Kenwood TS-890S Operation Manual

Kenwood TS-890S Manual

Get Kenwood TS-890S PDF manuals and user guides View all Kenwood TS-890S manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood TS-890S manual content summary:

  • Kenwood TS-890S | Operation Manual - Page 1
    . .. TS-890S INSTRUCTION MANUAL B5A-2215-10 (K, E)
  • Kenwood TS-890S | Operation Manual - Page 2
  • Kenwood TS-890S | Operation Manual - Page 3
    USING Thank You Thank you for choosing this KENWOOD TS-890S transceiver. FEATURES ● A high-end and practical transceiver with superior reception performance that exceeds its class, with multiple functions and with a feel of TS-990S ● Incorporates a 7" TFT color display for comfortable centralized
  • Kenwood TS-890S | Operation Manual - Page 4
    , damages or losses arising from, or in connection with, use of the transceiver with or connected to any external equipment. ● JVC KENWOOD Corporation does not warrant that the quality and functions described in this manual comply with your purpose of use and, unless specifically described in this
  • Kenwood TS-890S | Operation Manual - Page 5
    . ● The presence of an unusual odor or smoke is often a sign of trouble. Immediately turn the power OFF and remove the power cable. Contact a KENWOOD service station or your dealer for advice. ● Locate the transceiver away from heat sources such as a radiator, stove, amplifier or other devices that
  • Kenwood TS-890S | Operation Manual - Page 6
    energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there . Firmware Copyrights The title to and ownership of copyrights for firmware embedded in KENWOOD product memories are reserved for JVC KENWOOD Corporation
  • Kenwood TS-890S | Operation Manual - Page 7
    and Connection 1-1 Ground Connection 1-1 Installation of Lightning Arrestors 1-1 Connection of Regulated DC Power Supply 1-1 Using the Auxiliary Support 1-1 Torque Adjustment with Tuning Control 1-2 Connection of Accessories (Front Panel 1-2 Connection of Accessories (Rear Panel 1-3 PC
  • Kenwood TS-890S | Operation Manual - Page 8
    Mode of the Electronic Keyer 5-13 Reversing Dot and Dash 5-13 Mic Paddle Mode 5-13 Adjusting the Keying Speed 5-13 Changing the Weighting 5-14 Weight Ratio Reverse 5-14 CW Message Memory 5-14 Switching the Method of Registering CW Messages 5-14 Registering CW Messages via Text Input 5-14
  • Kenwood TS-890S | Operation Manual - Page 9
    CONTENTS Selecting a Tone 5-29 Configuring the Tone Frequency 5-29 Tone Frequency Scan 5-29 CTCSS Operation 5-30 Selecting CTCSS 5-30 Configuring the CTCSS Frequency 5-30 CTCSS Frequency Scan 5-30 Cross Tone 5-30 Selecting Cross Tone 5-30 Configuring the TX/RX Tones 5-30 6 REJECTING
  • Kenwood TS-890S | Operation Manual - Page 10
    for Repeated Transmission 12-3 Recording/Playing Voice Communication 12-3 Manual Recording 12-3 Full-time Recording 12-4 Configuring the Maximum ON/OFF Auto Clock Correction 14-3 Correcting the Date and Time Manually 14-3 Timer 14-4 Configuring the Program Timer 14-4 Pausing Program
  • Kenwood TS-890S | Operation Manual - Page 11
    DC Power Cable 17-4 18 TROUBLESHOOTING General Information 18-1 Service 18-1 Service Note 18-1 Cleaning 18-1 Troubleshooting 18-2 Problems Related to Reception and Transmission 18-2 Problems Related to Data Communication, PC and Network ....... 18-5 Troubles Related to Recording and Playback
  • Kenwood TS-890S | Operation Manual - Page 12
    . x
  • Kenwood TS-890S | Operation Manual - Page 13
    Next, connect the DC power cord to the DC 13.8 V power connector of this transceiver. Insert the cord fully into the power connector. Using the Auxiliary Support An auxiliary support is stored inside the front leg of this transceiver. Pull it toward you if you want the panel to face slightly upwards
  • Kenwood TS-890S | Operation Manual - Page 14
    Tuning Control The Tuning control allows the rotational torque (weight) to be adjusted according to the user's preference. With speakers (or optional external speakers). The following optional headphones are compatible with this transceiver. ●HS-5 ●HS-6 ● The volume may be louder for headphones with
  • Kenwood TS-890S | Operation Manual - Page 15
    to be shown on the external display. ● Use an external display with a resolution of 800 x 600 or 848 x 480. ● This transceiver supports digital and analog outputs. ● If the display to connect uses a D-sub terminal, make use of a commercially available DVI/D-Sub conversion adapter. ■ External
  • Kenwood TS-890S | Operation Manual - Page 16
    RTTY keying by connecting to a PC (or other external devices) while this transceiver is configured to the FSK mode, please refer to "Operating RTTY (FSK) Using an External Device" (5-22). . RS-232C Straight Cable TS-890S (Female) To RS-232C Serial Port To Audio Input/Output Port To USB
  • Kenwood TS-890S | Operation Manual - Page 17
    this transceiver far enough from the PC so that noise will not be picked up. ● For data communication software settings, refer to the instruction manual . http://www.kenwood.com/i/products/info/amateur/software_download.html • There are 2 types of virtual COM port on this transceiver, namely virtual
  • Kenwood TS-890S | Operation Manual - Page 18
    No. 1 2 3 4 5 6 7 8 9 Pin Name NC RXD TXD NC GND NC RTS CTS NC Function No connection Sends serial data from this transceiver to RXD on the PC. Receives serial data from TXD on the PC to this transceiver. No connection Signal ground No connection Sends signal from RTS on the PC to this
  • Kenwood TS-890S | Operation Manual - Page 19
    INSTALLATION AND CONNECTION 1 . ACC 2 Connector Pin No. - 2 3 4 5 6 7 8 9 10 11 12 13 Pin Name NC RTTY ANO GND PSQ MET 1 NC GND PKS MET2 ANI GND SS Function No connection RTTY control terminal (FSK key input) Audio output • Connect to the audio input of a PC or an external device such as a PC
  • Kenwood TS-890S | Operation Manual - Page 20
    1 INSTALLATION AND CONNECTION . EXT. AT Connector Pin No. 1 2 3 4 5 6 Pin Name GND TT GND NC TS 14S Function Signal ground EXT.AT connector (TTI/TTO) Signal ground No connection EXT.AT connector (TSI/TSO) DC 13.8 V power supply for EXT.AT (4 A
  • Kenwood TS-890S | Operation Manual - Page 21
    ] [MHz] [LSB/USB] [CW/CW-R] [FSK/PSK] [FM/AM] [DATA] Activates the function according to the key guide at the bottom of the screen. (Henceforth represented as F1 [XXX] to F7 [XXX] in this manual.) Refer to "List of Function Key Behaviors (Standard Mode Screen)" for functions of the F key on the
  • Kenwood TS-890S | Operation Manual - Page 22
    the preset value. Press Turns ON/OFF the FINE-tuning function. Activates the function according to the key guide on the right side of the screen. (Henceforth represented as F [XXX] in this manual.) Refer to "List of Function Key Behaviors (Standard Mode Screen)" for functions of the F key on the
  • Kenwood TS-890S | Operation Manual - Page 23
    ...... NAMES AND FUNCTIONS OF PARTS 2 [ M.IN] [] [ ] [MENU] [TF-SET] [MONI] [CAR] [AGC] [NR] [NB1] [NB2] [BC] [NCH] [RIT] [XIT] [CL] Key Press Press Press Press and hold Press Press Press Press Press and hold Press Press Press and hold Press Press and hold Press Press and hold
  • Kenwood TS-890S | Operation Manual - Page 24
    2 NAMES AND FUNCTIONS OF PARTS List of Function Key Behaviors (Standard Mode Screen) Function Keys (Vertically Arrayed) Key Guide Behavior [ANT/PRE] Press Press and hold Switches the preamplifier. (OFF/ PRE 1/ PRE 2) Switches between "ANT 1" and "ANT 2". [ATT] Press Press and hold Switches
  • Kenwood TS-890S | Operation Manual - Page 25
    NAMES AND FUNCTIONS OF PARTS 2 . ........ List of Control Knob Behaviors Control Tuning [MULTI/CH] [RIT/XIT] [KEY] [DELAY] [MIC/PITCH] [POWER] [HI/SHIFT] [LO/WIDTH] [NOTCH] [SQL] [AF] [RF] Behavior Aligns the TX and RX frequencies. Switches the frequency at a fast speed. (Available in the VFO
  • Kenwood TS-890S | Operation Manual - Page 26
    squelch opens upon receiving a signal. Lights up in red when transmission is in progress. Lights up when drive output is ON. Lights up during manual recording (including when recording is paused). Blinks for 1 second at the start of saving the constantly recorded audio. Lights up in the split mode
  • Kenwood TS-890S | Operation Manual - Page 27
    for connecting a PC or LAN when running with the KNS (KENWOOD NETWORK COMMAND SYSTEM) or for automatic correction of the clock time. Connector for connecting a PC. It is used to control this transceiver using the ARCP-890 as well as to input and output signals for transmission and reception
  • Kenwood TS-890S | Operation Manual - Page 28
    Microphone (Optional) A PTT (Push-to-talk) Switch Switches to the transmitting state while this switch is being pressed. Releasing the switch restores the transceiver to the receiving state. B UP/ DOWN Keys For scrolling up/down the items in one of the following modes, such as scrolling up/down
  • Kenwood TS-890S | Operation Manual - Page 29
    Screen ⡣ ⡬ NAMES AND FUNCTIONS OF PARTS 2 ⡤⡥ ⡦ ⡧ Area Display Description Appears when an RX antenna is functioning. Displays the antenna number. Switches the antenna number accordingly when the antenna is switched. Appears when antenna output for the external receiver is functioning.
