY-R 02: FIL2 02: AM 05: FM 17: DV 03: FIL3 Filter setting (w) can be skipped with command 01 and 06. In that case, "FIL1" is automatically
  • Icom IC-9100 | Instruction Manual - Page 200
    (latest) 02 2 03 3 (oldest) For example, when reading the oldest contents in the 21 MHz band, the code "0703" is used. • Memory keyer contents Command : 1A 02 X X X X ...... X X w-&1: Text data q: Channel data 01ɿM1 03ɿM3 02ɿM2 04ɿM4 • Character's code Character ASCII code Description
  • Icom IC-9100 | Instruction Manual - Page 201
    0-9 *10 MHz digit can be entered on only the 1200 MHz frequency band. • SSB transmission bandwidth setting Command : 1A 05 0072, 0073, digit: 0-9 0.01 min. digit: 0-9 0.001 min. digit: 0-9 0 (fixed) 0 (fixed) S*=0/N*=1 0 (fixed) 100 degree digit: 0-1 10 degree digit: 0-9 1 degree digit: 0-9 10
  • Icom IC-9100 | Instruction Manual - Page 202
    9999 e  • Repeater tone/tone squelch frequency setting Command : 1B 00, 1B 01 q* w e 0 0 X X X X 0 (fixed) 0 (fixed) 100 Hz digit 10 XX Second digit First digit ⁄, \, 0 to 9, A to Z can be used for the first digit character. See 'Character code setting' for the second digit character
  • Icom IC-9100 | Instruction Manual - Page 203
    ) @3-#0 Call sign of the access/area repeater (R1) (8 characters; fixed) #1-#8 Call sign of the link/gateway repeater (R2) (8 characters; fixed) See 'Character code setting.' (p. 190) "FF" stands for no call sign receiving after turning ON the transceiver. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
  • Icom IC-9100 | Instruction Manual - Page 204
    q Frequency band setting 00 : HF/50 MHz frequency band 01 : 144 MHz frequency band 02 : 430 MHz frequency band 03 : 1200 MHz frequency band w, e Memory channel number 0001-0099 : Memory channel 1 to 99 0100 : Programmed scan edge 1A 0101 : Programmed scan edge 1b 0102 : Programmed scan edge
  • Icom IC-9100 | Instruction Manual - Page 205
    characters; fixed) #9-$6 R2 (Link/Gateway repeater) call sign setting (8 characters; fixed) See '• DV TX call signs setting.' (p. 194) $7-%5 Memory name setting 9 characters (Fixed) See '• Character code setting.' (p. 190) NOTE: • The same data as e-$6 are stored in e-$6. • e-$6 is used for the
  • Icom IC-9100 | Instruction Manual - Page 206
    channels : 18CH (6 × 3 band) (24CH with UX-9100‡; 6CH × 4 bands) • N o. of call channels : 3CH (1 × 3 band) (4CH with UX-9100‡; 1CH × 4 bands) • N o. of Satellite memory channels : 20CH • Antenna connector : SO-239 × 3 Type-N × 2 • Antenna impedance : 50 ø (at Antenna Tuner
  • Icom IC-9100 | Instruction Manual - Page 207
    (BW: 500 Hz) : More than 500 Hz/-6 dB Less than 700 Hz/-40 dB RTTY (BW: 500 Hz) : More than 500 Hz/-6 dB Less than 800 Hz/-40 dB AM HF/50 MHz band* : More than 70 dB *except IF through on 50 MHz band 144/430 MHz band : More than 60 dB 1200 MHz band† : More than 50 dB • AF output
  • Icom IC-9100 | Instruction Manual - Page 208
    20 OPTIONS IC-PW1/EURO HF/50 MHz ALL BAND 1 kW LINEAR AMPLIFIER AH-4 hf automatic antenna tuner Full-duty 1 kW linear amplifier including an automatic antenna tuner. Has automatic tuning and band selection capability. Full break-in (QSK) operation is possible. The amplifier/power supply unit and
  • Icom IC-9100 | Instruction Manual - Page 209
    The same as that attached with the transceiver. • UT-121 digital unit Allows the DV mode operation with the IC-9100. • CS-9100 cloning software Use this software to program settings, memory channels and set mode contents quickly and easily via your PC's USB port. A USB cable is required. (A-B type
  • Icom IC-9100 | Instruction Manual - Page 210
    of time. Some radio licenses will require that a timer circuit automatically cuts off the transmitter after 1-2 minutes etc. Similarly some modes of transmission, SSB, CW, AM etc. have a lower 'average' output power and the assessed risk is even lower. Versions of the IC-9100 which display the
  • Icom IC-9100 | Instruction Manual - Page 211
    , and that any applicable Essential Test Suite measurements have been performed. Kind of equipment: HF/VHF/UHF TRANSCEIVER Type-designation: iC- 9100 Version (where applicable): This compliance is based on conformity with the following harmonised standards, specifications or documents: i) EN 301 489
  • Icom IC-9100 | Instruction Manual - Page 212
    NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR HR IC-9100 #04 (Europe-1) < Intended Country of Use > AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT of Use > AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT LU MT NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR HR A-6871H-1EX Printed in Japan © 2011 Icom Inc
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
HF/VHF/UHF TRANSCEIVER
i9100
INSTRUCTION MANUAL