Kenmore 4101 Installation Instructions - Page 11

Leveling, Range, required, Check, Operation

Get Kenmore 4101 - Elite 30 in. Slide-In Electric Range PDF manuals and user guides View all Kenmore 4101 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Leveling the Range - Level the range after installation in the cutout opening. 1. Open the range drawer. The leveling screws control the height of the rear leg. 2. Adjust the appliance legs as follows until the underside of the cooktop surface is sitting level on the countertop (Figure 12). Decorative Rear Trim Installation (if required) 1. Disconnect the power from the range. 2. Make sure the range is leveled. 3. Pull range toward you. 4. Measure the distance between the floor and the surface underneath the cooktop frame. , Mark that distance on the wall where the decorative trim will be installed. , Draw a line. 7. Place the top of the decorative trim under that line. 8. Using the screws provided fix the decorative trim into the wall. , Slide the range back into position as far as it will go and reconnect the power source. Decorative Trim Font LevLeeligng _ LOWER RAISE Fig u re 12 1. To adjust the front leveling legs, use a wrench and turn counterclockwise to lower or clockwise to raise. 2. To adjust the rear leveling screws, use a ratchet or a nutdriver and turn counterclockwise to lower or clockwise to raise. 3. Check if the range is level by installing an oven rack in the center of the oven and placing a level on the rack (Figure 13) 4. Take 2 readings with the level placed diagonally in one direction and then theother.Levelthe range, if necessary, by adjusting the leveling legs. 5. If the range is not level, contact a carpenter to correct sagging or sloping floor. Figure 13 Distance underneath the --._:ooktop frame. \'\-\. Figure 14 Check Operation Refer to the Use and Care Guide packaged with the range for operating instructions and for care and cleaning of your range. Do not touch the elements or burners. They may be hot enough to cause burns. Remove all packaging from the oven before testing. 1.Install Burner Bases and Burner Caps This range is equipped with sealed burners as shown (see Figure 15 on next page). 1. Unpack burner bases and burner caps. 2. Place burner bases over each gas opening. 3. Make sure the burner is properly aligned and leveled. Placeburner caps over appropriate burner bases. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
Leveling
the
Range
-
Level the range after installation
in the cutout opening.
1. Open the range drawer. The leveling screws control
the height of the rear leg.
2. Adjust the appliance legs as follows until the underside
of the cooktop surface is sitting level on the countertop
(Figure 12).
(if
1.
2.
3.
4.
,
,
7.
8.
,
Decorative
Rear
Trim
Installation
required)
Disconnect the power from the range.
Make sure the range is leveled.
Pull range toward
you.
Measure the distance between
the floor
and the
surface underneath
the cooktop frame.
Mark that distance on the wall where the decorative
trim will
be installed.
Draw a line.
Place the top of the decorative trim under that
line.
Using the screws provided fix the decorative trim into
the wall.
Slide the range back into position
as far as it will go
and reconnect the power source.
Decorative
Trim
Font
Leveling
_
Fig u re 12
Leg
LOWER
RAISE
1. To adjust the front leveling legs, use a wrench and turn
counterclockwise to lower or clockwise to raise.
2. To adjust the rear leveling screws, use a ratchet or a
nutdriver and turn counterclockwise to lower or
clockwise to raise.
3.
Check if the range is level by installing an oven rack in
the center of the oven and placing a level on the rack
(Figure 13)
4.
Take 2 readings with the level placed diagonally in
one direction and then theother.Levelthe
range, if
necessary, by adjusting the leveling legs.
5.
If the range is not level, contact a carpenter to correct
sagging or sloping floor.
Figure
13
Distance
underneath
the
--._:ooktop
frame.
\'\-\.
Figure
14
Check
Operation
Refer to the Use and
Care
Guide packaged with
the
range for operating
instructions
and for care and cleaning
of your range.
Do not touch the elements or burners. They may be hot
enough to cause burns.
Remove all packaging
from the oven before testing.
1.Install
Burner
Bases and Burner
Caps
This range
is equipped
with
sealed
burners
as
shown
(see Figure
15 on next
page).
1. Unpack burner bases and burner caps.
2. Place burner bases over each gas opening.
3. Make sure the burner is properly aligned and leveled.
Placeburner caps over appropriate burner bases.
11