  • Kenwood TS-890S | Operation Manual - Page 30
    2 NAMES AND FUNCTIONS OF PARTS Area Display Description Displays the antenna tuner function and operating status. > lights up when the antenna tuner is ON during reception. > blinks while antenna tuning is in progress. Appears when the transverter is ON. Refer to 4-11 16-15
  • Kenwood TS-890S | Operation Manual - Page 31
    , and lights up when the USB flash drive is recognized by this transceiver. The icon blinks when writing image data to the USB flash drive function is enabled. 14-4 Appears when a KNS user is connected to this transceiver. 15-2 Displays the selected RX filter (A, B or C). 6-1 Displays the low
  • Kenwood TS-890S | Operation Manual - Page 32
    2 NAMES AND FUNCTIONS OF PARTS Area Display Configuration Screen Bandscope Description Displays the mode that is currently running. "-D" is displayed when in the data mode. "-R" is displayed when in the reverse mode. Appears while receiving in the TX band. Appears while transmitting in the TX
  • Kenwood TS-890S | Operation Manual - Page 33
    3 Menu Operation The settings of the different functions of this transceiver can be changed from the menu. It can also be used SWL USB/File MORE Clock LAN Auto Mode KNS Timer Frequency Marker MORE Key Guide Behavior Sub-Menu Selection 1 RESET Displays the Reset menu screen. ADV. Displays
  • Kenwood TS-890S | Operation Manual - Page 34
    value to the default setting. • Pressing F [MORE] switches the key guide display. • Pressing F [ TOP] when configuring the sub-menu returns the Also, data of the operating environment can be saved to and read from a transceiver or USB flash drive. 2 Press F7 [CONFIG]. A message appears. • Press
  • Kenwood TS-890S | Operation Manual - Page 35
    Wait time for screen saver Preview (5 [sec])/ 5/ 15/ 30/ 60 [min] Preview (5 [sec]) 16-1 Screen saver message Up to 10 alphanumeric characters TS-890 16-1 Power on message Up to 15 alphanumeric characters HELLO 16-1 Meter FM S meter sensitivity Normal/ High Normal 4-10 Analog meter
  • Kenwood TS-890S | Operation Manual - Page 36
    20 (1 step) Sidetone volume Off/ 1 to 20 (1 step) Voice Guide Voice guide volume Off/ 1 to 20 (1 step) Voice guide speed 1 to 4 (1 step) Language of voice guide and message display English/ Japanese Automatic voice guide Off/ On - 2. Decoding & Encoding - Description Setting Value FSK
  • Kenwood TS-890S | Operation Manual - Page 37
    MENU 3 Menu 3-00 3-01 3-02 3-03 3-04 3-05 3-06 3-07 3-08 3-09 3-10 3-11 3-12 3-13 Menu 4-00 4-01 4-02 4-03 4-04 4-05 Menu 5-00 5-01 5-02 5-03 5-04 5-05 - 3. Controls Configurations - Display Description Setting Value Control Rate Frequency Rounding Off (Multi/ Channel Rounds off the frequency
  • Kenwood TS-890S | Operation Manual - Page 38
    5-16 Menu 6-00 6-01 6-02 6-03 6-04 6-05 6-06 6-07 6-08 6-09 6-10 6-11 6-12 6-13 6-14 6-15 - 5. CW Configurations - Display Description Setting Value Weight and Timing Automatic CW TX with Keying in SSB Mode CW transmission by keying in the SSB mode Off/ On Carrier Frequency Offset (SSB Mode
  • Kenwood TS-890S | Operation Manual - Page 39
    MENU 3 Menu 7-00 7-01 7-02 7-03 7-04 7-05 7-06 7-07 7-08 7-09 7-10 7-11 Menu 8-00 8-01 8-02 8-03 8-04 8-05 8-06 8-07 Menu 9-00 9-01 9-02 9-03 - 7. Rear Connectors - Display Description Setting Value Default Refer to Baud Rate Baud Rate (COM Port) Baud rate of COM connector 4800/ 9600/
  • Kenwood TS-890S | Operation Manual - Page 40
    - About Various Software License Agreements Licenses related to software used by this transceiver - Firmware Version Firmware version used by this transceiver - Default TX Power Automatic 50 [%] 50 [%] Internal 0 On Off Off Off 50 Off Off Mute Low Sql Off Flow Control Off Off Off On
  • Kenwood TS-890S | Operation Manual - Page 41
    Value Default Target bands of the linear amplifier menu HF/ 50M/ 70M (E type) HF Linear amplifier ON/OFF Off/ On Off Linear amplifier Internal Memory) Deletes files stored in the internal memory of the transceiver - - File Storage Location Configures the destination for saving files
  • Kenwood TS-890S | Operation Manual - Page 42
    1.0.0.0 to 223.255.255.255 1.0.0.0 to 223.255.255.255 - Default On 192.168.1. 100 255.255.255. 0 Blank Blank Blank Fixed value for each transceiver Refer to 15-1 3-10
  • Kenwood TS-890S | Operation Manual - Page 43
    Timer Menu Items Display Timer Mode Repeat Day of the Week - Sun Day of the Week - Mon Day of the Week - Tue Day of the Week - Wed Day of the Week - Thu Day of the Week - Fri Day of the Week - Sat Power-on Time Power-off Time Frequency/Mode Sleep Timer Auto Mode Menu Items Auto Mode Frequency
  • Kenwood TS-890S | Operation Manual - Page 44
    3 MENU KNS Menu Items Menu 0 Display KNS Operation (LAN Connector) 1 Administrator ID 2 Administrator Password 3 Built-in VoIP 4 Audio Input Level (VoIP) 5 Audio Output Level (VoIP) 6 VoIP Jitter Buffer 7 Speaker Mute 8 Access Log 9 Registered Users' Remote Operation 10 Session
  • Kenwood TS-890S | Operation Manual - Page 45
    regulated DC power supply while leaving the power of the TS-890S on. Current Flow when Power is OFF When the power of the external power supply is ON, a small amount of electric current is flowing even when the power of this transceiver is OFF. The amount of current that flows through when
  • Kenwood TS-890S | Operation Manual - Page 46
    of the noise and surrounding conditions such as temperature. ● The position of the control knob at which noise disappears also varies depending on whether this transceiver is in the FM mode or in other modes. 4-2
  • Kenwood TS-890S | Operation Manual - Page 47
    BASIC OPERATIONS 4 Selecting VFO A/ B This transceiver is equipped with two VFOs, A and B. The two 70 MHz (E type), 135 kHz, 475 kHz, MW broadcast band, and 5 MHz at one touch. • This transceiver comes with a band memory feature that is able to store up to 5 pairs of frequencies and modes (3 pairs
  • Kenwood TS-890S | Operation Manual - Page 48
    ● The mode and DATA mode settings are stored in the band memory. ● FM narrow and normal settings are stored in each of the following band: HF/ 50 MHz/ 70 MHz (E type). 3 Pressing F1 [A.MODE] each time switches the Auto Mode to ON or OFF. When the Auto Mode is turned ON
  • Kenwood TS-890S | Operation Manual - Page 49
    MHz or higher. • The table below shows an example when auto mode frequency is configured to the HF/50/70 MHz band. Frequency 1.620 MHz 2.000 MHz 3.500 MHz 3.525 MHz 10.100 MHz 18.110 MHz 21.000 MHz 21.070 MHz 21.125 MHz 21.150 MHz 24.890 MHz 24.930 MHz 28.000 MHz 28.070 MHz 28.150 MHz 28.200 MHz
  • Kenwood TS-890S | Operation Manual - Page 50
    4 BASIC OPERATIONS Frequency Adjustment Using the [MULTI/CH] Control Turning the [MULTI/CH] control enables the frequency to be changed quickly. The frequency increases or decreases in increments based on the configured step size. Turn the [MULTI/CH] control to increase or decrease the frequency.
