Intel DH55TC DH55TC Technical Product Specification - Page 44

Add-in Card Connectors, 2.2.3, Power Supply Connectors, CAUTION

Get Intel DH55TC PDF manuals and user guides View all Intel DH55TC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Intel Desktop Board DH55TC Technical Product Specification 2.2.2.2 Add-in Card Connectors The board has the following add-in card connectors: • One PCI Express 2.0 x16: this connector supports simultaneous transfer speeds of up to 8 GB/s of peak bandwidth per direction. • Two PCI Express 2.0 x1: each of these connectors support simultaneous transfer speeds of up to 500 MB/s of peak bandwidth per direction. • One Conventional PCI (rev 2.3 compliant) connector. Note the following considerations for the Conventional PCI bus connector: • The Conventional PCI bus connector is bus master capable. • SMBus signals are routed to the Conventional PCI bus connector. This enables Conventional PCI bus add-in boards with SMBus support to access sensor data on the desktop board. The specific SMBus signals are as follows: ⎯ The SMBus clock line is connected to pin A40. ⎯ The SMBus data line is connected to pin A41. 2.2.2.3 Power Supply Connectors The board has the following power supply connectors: • Main power - a 2 x 12 connector. This connector is compatible with 2 x 10 connectors previously used on Intel Desktop boards. The board supports the use of ATX12V power supplies with either 2 x 10 or 2 x 12 main power cables. When using a power supply with a 2 x 10 main power cable, pins 11, 12, 23, and 24 must remain unconnected. • Processor core power - a 2 x 2 connector. This connector provides power directly to the processor voltage regulator and must always be used. Failure to do so will prevent the board from booting. CAUTION If a high power (75 W or greater) add-in card is installed in the PCI Express x16 connector, that card must also be connected directly to the power supply. Failure to do so may cause damage to the board and the add-in card. Table 21. Processor Core Power Connector Pin Signal Name Pin Signal Name 1 Ground 3 +12 V 2 Ground 4 +12 V 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Intel Desktop Board DH55TC Technical Product Specification
44
2.2.2.2
Add-in Card Connectors
The board has the following add-in card connectors:
•
One PCI Express 2.0 x16:
this connector supports simultaneous transfer speeds of
up to 8 GB/s of peak bandwidth per direction.
•
Two PCI Express 2.0 x1:
each of these connectors support simultaneous transfer
speeds of up to 500 MB/s of peak bandwidth per direction.
•
One Conventional PCI (rev 2.3 compliant) connector.
Note the following considerations for the Conventional PCI bus connector:
•
The Conventional PCI bus connector is bus master capable.
•
SMBus signals are routed to the Conventional PCI bus connector.
This enables
Conventional PCI bus add-in boards with SMBus support to access sensor data on
the desktop board.
The specific SMBus signals are as follows:
⎯
The SMBus clock line is connected to pin A40.
⎯
The SMBus data line is connected to pin A41.
2.2.2.3
Power Supply Connectors
The board has the following power supply connectors:
•
Main power
– a 2 x 12 connector.
This connector is compatible with 2 x 10
connectors previously used on Intel Desktop boards.
The board supports the use
of ATX12V power supplies with either 2 x 10 or 2 x 12 main power cables.
When
using a power supply with a 2 x 10 main power cable, pins 11, 12, 23, and
24 must remain unconnected.
•
Processor core power
– a 2 x 2 connector.
This connector provides power
directly to the processor voltage regulator and must always be used.
Failure to do
so will prevent the board from booting.
CAUTION
If a high power (75 W or greater) add-in card is installed in the PCI Express x16
connector, that card must also be connected directly to the power supply.
Failure to
do so may cause damage to the board and the add-in card.
Table 21.
Processor Core Power Connector
Pin
Signal Name
Pin
Signal Name
1
Ground
2
Ground
3
+12 V
4
+12 V