Kenwood DDX419 Instruction Manual - Page 77

DDX719/ DDX7049BT only, DDX419/ DDX4049BT only, CAUTION

Get Kenwood DDX419 PDF manuals and user guides View all Kenwood DDX419 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

• Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the wires or ground them to any metal part in the car. • When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Mount the unit so that the mounting angle is 30° or less. • Do not press hard on the panel surface when installing the unit to the vehicle. Otherwise scars, damage, or failure may result. • This unit has the cooling fan to decrease the internal temperature. Do not mount the unit in a place where the cooling fan of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction. DDX719/ DDX7049BT only 1 Before installation, remove the screws. ⁄ Do not use the removed screws for installation. 2 Detach the sleeve using the two removal tools 7 then slide off the sleeve. Accessory 7 Cooling fan DDX419/ DDX4049BT only • Install the Bluetooth adaptor (KS-UBT1) besides the place enclosed by the metal. ¤ CAUTION Install this unit in the console of your vehicle. Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot. . Bluetooth adaptor (KS-UBT1) English 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
English
77
•
Insulate unconnected wires with vinyl tape or
other similar material. To prevent a short circuit,
do not remove the caps on the ends of the
unconnected wires or the terminals.
•
Connect the speaker wires correctly to the
terminals to which they correspond. The unit may
be damaged or fail to work if you share the
-
wires or ground them to any metal part in the car.
•
When only two speakers are being connected
to the system, connect the connectors either to
both the front output terminals or to both the
rear output terminals (do not mix front and rear).
For example, if you connect the
+
connector
of the left speaker to a front output terminal, do
not connect the
-
connector to a rear output
terminal.
•
After the unit is installed, check whether the
brake lamps, blinkers, wipers, etc. on the car are
working properly.
•
Mount the unit so that the mounting angle is 30°
or less.
•
Do not press hard on the panel surface when
installing the unit to the vehicle. Otherwise scars,
damage, or failure may result.
•
This unit has the cooling fan to decrease the
internal temperature. Do not mount the unit
in a place where the cooling fan of the unit are
blocked. Blocking these openings will inhibit the
cooling of the internal temperature and result in
malfunction.
Cooling fan
DDX719/ DDX7049BT only
1
Before installation, remove the screws.
⁄
Do not use the removed screws for
installation.
2
Detach the sleeve using the two removal
tools
7
then slide off the sleeve.
A
ccessory
7
DDX419/ DDX4049BT only
•
Install the Bluetooth adaptor (KS-UBT1) besides
the place enclosed by the metal.
Bluetooth adaptor (KS-UBT1)
.
¤
CAUTION
Install this unit in the console of your
vehicle.
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.