  • Kenwood TS-890S | Operation Manual - Page 51
    input of frequency is complete. Frequency Input History The latest 10 frequency values that were input using the numeric keypad are stored in the transceiver. To use the same frequency value, it is possible to retrieve it from the history. 1 Press [ENT] to enable input of a frequency value. "-" is
  • Kenwood TS-890S | Operation Manual - Page 52
    output level, while turning it to the left reduces the output level. The selectable range varies with the band and mode in use as follows. HF Band 50 MHz Band 70 MHz Band (E type) Other than AM 5 to 100 [W] 5 to 100 [W] 5 to 50 [W] AM 5 to 25 [W] 5 to 25 [W] 5 to 12.5 [W] ● Output
  • Kenwood TS-890S | Operation Manual - Page 53
    BASIC OPERATIONS 4 TX Output Power Limiter Meter The TX output power limiter can be used to limit the TX output power. This is a function to prevent the TX output power level from exceeding the preconfigured level for each band when the [POWER] control is turned. It can also be used to limit TX
  • Kenwood TS-890S | Operation Manual - Page 54
    as that in the other modes. Selecting "High" switches the transceiver to the same deflection type (high sensitivity) as our conventional models type) RX Antenna Select an RX antenna. To use an RX antenna such as an HF low-band Beverage antenna or a directional loop antenna, connect it to the RX IN
  • Kenwood TS-890S | Operation Manual - Page 55
    Size" setting. Band/Mode CW/FSK/PSK/SSB/FM/ SSB-DATA/FM-DATA HF AM/AM-DATA CW/FSK/PSK/SSB/FM/ SSB-DATA/FM-DATA 50M AM/ an external antenna tuner. 3 Press and hold [AT] to perform tuning. • The transceiver switches to the CW mode and starts tuning. TX output power is automatically configured to 10
  • Kenwood TS-890S | Operation Manual - Page 56
    to the AT connector and ANT 1 is used, the signal bypasses the built-in antenna tuner circuit. ● Production of the AT-300 has been discontinued. TS-890S ANT 1 Connector . AT-300 4-12
  • Kenwood TS-890S | Operation Manual - Page 57
    operation" is used in cases such as when using an FM repeater or when calling a DX station. 1 Press [SPLIT]. > lights up when the transceiver enters the split mode. Turning the Tuning Control to Search for a TX Frequency To search for a TX frequency by turning the Tuning control, perform
  • Kenwood TS-890S | Operation Manual - Page 58
    is configured to FAST, MID or SLOW according to the receiving status and operation mode (other than FM mode). • The digital AGC circuit of this transceiver divides the time constant into 20 levels from SLOW to FAST, with "1" being the fastest and "20" the slowest. • Generally, the time constant is
  • Kenwood TS-890S | Operation Manual - Page 59
    ● This function may not be effective for pulse noise occurring in short time interval. ● Configuring to a value with a high threshold level may cause the transceiver to malfunction and distort the RX audio depending on the condition of the RX signal. 5 Press and hold [AGC] or press [ESC] to end the
  • Kenwood TS-890S | Operation Manual - Page 60
    ● When the RX DSP equalizer is OFF, "OFF" is displayed at the lower end of the key guide. Adjusting the Equalizer Characteristics The equalizer characteristics can be customized according to the user's preferences. Also, the customized characteristics can be stored as user-defined
  • Kenwood TS-890S | Operation Manual - Page 61
    depending on the destination for saving files.) • USB flash drive: "KENWOOD\TS-890\SETTINGS \RX_EQ" • Built-in memory: "SETTINGS\RX_EQ" ● When the data to a USB flash drive, insert a USB flash drive formatted using this transceiver into (USB-A). 1 Press and hold F [RX EQ] to display the RX
  • Kenwood TS-890S | Operation Manual - Page 62
    5900 7200 9400 AM 11600 13570 15100 17480 18900 21450 25670 • The band segments of the SWL mode that is preconfigured on this transceiver are represented in a slightly different way compared to conventional meter bands. Different band segments are used so as to achieve wider coverage to
  • Kenwood TS-890S | Operation Manual - Page 63
    steps within the ±9.99 kHz range without altering the TX frequency. This is used such as when the TX frequency of the station that this transceiver is communicating with has become slightly deviated. • When the FINE mode is ON, the offset frequency of RIT switches to a step size of 1 Hz. RIT
  • Kenwood TS-890S | Operation Manual - Page 64
    type of digital communication that combines the use of "dots" and "dashes". • The built-in electronic keyer of this transceiver offers a wide variety of functions to support the operation of the users. For more details, please refer to "Electronic Keyer" (5-13). 1 Select band and frequency. Select
  • Kenwood TS-890S | Operation Manual - Page 65
    COMMUNICATING AIDS 5 Adjusting the Sidetone and Pitch Frequency • During key-down in the CW mode, a tone can be heard from the speaker of this transceiver. This tone is known as a sidetone. When this tone is heard, it means it is possible to monitor the Morse code transmitted by one's own
  • Kenwood TS-890S | Operation Manual - Page 66
    Set to the CW mode. 2 Press F3 [DECODE] to display the CW communication screen. • If F3 [DECODE] is not displayed in the key guide, press [ESC] to exit the configuration screen and bandscope. Decoding in Progress (Decodes and Displays the Received Signal) Encoding in Progress (Analyzes and Displays
  • Kenwood TS-890S | Operation Manual - Page 67
    added to the TX/ RX details display area. (5-28) • This transceiver does not support Japanese characters. • Press [Page Up] / [Page Down] on the mode. • If F6 [THLD] is not displayed in the key guide, press F1 [MORE] to toggle the key guide display. 2 Press F4 [-]/ F5 [+] or turn the [MULTI/CH
  • Kenwood TS-890S | Operation Manual - Page 68
    F5 [CH 8] are not displayed in the key guide, press F1 [MORE] to toggle the key guide display. • Press F7 [NEXT] to switch existing character string. • Message CH supports only messages registered via text input or "repeat wait" state and returns the transceiver to the decoding state. • While >
  • Kenwood TS-890S | Operation Manual - Page 69
    COMMUNICATING AIDS 5 Electronic Keyer This transceiver comes with a built-in electronic keyer that can be used simply by connecting a paddle to the [KEY] control, the TX output power display shows the keying speed for a duration of 2 seconds. ● Only dots are supported in the bug key mode. 5-13
  • Kenwood TS-890S | Operation Manual - Page 70
    manual weighting" mode and not affected by the keying speed. • When [2.5] (1:2.5) to [4.0] (1:4) is selected, the dot-dash weight to 60 Weight 1:3.2 1:3.0 1:2.8 CW Message Memory This transceiver comes with this transceiver is in a mode other than CW, F2 [KEYER] is not displayed in the key guide.
  • Kenwood TS-890S | Operation Manual - Page 71
    COMMUNICATING AIDS 5 3 Use the function keys, [MULTI/CH] control or USB keyboard to enter a CW message. • Enter a message that contains not more than 50 characters. The default setting is blank. Key F1 [SPACE] F2 [-]/ F3 [+] F4 [ ]/ F5 [ ] F [BACK SPACE] F [DEL] F [CHAR] Behavior Inserts a space.
