Icom ID-52A Ci-v Reference Guide english - Page 6

REMOTE CONTROL Remote control (CI-V) information DDCommand table Command Sub 16* 42 43 46 4B 59 5B 5C 5D 18 00 01*2 19 00 1B* 00 01 02 07 1C* 00 1F* 00 01 02 20 00 00* 01 02 01 00* 01 02 02 00* 01 02 Data 00/01 00 ~ 02 00/01 00 ~ 02 00 01 00 ~ 02 00 ~ 02 00 ~ 09 See p. 7 See p. 7 See p. 7 See p. 7 00/01 See p. 7 See p. 7 See p. 8 00/01*3 See p. 8 See p. 8 00/01*3 See p. 9 See p. 9 00/01*3 See p. 9 See p. 9 Description Send/read the Repeater tone (00=OFF, 01=ON) Send/read the Tone squelch (00=OFF, 01=TSQL, 02=TSQL-R) Send/read the VOX function (00=OFF, 01=ON) Send/read the DTCS function (00=OFF, 01=DTCS, 02=DTCS-R) Send/read SUB band OFF Send/read SUB band ON Send/read the DSQL (Digital Call Sign squelch)/CSQL (Digital Code squelch) setting (DV mode only) (00=OFF, 01=DSQL, 02=CSQL) Send/read the GPS TX mode (00=OFF, 01=D-PRS, 02=NMEA) Send/read the Tone squelch function (00=OFF, 01=TONE, 02=TSQL, 03=DTCS, 04=TSQL-R, 05=DTCS-R, 06=DTCS (T), 07=TONE (T)/DTCS (R), 08=DTCS (T)/TSQL (R), 09=TONE (T)/TSQL (R)) Turn OFF the transceiver Turn ON the transceiver Read the transceiver ID Send/read the Repeater tone frequency Send/read the TSQL tone frequency Send/read the DTCS code and polarity Send/read the CSQL code (DV mode) Send/read the transceiver's status (00=RX, 01=TX) Send/read the My Call Sign setting Send/read the DV TX Callsign setting Send/read the DV TX Message setting Send/read the Auto DV RX Call signs output (00=OFF, 01=ON) Output DV RX Call signs for transceive Read Auto DV RX Call signs Send/read the Auto DV RX message output (00=OFF, 01=ON) Output DV RX message for transceive Read Auto DV RX message Send/read the Auto DV RX status output (00=OFF, 01=ON) Output DV RX status for transceive Read Auto DV RX status Command Sub 20 03 00* 01 02 04 00* 01 02 22 00 01 00 01 02* 03* 04* 05* 23 00 01* 02* 24 00 00* 01 Data 00/01 See p. 9 and 11 See p. 9 and 11 00/01 See p. 12 See p. 12 See p. 12 00/01 See p. 12 00/01 00/01 00/01 00 ~ 10 See p. 12 00/01/03 See p. 12 00/01 00/01 Description Send/read the Auto DV RX GPS/D-PRS data output (00=OFF, 01=ON) Output DV RX GPS/D-PRS data for transceive Read DV RX GPS/D-PRS data for transceive Send/read Auto DV RX GPS/D-PRS message output (00=OFF, 01=ON) Output DV RX D-PRS message for transceive Read Auto DV RX D-PRS message status Set the DV TX data (Up to 30 byte) Set the Auto DV RX data output (00=OFF, 01=ON) Set the DV RX data for transceive (Up to 30 byte) Send/read DV data TX setting (00=PTT, 01=Auto) Send/read DV fast data setting (00=OFF, 01=ON) Send/read GPS Data Speed setting (00=Slow, 01=Fast) Send/read TX Delay (PTT) setting (00=OFF, 01=1 sec. ~ 10=10 sec.) Read the position status Send/read the internal GPS OFF (00=OFF, 01=Internal GPS, 03=Manual) Send/read the manually input position data Send/read TX output power setting (00=OFF, 01=ON) Set the TX output power for transceive (00=OFF, 01=ON) *(Asterisk) Send/read data *1 Less than 100 Hz is omitted. *2 When sending the power ON command (18 01) using the [SP] jack (p. 3), the command "FE" must be sent before the basic format. The following is the approximate number of needed repetitions. •4800bps: 15 "FE"s •9600bps: 30 "FE"s •19200bps: 60 "FE"s Example: When operating with 4800 bps q w e r t u FE F E F E A 6 E 0 1 8 0 1 F D ×15 1 Preamble code (fixed) 2 Transceiver's default address 3 Controller's default address 4 Command number 5 Sub command number 7 End of message code (fixed) *3 Output setting is automatically set to OFF after turning OFF the transceiver. 5