Jenn-Air JDS9860CDS Use and Care - Page 7

Sealed Surface Burners, Sealed Burner Cartridge

Get Jenn-Air JDS9860CDS PDF manuals and user guides View all Jenn-Air JDS9860CDS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Sealed Surface Burners A 2. Clean the gas tube opening with a damp cloth. 3. Clean clogged burner ports with a straight pin as shown. Do not enlarge or distort the port. Do not use a wooden toothpick. If the burner needs to be adjusted, contact a trained repair specialist. B D E C A. Burner cap B. Burner base C. Alignment pins D. Igniter E. Gas tube opening IMPORTANT: Do not obstruct the flow of combustion and ventilation air around the burner grate edges. Burner cap: Always keep the burner cap in place when using a surface burner. A clean burner cap will help avoid poor ignition and uneven flames. Always clean the burner cap after a spillover and routinely remove and clean the caps according to the "General Cleaning" section. Gas tube opening: Gas must flow freely throughout the gas tube opening for the burner to light properly. Keep this area free of soil and do not allow spills, food, cleaning agents or any other material to enter the gas tube opening. Keep spillovers out of the gas tube by always using a burner cap. A B A. 1-1¹⁄₂" (25-38 mm) B. Burner ports Burner ports: Check burner flames occasionally for proper size and shape as shown in the previous illustration. A good flame is blue in color, not yellow. Keep this area free of soil and do not allow spills, food, cleaning agents or any other material to enter the burner ports. To Clean: IMPORTANT: Before cleaning, make sure all controls are off and the oven and cooktop are cool. Do not use oven cleaners, bleach or rust removers. 1. Remove the burner cap from the burner base and clean according to "General Cleaning" section. 4. Replace the burner cap, making sure the alignment pins are properly aligned with the burner cap. A B A. Incorrect B. Correct 5. Turn on the burner. If the burner does not light, check cap alignment. If the burner still does not light, do not service the sealed burner yourself. Contact a trained repair specialist. Sealed Burner Cartridge The Sealed Burner Cartridge can only be installed on the left side of the cooktop. To Install Sealed Burner Cartridge: 1. Be sure control knobs are in the "Off" position. 2. If grill burner and grill grates are in place, remove before installing a burner cartridge. Clean basin of any grease accumulation, see "General Cleaning" section. 3. The orifices and terminal receptacle are located in the basin at the front of the cooktop. A B B A. Terminal receptacle B. Orifices 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
7
Sealed Surface Burners
IMPORTANT:
Do not obstruct the flow of combustion and
ventilation air around the burner grate edges.
Burner cap:
Always keep the burner cap in place when using a
surface burner. A clean burner cap will help avoid poor ignition
and uneven flames. Always clean the burner cap after a spillover
and routinely remove and clean the caps according to the
“General Cleaning” section.
Gas tube opening:
Gas must flow freely throughout the gas tube
opening for the burner to light properly. Keep this area free of soil
and do not allow spills, food, cleaning agents or any other
material to enter the gas tube opening. Keep spillovers out of the
gas tube by always using a burner cap.
Burner ports:
Check burner flames occasionally for proper size
and shape as shown in the previous illustration. A good flame is
blue in color, not yellow. Keep this area free of soil and do not
allow spills, food, cleaning agents or any other material to enter
the burner ports.
To Clean:
IMPORTANT:
Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Do not use oven cleaners, bleach
or rust removers.
1.
Remove the burner cap from the burner base and clean
according to “General Cleaning” section.
2.
Clean the gas tube opening with a damp cloth.
3.
Clean clogged burner ports with a straight pin as shown. Do
not enlarge or distort the port. Do not use a wooden
toothpick. If the burner needs to be adjusted, contact a
trained repair specialist.
4.
Replace the burner cap, making sure the alignment pins are
properly aligned with the burner cap.
5.
Turn on the burner. If the burner does not light, check cap
alignment. If the burner still does not light, do not service the
sealed burner yourself. Contact a trained repair specialist.
Sealed Burner Cartridge
The Sealed Burner Cartridge can only be installed on the left side
of the cooktop.
To Install Sealed Burner Cartridge:
1.
Be sure control knobs are in the “Off” position.
2.
If grill burner and grill grates are in place, remove before
installing a burner cartridge. Clean basin of any grease
accumulation, see “General Cleaning” section.
3.
The orifices and terminal receptacle are located in the basin
at the front of the cooktop.
A. Burner cap
B. Burner base
C. Alignment pins
D. Igniter
E. Gas tube opening
A. 1-1
¹⁄₂
" (25-38 mm)
B. Burner ports
A
B
D
E
C
B
A
A. Incorrect
B. Correct
A. Terminal receptacle
B. Orifices
A
B
A
B
B