  • Kenwood TS-890S | Operation Manual - Page 72
    8 Playing/Transmitting CW Messages This transceiver can be configured as follows to it is configured to "Text String". Descriptions in this manual are based on the "Paddle" setting, but the steps displayed and F6 [-1] is also not shown in the key guide. ● When Menu [5-14] "Channel Number (Count-up
  • Kenwood TS-890S | Operation Manual - Page 73
    Interval Time" Setting Value 0 to 10 (default) to 60 [s] (1 step) Configuring to a larger value lengthens the playback interval. RTTY Operation This transceiver comes with a built-in demodulator for RTTY operation, a RX decoder and a TX encoder. It is possible to operate in RTTY (FSK) independently
  • Kenwood TS-890S | Operation Manual - Page 74
    cross patterns bisect at right angles (90 degrees) when this transceiver is correctly tuned to the signal. Threshold Level Displays the [THLD] F5 [MEMORY] F6 [X-Y LEV] F7 [EXTEND] Behavior Switches the key guide. Pauses update (drawing) of the TX/RX details display area. Pressing the key again
  • Kenwood TS-890S | Operation Manual - Page 75
    on the USB keyboard to send out the character string. • Character strings that are stored in the character string buffer are sent out by this transceiver. • Upon entering the TX mode, the [BUSY/TX] LED lights up in red, and > is displayed in the status bar. • In the character string buffer
  • Kenwood TS-890S | Operation Manual - Page 76
    ensure that the character string (RTTY message) is forwarded to the character string buffer, followed by pressing [F12] on the USB keyboard. ● To switch this transceiver to the RX mode after transmitting an RTTY message for which "AUTO RX" is set to OFF, press [F12] on the USB keyboard after the
  • Kenwood TS-890S | Operation Manual - Page 77
    to the function key is being transmitted automatically. • If the channel guide is not displayed, press F2 [MORE]. • Pressing F7 [NEXT] RTTY message that is indicated by an > display beside it, this transceiver returns to the RX mode. Settings Related to RTTY Encode/Decode Enabling Decode
  • Kenwood TS-890S | Operation Manual - Page 78
    Peak Filter Using the audio peak filter may help to improve the decodability of RTTY messages when operating in the RTTY (FSK) mode with this transceiver connected to an external device. Press F [APF] to set the audio peak filter to ON. • When audio peak filter is turned on, "ON" is displayed
  • Kenwood TS-890S | Operation Manual - Page 79
    F1 [MORE] F2 [B/QPSK] F3 [31/63] F3 [PAUSE] F4 [LOG] F4 [(CLEAR)] F5 [THLD] F5 [MEMORY] F6 [AFC] F7 [EXTEND] Behavior Switches the key guide. Switches between the BPSK and QPSK modes. Switches between the PSK31 and PSK63 modes. Pauses update (drawing) of the TX/RX details display area. Pressing
  • Kenwood TS-890S | Operation Manual - Page 80
    5 COMMUNICATING AIDS FFT Scope/Vectorscope Display Setting The tuning scope displayed on the PSK communication screen can be switched to an "FFT scope" or "vectorscope" display. Configure in Menu [2-13] "PSK Tuning Scope" Setting Value FFT Scope (default)/ Vector Scope • The display toggles
  • Kenwood TS-890S | Operation Manual - Page 81
    COMMUNICATING AIDS 5 Switching between PSK31 and PSK63 This transceiver supports PSK31 as well as PSK63. The latter has a transfer rate that is twice that of selected in Menu [9-01]. To input Japanese characters, please download and refer to the Japanese instruction manual from our website. 5-25
  • Kenwood TS-890S | Operation Manual - Page 82
    F2 [MORE] to toggle the key guide display. 4 Press F5 [MSG]. Configuring Auto TX/RX for the PSK Message Memory The transmission and reception behavior can be configured when a PSK message memory channel is selected. • Auto TX places this transceiver in the TX mode before transmitting a message
  • Kenwood TS-890S | Operation Manual - Page 83
    if auto TX is set to OFF. • If the channel guide is not displayed, press F2 [MORE]. • Pressing F7 When the communication log function is ON and the transceiver is in the standby mode, " " is • CW: KENWOOD\TS-890\DECODE\CW • RTTY: KENWOOD\TS-890\DECODE\RTTY • PSK: KENWOOD\TS-890\DECODE\PSK ●
  • Kenwood TS-890S | Operation Manual - Page 84
    as communication that is noise-resistant. Communication in the FM mode is also supported on the 29 MHz, 50 MHz and 70 MHz (E type) bands. the zone. 9 Press [SEND] or release [PTT] on the microphone. Doing so places this transceiver in the RX mode. 10 Press F1 [ ]. ● When using a microphone with a low
  • Kenwood TS-890S | Operation Manual - Page 85
    details on the memory channel settings, please refer to "MEMORY CHANNELS" (9-1). ● The tone frequency may vary depending on the country or region this transceiver is being used. Selecting a Tone Press F4 [TONE] to select "TONE". Pressing F4 [TONE] each time toggles the tone signal selection in the
  • Kenwood TS-890S | Operation Manual - Page 86
    Squelch opens upon receiving a CTCSS tone for which the FM wave is superimposed with the same CTCSS tone frequency as that configured on this transceiver. • During CTCSS frequency scan, it is possible to detect the CTCSS tone frequency that is contained in the RX signal. • When a signal is received
  • Kenwood TS-890S | Operation Manual - Page 87
    status of the attenuator (attenuation level) is displayed in the key guide. Filter Scope The following information is displayed on the filter scope screen The setting for the band characteristics of the RX filter on this transceiver can be switched at one touch according to the operating status to
  • Kenwood TS-890S | Operation Manual - Page 88
    6 REJECTING INTERFERENCE Configuring the RX Filter The steps to configure the settings for the different types of RX filters are as follows. Selecting a Roofing Filter A roofing filter helps to reduce strong interference signals that are next to the target signal. 1 Press and hold [IF FIL] to
  • Kenwood TS-890S | Operation Manual - Page 89
    Configuring the Behavior of the HI/SHIFT and LO/ WIDTH Controls (SSB/SSB-DATA Only) The high cutoff/low cutoff selection in the SSB mode and Shift/ Width selection in the SSB-DATA mode are preconfigured in the default setting, but they can be changed in the menu. SSB Mode Configure in Menu [6-11] "
  • Kenwood TS-890S | Operation Manual - Page 90
    .. 6 REJECTING INTERFERENCE Changing the Passband Width and Shift Amount When in the CW or SSB-DATA mode, the passband width and shift amount of the DSP filter can be altered. When in the RTTY (FSK) or PSK mode, the passband width can be changed. The passband width can be changed so that the
  • Kenwood TS-890S | Operation Manual - Page 91
    and WIDTH/SHIFT) can be preset according to the style in which this transceiver is used. 1 Press and hold [IF FIL] to display the RX between ON and OFF. • When audio peak filter is on, "ON" is displayed on the key guide. "OFF" is displayed when the audio peak filter is turned off. 3 Press F2[ ]/ F3[
  • Kenwood TS-890S | Operation Manual - Page 92
    . • When audio peak filter is on, "ON" is displayed on the key guide. "OFF" is displayed when the audio peak filter is turned off. ● When the . Noise Blanker The noise blanker is used to reduce pulse noise. This transceiver is equipped with two types of noise blankers: NB1 that employs analog signal
  • Kenwood TS-890S | Operation Manual - Page 93
    and hold [NB2] or press [ESC] to end the process. ● Configuring to a value with a higher level of noise blanker effect may cause the transceiver to malfunction and distort the RX audio depending on the condition of the RX signal or interfering signal. Configuring the Blanking Duration (Type B Only
  • Kenwood TS-890S | Operation Manual - Page 94
    point has been set in the CW mode, altering the PITCH and SHIFT values will not change the notch point set for beat suppression. This transceiver comes with two types of noise reduction functions NR1 and NR2 which are effective for reducing continuous noise. When NR1 is used, the optimal method
  • Kenwood TS-890S | Operation Manual - Page 95
    REJECTING INTERFERENCE 6 Configuring the NR1 Effect Level Beat Canceler 1 Press [NR] to select Noise Reduction 1. 2 Press and hold [NR] to display the Noise Reduction 1 effect level configuration screen. Beat canceler is capable of suppressing multiple periodic interfering signals (beats) within
  • Kenwood TS-890S | Operation Manual - Page 96
    . 6-10
  • Kenwood TS-890S | Operation Manual - Page 97
    frequency on the horizontal axis, the bandscope provides a visual representation of the condition of the RX frequency band. • The bandscope of this transceiver comes in the following 3 modes. Auto Scroll Mode: A mode where the lower and upper frequency limits of the frequency band to be displayed
  • Kenwood TS-890S | Operation Manual - Page 98
    step) 3 Press F5 [REF.LEV] to end adjustment of the reference level. ● The reference level is slightly compensated for each span internally on this transceiver so that the view of the waterfall does not change even when the display frequency span switches. For this reason, the height of the waveform
  • Kenwood TS-890S | Operation Manual - Page 99
    desired position using the [MULTI/CH] control. • Pressing and holding F4 [SHIFT] moves the shift position to the center. 3 Press F4 [SHIFT]. The transceiver exits the shift position configuration mode. ● When observing the condition of the frequency calling the DX station or the condition in the RX
  • Kenwood TS-890S | Operation Manual - Page 100
    7 SCOPE FUNCTIONS .. Expand This function expands the frequency range for spectral analysis to prevent the waterfall display from being interrupted when the frequency is changed while in the auto scroll mode or center mode (when the waterfall display during tuning is configured to "Straight").
