Intel DX79SI Product Guide for Intel Desktop Board DX79SI - Page 64

Installing the WiFi/Bluetooth* Module in Your Chassis,

Get Intel DX79SI PDF manuals and user guides View all Intel DX79SI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Intel Desktop Board DX79SI Product Guide Installing the WiFi/Bluetooth* Module in Your Chassis Installing the WiFi/Bluetooth module that is shipped with Intel Desktop Board DX79SI in your desktop system allows you to connect to wireless networks and Bluetooth peripherals. The recommended installation procedure for a typical desktop chassis is as follows: 1. Observe the precautions in "Before You Begin" on page 33. 2. Make sure that the system is turned off and disconnected from its power source. 3. Remove the plastic cover from an empty 5-1/4 inch drive bay in the chassis bezel (Figure 28, A). 4. Remove the metal filler plate from the internal drive bay (Figure 28, B). 5. Remove the paper backing covering the adhesive on the back of the WiFi/Bluetooth Module and attach the module to the back side of the plastic drive bay cover (Figure 28, C). 6. Connect one end of the USB cable to the connector on the front of the module (Figure 28, D). 7. Reinstall the plastic drive bay cover in the chassis bezel while routing the USB cable into the chassis through the empty drive bay (Figure 28, E). 8. Connect the free end of the USB cable to an unused front panel USB header on the Desktop Board (see Figure 22, G for locations) (Figure 28, F). Figure 28. Installing the WiFi/Bluetooth Module 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Intel Desktop Board DX79SI Product Guide
64
Installing the WiFi/Bluetooth* Module in
Your Chassis
Installing the WiFi/Bluetooth module that is shipped with Intel Desktop Board DX79SI
in your desktop system allows you to connect to wireless networks and Bluetooth
peripherals.
The recommended installation procedure for a typical desktop chassis is as follows:
1.
Observe the precautions in "Before You Begin" on page 33.
2.
Make sure that the system is turned off and disconnected from its power source.
3.
Remove the plastic cover from an empty 5-1/4 inch drive bay in the chassis bezel
(Figure 28, A).
4.
Remove the metal filler plate from the internal drive bay (Figure 28, B).
5.
Remove the paper backing covering the adhesive on the back of the WiFi/Bluetooth
Module and attach the module to the back side of the plastic drive bay cover
(Figure 28, C).
6.
Connect one end of the USB cable to the connector on the front of the module
(Figure 28, D).
7.
Reinstall the plastic drive bay cover in the chassis bezel while routing the USB
cable into the chassis through the empty drive bay (Figure 28, E).
8.
Connect the free end of the USB cable to an unused front panel USB header on the
Desktop Board (see Figure 22, G for locations) (Figure 28, F).
Figure 28.
Installing the WiFi/Bluetooth Module