  • Kenwood TS-890S | Operation Manual - Page 101
    .00 26.00 ≦ f ＜ 30.00 30.00 ≦ f ＜ 60.00 30.00 ≦ f ＜ 74.80 Range No. 1 2 3 1 2 3 1 2 3 1 2 3 Default Default Lower Limit Upper Limit [MHz] [MHz] 24.890 24.890 24.930 28.000 28.000 28.300 (K type) 28.200 (E type) 50.000 50.000 50.100 70.000 70.000 70.250 24
  • Kenwood TS-890S | Operation Manual - Page 102
    7 SCOPE FUNCTIONS Touchscreen Tuning This function enables signals to be received by touching the desired point in the spectrum scope display area or waterfall display area. • When in the Auto Scroll mode and Fixed mode, touching a point moves the marker to the corresponding frequency. • When in
  • Kenwood TS-890S | Operation Manual - Page 103
    SCOPE FUNCTIONS 7 Deleting a Registered Frequency 1 Press F2 [ ]/ F3 [ ] or turn the [MULTI/CH] control to select the frequency to delete. 2 Press and hold F5 [(DELETE)] to delete. Turning ON/OFF Marker Function 1 Press [MENU]. 2 Press F [F.MKR]. • If F [F.MKR] is not displayed, press F [MORE] to
  • Kenwood TS-890S | Operation Manual - Page 104
    .. . . 7 SCOPE FUNCTIONS Audio Scope The TX/RX audio can be displayed on an "audio scope screen" where a spectrum scope and an oscilloscope are displayed as well as on a "multi scope screen" where a reduced display of the bandscope appears at the top together with the "audio scope screen".
  • Kenwood TS-890S | Operation Manual - Page 105
    ACC 2, (USB-B) and LAN connectors on the rear panel of this transceiver can be configured. Audio Source Input MIC ACC 2 USB Audio LAN Description , sound that is emitted by the audio source might trigger transmission by this transceiver. ● These are common settings for the SSB, AM and FM modes.
  • Kenwood TS-890S | Operation Manual - Page 106
    gain of the input data from the ANI terminal of the ACC 2 connector, (USB-A or USB-B) or LAN connector on the rear panel of this transceiver can be adjusted in the Data VOX mode. 1 Press and hold [VOX] to display the VOX configuration screen. 4 Press F6 [-]/ F7 [+] or turn the [MULTI
  • Kenwood TS-890S | Operation Manual - Page 107
    In the FSK and PSK modes, FSK and PSK signals transmitted by this transceiver can be monitored. Press [MONI] to turn the TX monitor ON or AM-DATA • FSK/ PSK • Each time there is a change in the mode, the transceiver switches back to the TX monitor ON/OFF status stored in each group. TX monitor is
  • Kenwood TS-890S | Operation Manual - Page 108
    functions with respect to audio input from the ANI terminal of the ACC 2 connector or the (USB-B) connector on the rear panel of this transceiver. Configuring the Speech Processor Input Level 1 Press and hold F [PROC] to display the Speech Processor configuration screen SSB/SSB-DATA/AM/AM-DATA
  • Kenwood TS-890S | Operation Manual - Page 109
    mode. 2 Press F [TX EQ]. Pressing F [TX EQ] each time toggles the TX equalizer between ON and OFF. ● The TX equalizer turns OFF automatically when this transceiver is configured to a mode other than SSB, AM or FM. 8-5
  • Kenwood TS-890S | Operation Manual - Page 110
    FUNCTIONS Selecting a Frequency Characteristic for the TX Equalizer This transceiver comes with 6 types of frequency characteristics for the TX FP BB1 BB2 C Frequency (Hz) 3 Press F5 [COPY]. A message with instructions on how to specify the destination for saving the settings is displayed. 8-6
  • Kenwood TS-890S | Operation Manual - Page 111
    save the data to a USB flash drive, insert a USB flash drive formatted using this transceiver into (USB-A). 1 Press and hold F [TX EQ] to display the TX Equalizer screen on the destination for saving files.) USB flash drive: "KENWOOD\TS-890\SETTINGS\RX_EQ" Built-in memory: "SETTINGS\RX_EQ" ● When
  • Kenwood TS-890S | Operation Manual - Page 112
    duration from the time transmission starts is exceeded. Configure in Menu [6-05] "ID Beep" Setting Value Off (default)/ 1 to 30 [min] (1 step) ● The transceiver may not function as intended in some cases as it may return to the receiving state during CW break-in or VOX transmission. Adjusting TX
  • Kenwood TS-890S | Operation Manual - Page 113
    9 MEMORY CHANNELS MEMORY CHANNELS 9 This transceiver comes with 120 memory channels, each of which can be used for registering operating data. The 120 memory channels are divided into 3 types which are
  • Kenwood TS-890S | Operation Manual - Page 114
    the microphone or turn the [MULTI/CH] control to switch to the target memory channel. 3 Pressing [M/V] again exits the memory channel mode. The transceiver returns to the VFO mode. Direct Entry of a Memory Channel Number A memory channel number can be selected by pressing the corresponding number on
  • Kenwood TS-890S | Operation Manual - Page 115
    [M VFO] to copy the operating data to the VFO. • After operating data is copied to a VFO, the data at the source will be erased. • The transceiver exits the memory channel mode and enters the VFO mode. • Operating data of memory channels assigned to specific band segments cannot be copied to a VFO
  • Kenwood TS-890S | Operation Manual - Page 116
    the end frequency. 6 Press F4 [M.IN] or [ M.IN] to register the end frequency. The end frequency is registered to "Frequency 2" and the transceiver exits the Memory Channel List screen. Erasing Memory Channels Registering a Memory Channel Name Each memory channel can also be assigned with a name
  • Kenwood TS-890S | Operation Manual - Page 117
    number. 2 Turn the [MULTI/CH] control to switch the quick memory channel. • Pressing [Q-MR>] again exits the quick memory channel mode and returns the transceiver to the VFO mode. . ● When data is retrieved from a memory channel for use or when operating data is not registered to the quick memory
  • Kenwood TS-890S | Operation Manual - Page 118
    is to be copied. 3 Press and hold [M/V], or press F6 [M VFO]. • Operating data is copied from the quick memory channel to the VFO and the transceiver switches to the VFO mode. • When the operating data is temporarily changed, the altered operating data is copied to the VFO. 9-6
  • Kenwood TS-890S | Operation Manual - Page 119
    10 SCAN SCAN 10 Scan is a function that searches for signals by automatically altering the frequency. This transceiver makes use of the following scan methods to search for signals. Scan Type Program Scan Normal Scan VFO Scan Scan Using Memory Channels All-Channel
  • Kenwood TS-890S | Operation Manual - Page 120
    10 SCAN ● Examples on the configuration of Program Scan and VFO Scan: • Configure the memory channels for specific band segments such that the checkboxes for P1, P3 and P5 are selected. Next, press F5 [SCAN]. Program Scan starts and scanning is performed in the frequency range registered for the
  • Kenwood TS-890S | Operation Manual - Page 121
    SCAN 10 5 Turn the Tuning control and align the "Current" frequency as the frequency point for Program Slow Scan. 6 Press any of the function keys (F2 [POINT 1] to F6 [POINT 5]) to configure the center point of the preferred frequency range to perform Program Slow Scan. • Pressing and holding the
  • Kenwood TS-890S | Operation Manual - Page 122
    10 SCAN ● Pressing F5 [SCAN] does not start the scan operation when the memory groups to be scanned are configured as follows. • When the checkboxes for all the memory groups are deselected. • When operating data is not stored in the memory channels of a memory group, even if the checkboxes of the
  • Kenwood TS-890S | Operation Manual - Page 123
    transceiver is recognized on the PC as a removable device with the name "TS-890". The folder configuration of the "TS-890" removable device is as follows. TS-890 TS-890" removable device. Folder Configuration of the USB Flash Drive KENWOOD TS-890 manual of this transceiver supports the USB
  • Kenwood TS-890S | Operation Manual - Page 124
    of manual recordings, full-time recordings and timer recordings • Settings data files of TX and RX equalizers • CW/TTY/PSK communication log files • KNS communication log files • Image files for screen savers (Type 3) ● The destination folder cannot be selected. • USB flash drive: "\KENWOOD\TS-890
  • Kenwood TS-890S | Operation Manual - Page 125
    Memory" data (CW/RTTY/ PSK message memory) • "Voice Message Memory" data (voice message data) ● If the settings data file is saved in a transceiver with a newer firmware version, pressing F4 [OK] in step 7 will result in an error. A "data reading error screen due to mismatch between new and old
  • Kenwood TS-890S | Operation Manual - Page 126
    in Memory The file name of the settings data that is stored on the transceiver can be changed by the user to ease identification. 1 Press [MENU]. 2 Log Files Description Settings data file Audio files of manual and full-time recordings Audio files of timer name "TS-890" appears on the PC. 11-4
  • Kenwood TS-890S | Operation Manual - Page 127
    the PC. Then, a removable device with the name "TS-890" appears on the PC. ● When a remote user be deleted coincides with an item for which manual recording or CW/RTTY/PSK communication log up when the USB flash drive is recognized by this transceiver. 2 Select "Format USB Flash Drive" in the
  • Kenwood TS-890S | Operation Manual - Page 128
    the display returns to the USB/File Management menu screen. ● While manual recording or CW/RTTY/PSK communication log recording is in progress, Removing the USB Flash Drive When removing a USB flash drive from this transceiver, make sure to follow the steps below to remove the device safely.
  • Kenwood TS-890S | Operation Manual - Page 129
    handy during DX-pedition or contest operation where repeated calls need to be made over a long period of time or for adjusting an antenna or transceiver by transmitting a test radio wave. The maximum recording time is 100 seconds. In other words, recording to all the channels is possible up to
  • Kenwood TS-890S | Operation Manual - Page 130
    12 VOICE MESSAGE/AUDIO FILE Registering a Name for a Voice Message Recorded voice messages can be assigned with a name. 1 Press F2 [TX MSG] to display the Voice Message screen. Playing Back a Voice Message Follow the steps below to play back a recorded voice message. 1 Select a voice message
  • Kenwood TS-890S | Operation Manual - Page 131
    communication or play back the recordings. Recording functions that can be used on this transceiver are as follows. Manual Recording • Voice recordings up to 9 hours per file can be stored in the builtin memory of this transceiver. As the built-in memory is also used by other functions, the maximum
  • Kenwood TS-890S | Operation Manual - Page 132
    the preconfigured maximum duration (number of seconds) for full-time recording. ● Pressing F1 [RX PLAY] does not activate full-time recording if manual recording is in progress. ● When the remaining memory at the destination for storing the file is running out, a "Insufficient memory space" message
  • Kenwood TS-890S | Operation Manual - Page 133
    or a USB flash drive. To use a USB flash drive, insert it into (USB-A) in advance and check to ensure that it is recognized by this transceiver. 1 Press F1 [RX PLAY] to display the audio recording file screen. 2 Press F7 [INT.MEM] or F7 [USB.MEM] to toggle between the screens for
  • Kenwood TS-890S | Operation Manual - Page 134
    Renaming an Audio File The name of audio files saved via manual recording, full-time recording or timer recording can be changed. , insert it into (USB-A) in advance and check to ensure that it is recognized by this transceiver. 1 Press F1 [RX PLAY] to display the audio file screen. 2 Press F2[ ]/
  • Kenwood TS-890S | Operation Manual - Page 135
    13 VOICE GUIDANCE VOICE GUIDANCE 13 This transceiver comes with a voice guidance that sends out a voice notification of the operating status that is displayed on the screen. The voice guidance content is described in the following style in this manual. Voice Numeric values and alphabets Options
  • Kenwood TS-890S | Operation Manual - Page 136
    output level: "Processor"+ "Out" + Value * No voice is output during adjustment of the sidetone/pitch frequency. Operation on This Key Operation Transceiver Content of Voice Guidance [DELAY] control operation Turn [DELAY] • When adjusting the break-in delay time: "Full" + "Break-in" in the
  • Kenwood TS-890S | Operation Manual - Page 137
    VOICE GUIDANCE 13 Pressing "VOICE1" outputs an announcement as follows. The content of the announcement varies with the screen that is being displayed. Announcements Related to Operating Frequency (Including Content of Auto Announcements) Screen VFO mode *4 Memory channel mode *4 Quick memory
  • Kenwood TS-890S | Operation Manual - Page 138
    13 VOICE GUIDANCE Screen Selection of file to read Selection of data to read (DATA) Processing (without CANCEL key) Data reading complete Request to get ready the USB flash drive Data saving complete TX audio source input settings VOX level configuration TX output power limiter configuration Speech
  • Kenwood TS-890S | Operation Manual - Page 139
    VOICE GUIDANCE 13 Screen CW message (paddle version) Standby for CW message (paddle) registration During CW message registration CW message (text version) RTTY communication PSK communication RTTY/PSK message Log file selection Log View FM tone frequency configuration FM CTCSS frequency
  • Kenwood TS-890S | Operation Manual - Page 140
    13 VOICE GUIDANCE Screen FM cross tone frequency configuration RX filter configuration Audio peak filter configuration Operation/Status When screen is displayed or when [VOICE1] is pressed TONE/CTCSS switching Change in frequency When screen is displayed or when [VOICE1] is pressed Switching of
  • Kenwood TS-890S | Operation Manual - Page 141
    VOICE GUIDANCE 13 Screen Operation/Status Content of Announcement When screen is displayed or when [VOICE1] is pressed During normal selection Blank channel: "Memory" + "List" + Number + "Blank" Simplex mode: "Memory" + "List" + Number + Frequency Split mode: "Memory" + "List" + Number + "Split
  • Kenwood TS-890S | Operation Manual - Page 142
    13 VOICE GUIDANCE Screen Operation/Status Content of Announcement When screen is displayed or when [VOICE1] is pressed When browsing audio files: "Audio" + "File" When browsing audio files of timer recordings: "Audio" + "File" + "Timer" When a selection is made Year (2018 to 2099) + Month +
  • Kenwood TS-890S | Operation Manual - Page 143
    VOICE GUIDANCE 13 Screen Operation/Status Content of Announcement When screen is displayed or when [VOICE1] is pressed "Programmable" + "Timer" + [On/ Off] "Programmable" + "Timer" + "Repeat" + [On/ Off] "Programmable" + "Timer" + Day + [On/ Off] "Programmable" + "Timer" + "Mode" + [Timer Off/
  • Kenwood TS-890S | Operation Manual - Page 144
    menu license display When screen is displayed or when [VOICE1] is pressed Version display for When screen is displayed or advanced menu firmware when [VOICE1] is pressed Switching of operating environment data When screen is displayed or when [VOICE1] is pressed Error/warning message When
  • Kenwood TS-890S | Operation Manual - Page 145
    " + Value (0 to 100) * D: Dimmer [D/L] + Value *D: Display/ L: LED Value "Linear Amplifier" + Target bands of linear amplifier menu + Function name of focusing position + Setting [HF/ 50/ 70 (E type only)] + "Mega Hertz" [Off/On] [Low/ High] [Off/ On] [5/ 10/ 15/ 20/ 25/ 30/ 35/ 40] [5/ 10/ 15/ 20
  • Kenwood TS-890S | Operation Manual - Page 146
    13 VOICE GUIDANCE Voice 2 Pressing the key that is assigned with "VOICE2" announces the S meter and power meter values. For example, "S5" or "20 dB" will be announced in this case. Press [PF B] or the PF key that is assigned with "VOICE2". Announces the S meter and power meter values. ● Pressing
  • Kenwood TS-890S | Operation Manual - Page 147
    Time Follow the steps below to configure the local clock time. This is usually configured to the local time of the location where this transceiver is being operated. 1 Select Clock Menu [01] "Time (Local Clock)". 2 Press F4 [EDIT]. 3 Use the numeric keypad, function keys and the [MULTI/CH] control
  • Kenwood TS-890S | Operation Manual - Page 148
    For a home LAN that uses a broadband router, ensure that port 123 of the broadband router is open. • Configure the network and IP address on this transceiver. For more details on the method of configuration, please refer to "LAN" (15-1). • Configure the address of the NTP server. • Configure the NTP
  • Kenwood TS-890S | Operation Manual - Page 149
    . The default setting is "Off". 4 Press F6 [OK]. Correcting the Date and Time Manually The date and time that is configured for the clock of this transceiver can be corrected by connecting this transceiver manually to the NTP server. 1 Select Clock Menu [1] "Automatic Time Correction". 2 Press F4
  • Kenwood TS-890S | Operation Manual - Page 150
    14 CLOCK DISPLAY/TIMER Timer This transceiver supports programmed operation using the following timer functions. The frequency and mode can be configured in the Program Timer screen. Power ON (Program Timer Configuration Screen) Turns on this transceiver with the preconfigured frequency and mode at
  • Kenwood TS-890S | Operation Manual - Page 151
    Timer menu screen. 8 Press [ESC] to end the process. 9 If the timer (excluding Power-off timer) is set to ON, press [ ] to power off this transceiver. • If a timer mode other than "Off" is configured, the [POWER] LED lights up in orange. CLOCK DISPLAY/TIMER 14 ● Before pressing F5 [COPY] to copy
  • Kenwood TS-890S | Operation Manual - Page 152
    in the RX mode for the preconfigured time interval. "CHECK" is output in the Morse code from the speaker 1 minute before the power of this transceiver turns off. Configure in Menu [0-32] "Automatic Power Off" Setting Value Off (default)/ 60/ 120/ 180 [min] ● Upon reaching the preconfigured APO time
  • Kenwood TS-890S | Operation Manual - Page 153
    Service Provider Ethernet Cable (Straight Type) PC 1 ARCP-890 Radio Control Program TS-890S PC 2 ARHP-890 Radio Host Program When operating this transceiver via the KNS (KENWOOD etc.) from the DHCP server. Besides acquiring the IP address manually, this DHCP can also be used to configure the IP
  • Kenwood TS-890S | Operation Manual - Page 154
    explanation on the areas of the transceiver configuration. For details on specific configurations, please refer to "TS-890S KENWOOD NETWORK COMMAND SYSTEM Setting Manual". Remote PC with ARCP-890 VoIP Application Host PC VoIP Application Voice TS-890S Figure 2: System Configuration when Using
  • Kenwood TS-890S | Operation Manual - Page 155
    to the "TS-890S KENWOOD NETWORK COMMAND SYSTEM Setting Manual". Configuration for KNS Operation in a Home LAN Environment To operate the TS-890S remotely in a radio equipment in the case of a club station). • To connect the transceiver to LAN and perform remote operation from a PC via LAN, login
  • Kenwood TS-890S | Operation Manual - Page 156
    TS-890S KENWOOD NETWORK COMMAND SYSTEM Setting Manual". • Check that the TX operation setting in the modulation line selection for ARCP-890 matches the audio input of the modulation line configured on this transceiver adjust this item when there is a problem with the voice quality of VoIP. Selecting
  • Kenwood TS-890S | Operation Manual - Page 157
    [-]/ F3 [+] to select "On". • When a USB flash drive is selected as the destination for storing the file, create a communication log file in the "\KENWOOD\TS-890\KNS_LOG" folder and record the logs to this file. • When the built-in memory is selected as the destination, the communication log file is
  • Kenwood TS-890S | Operation Manual - Page 158
    will take effect at the next login. KNS Welcome Message A text message notification for the remote user can be written to the transceiver in advance and displayed on the ARCP-890 used by the remote user. A text message notification from a remote user to other remote users can be written to the
  • Kenwood TS-890S | Operation Manual - Page 159
    screen saver. This transceiver comes with 3 types of screen savers. Configuring to the Type 2 screen saver allows a manually input text to Copy the images into the "KENWOOD\TS-890\IMAGE" folder of the USB flash drive using a PC. 2 Connect the USB flash drive to this transceiver. 3 Press [MENU]. 4
  • Kenwood TS-890S | Operation Manual - Page 160
    be displayed on the screen can be manually input. The input text will be contains not more than 10 characters. The default text is "TS-890". Key Behavior F1 [SPACE] Inserts a space. F2 [-]/ be assigned with different functions of this transceiver. Assigning frequently-used functions or menus
  • Kenwood TS-890S | Operation Manual - Page 161
    . OTHER FUNCTIONS 16 Assigning Functions to the PF Keys (KEYPAD Jack) The KEYPAD jack on the rear panel can be used to connect a selfmade selector. Configure using one of the menus between [0-18] "External PF 1: Key Assignment" and [0-25] "External PF 8: Key Assignment". To create a self-made PF
  • Kenwood TS-890S | Operation Manual - Page 162
    and hold Deletes all quick memory data REC Press Starts or pauses manual recording Press and hold Writes full-time recording data to a file Starts the voice guide (VOICE1 function) VOICE2 Press Starts the voice guide (VOICE2 function) VOICE3 Press Starts the voice guide (VOICE3 function
  • Kenwood TS-890S | Operation Manual - Page 163
    Configuring the USB Keyboard The ARCP-890 radio control program, ARHP-890 radio host program, ARUA-10 USB audio control program and PC commands are used to control this transceiver or to enable the use of a PC speaker or microphone. • This manual describes only the procedures for configuring
  • Kenwood TS-890S | Operation Manual - Page 164
    to a USB flash drive. The directory of the storage destination is "KENWOOD\TS-890\CAPTURE". • When removing the USB flash drive, make sure to execute "Safely analog meter to the METER terminal on the rear panel of this transceiver. A different output signal format can be configured for each of External
  • Kenwood TS-890S | Operation Manual - Page 165
    guidance or error tone emitted from this transceiver, the command response or error tone produced by this transceiver can also be heard at a remote location during, for example, KNS (KENWOOD NETWORK COMMAND SYSTEM) operation with this transceiver installed at a remote location. ● Audio output to
  • Kenwood TS-890S | Operation Manual - Page 166
    CTCSS frequency. Only RX signals with a matching CTCSS frequency are output from the ACC 2/USB port. Configuring the SQL Control Signal When operating this transceiver with an external device such as PC connected to the ACC 2 connector on the rear panel, the status of the SQL control signal for the
  • Kenwood TS-890S | Operation Manual - Page 167
    end in the standard settings. Before using the TS-590SG/ TS-590S as a sub-receiver, please read through the instruction manual and update documents. Configuration Using TS-890S at the TX/RX End 1 Enable this transceiver to function as a TX/RX end transceiver. Select "A (TX/RX)" in Menu [7-04] "Quick
  • Kenwood TS-890S | Operation Manual - Page 168
    " function to continue using it after changing to TS-890S. Follow the steps below to operate this transceiver. To combine the use of a transceiver other than this transceiver, please refer to the instruction manual of the model to be used. Using TS-890S at the Sub-receiver End (Master) 1 Turn ON
  • Kenwood TS-890S | Operation Manual - Page 169
    signals to the host transceiver while controlling the transceiver via PC using KNS (KENWOOD NETWORK COMMAND SYSTEM). is supported. ● DX packet cluster data cannot be sent out automatically to this transceiver. ● D710(A/E), TM-D710G(A/E) RC-D710 + TM-V71(A/E) TS-890S RC-D710 + PG-5J  9-pin D-SUB
  • Kenwood TS-890S | Operation Manual - Page 170
    12] "TX Inhibit While Busy" Setting Value Off (default)/ On Reversing the PKS Signal Polarity Short-circuiting the PKS terminal to GND places this transceiver in the TX mode. This polarity can be reversed according to the device to be connected. Configure in Advanced Menu [11] "PKS Polarity Reverse
  • Kenwood TS-890S | Operation Manual - Page 171
    configured on the menu screen. HF band, 50 MHz band and , please refer to the instruction manual of the linear amplifier to Connect to either ANT 1 or 2. TS-890S TS-890S 7-pin DIN Plug Linear Amplifier (Commercially Available some linear amplifiers that place this transceiver in the TX mode once
  • Kenwood TS-890S | Operation Manual - Page 172
    by the transmission system of this transceiver when there is a long time lag to the target band. Pressing F6 [BAND] each time toggles the selection to "HF Band", "50 MHz Band" and "70 MHz Band" (E type only) in when using a linear amplifier that supports full break-in. Configure "Keying Logic
  • Kenwood TS-890S | Operation Manual - Page 173
    connecting the exciter with a transverter, please refer to the instruction manual of the transverter in use. ● Some functions on this transceiver are not usable when a transverter is used. ● Turn off the power of both this transceiver and the transverter before connecting them. Check the connection
  • Kenwood TS-890S | Operation Manual - Page 174
    /OFF status of the antenna output function is stored separately for the HF band and 50/70 MHz band. Emergency Call (K Type Only) KENWOOD FM transceiver (K type) with a 6 pin mini DIN connector, you can set up the TS-890S transceiver and the FM transceiver as a crossband repeater. The FM transceiver
  • Kenwood TS-890S | Operation Manual - Page 175
    repeater frequency on the FM transceiver. 3 Select the same frequency for the terminal transceiver. 4 Select a HF/50 MHz frequency on the TS-890S transceiver. 5 Adjust the squelch threshold level so that both the TS-890S and FM transceivers mute. 6 On the TS-890S, press [MENU], then access Advanced
  • Kenwood TS-890S | Operation Manual - Page 176
    all the necessary cables to the TS-890S transceiver. 2 Select a frequency on the TS-890S transceiver. 3 On the TS-890S, press [MENU], then access Menu D710/G(A/E), TM-V71A + RC-D710, or TM-D700A transceiver. • Refer to the respective instruction manuals of the TH-D7A, TH-D72(A/E)/ TM-D710/G(A/E),
  • Kenwood TS-890S | Operation Manual - Page 177
    . Firmware Version Check Check the current firmware version before updating the firmware. Check in Advanced Menu [27] "Firmware Version" ● If a "firmware update failed" screen constantly appears while update is in progress, this could be due to system failure. Please contact KENWOOD service center
  • Kenwood TS-890S | Operation Manual - Page 178
    receiving WWVH (Hawaii), WWV (Colorado), BPM (Xi'an) or other types of standard radio wave. First of all, follow the steps below to set this transceiver to the mode for receiving the standard radio wave signals. The following is an example of the calibration procedure when the pitch frequency is 700
  • Kenwood TS-890S | Operation Manual - Page 179
    such as power outage, perform the adjustment again. The color tone of the display can be adjusted as follows. 1 Turn off the power of this transceiver. 2 Pressing and holding [CLR] while turning on the power displays the display color adjustment screen. 3 Use the controls below to adjust the color
  • Kenwood TS-890S | Operation Manual - Page 180
    the top case is removed, scratches may result when aligning it with the bottom case during the assembly. ● The 4 A fuse that comes supplied with this transceiver is to be used for the external antenna tuner. Do not use a fuse other than the one supplied. ● Be careful not to misplace the screw
  • Kenwood TS-890S | Operation Manual - Page 181
    accessory items unless you feel they are directly related to the service problem. Please do not send subassemblies or printed circuit boards. Send the complete transceiver. You may return your transceiver for service to the authorized KENWOOD dealer from whom you purchased it or any authorized
  • Kenwood TS-890S | Operation Manual - Page 182
    18 TROUBLESHOOTING Troubleshooting Check the following before requesting for repair of the transceiver. Problems Related to Reception and Transmission Symptom Probable Cause Corrective Action Power does not turn on when [ ] is The power switch of the regulated DC power
  • Kenwood TS-890S | Operation Manual - Page 183
    TROUBLESHOOTING VOX gain level Set the VOX function to OFF or adjust the VOX transceiver is not operated. is not properly adjusted. gain level. The signal is input from a connector for which Set Data VOX to OFF or review the audio the audio source setting of the TX audio is source setting
  • Kenwood TS-890S | Operation Manual - Page 184
    18 TROUBLESHOOTING Symptom Probable Cause Corrective Action The linear amplifier is not transceiver does not start up. The firmware of this transceiver cannot be detected. Rewrite the firmware. If the same symptom persists after rewriting the firmware, please send an inquiry to KENWOOD service
  • Kenwood TS-890S | Operation Manual - Page 185
    TROUBLESHOOTING 18 Problems Related to Data Communication, PC and Network Symptom . because the PC is connected to this transceiver before the driver is installed. The baud rates do not match each other. Check the baud rate of the TS-890S and ARCP-890. ① Flow control is not configured. ①
  • Kenwood TS-890S | Operation Manual - Page 186
    output and PTT output are the same as those configured in ① and ② respectively. When this transceiver is connected to When our transceiver (TH-D72/TS-590S/ a PC with a USB cable, the COM port TS-590SG/TS-990S/TS-890S/TH-D74) is number assigned to the PC becomes connected to a USB port that is
  • Kenwood TS-890S | Operation Manual - Page 187
    be recognized. The USB flash drive is not formatted by this transceiver. Format on this transceiver. Poor connection. Connect the USB flash drive. The USB flash drive is security-enabled. This transceiver does not support securityenabled USB flash drive. The USB flash drive is damaged. Check
  • Kenwood TS-890S | Operation Manual - Page 188
    18 TROUBLESHOOTING Troubles Related to Recording and Playback Symptom Probable Cause Corrective Action A message is displayed when [ ] is Timer recording is in progress. pressed during timer recording. To stop timer recording and allow this transceiver to be operated, press and hold F4 [(BREAK
  • Kenwood TS-890S | Operation Manual - Page 189
    with a new firmware using a transceiver with an old firmware. Follow the instructions in the error message. A failure in updating the firmware terminates the firmware updating process. (ERR: 0040) Refer to "Troubleshooting" in the instruction manual. Appears when some unknown problem has occurred
  • Kenwood TS-890S | Operation Manual - Page 190
    the error message number (ERR: 010A to 010F, 0110 to 0115) and send an inquiry to KENWOOD service center. A hardware error was detected. (ERR: 0117) Refer to "Troubleshooting" in the instruction manual. Perform Full Reset. If the same error message appears again after Full Reset, note down the
  • Kenwood TS-890S | Operation Manual - Page 191
    transmission and allow the temperature of this transceiver to go down. Very high temperature has been detected in the transceiver. Refer to "Troubleshooting" in the instruction manual (WR: 0106). Transmission capability is disabled until the transceiver cools down. Is the ambient temperature of
  • Kenwood TS-890S | Operation Manual - Page 192
    18 TROUBLESHOOTING Internal Beats Internal beats may occur within some of the amateur band frequencies. This is due to the frequency configuration of this transceiver and is not a malfunction. Example: 29.699 MHz, 51.957 MHz, 53.784 MHz, etc. Spurious Signals on the Bandscope Signals that are
  • Kenwood TS-890S | Operation Manual - Page 193
    890 Radio Host Program, ARVP-10 VoIP Program and ARUA-10 USB Audio Controller can be downloaded from the following website. http://www.kenwood.com/i/products/info/amateur/ software_download.html ● Optional accessories that can be used along with this transceiver by the guide on the back of the shield
  • Kenwood TS-890S | Operation Manual - Page 194
    No signal) Dimensions Without projections With projections Weight Output Power (AM) Modulation Maximum frequency Min 5 W) SSB: Balanced, AM: Low Power, FM: Reactance Wide: ±5 kHz or less, Narrow: ±2.5 kHz or less HF: -50 dB or less 50 MHz: -63 dB or less 70 MHz: -60 dB or less 60 dB or more 60
  • Kenwood TS-890S | Operation Manual - Page 195
    .0 to 70.5 MHz) 0.2 μV or less (28.0 to 30.0 MHz) 0.2 μV or less (50.0 to 54.0 MHz) 0.2 μV or less (70.0 to 70.5 MHz) 70 dB or more (HF), 60 dB or more (50/ 70 MHz) 70 dB or more 2.6 kHz or more (-6 dB), 4.4 kHz or less (-60 dB) 500 Hz or more (-6 dB
  • Kenwood TS-890S | Operation Manual - Page 196
    .. © 2019
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
TS-890S
INSTRUCTION MANUAL
B5A-2215-10 (K, E)