Kenwood TS-890S Operation Manual - Page 189
Error Messages
View all Kenwood TS-890S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 189 highlights
TROUBLESHOOTING 18 Error Messages The following error messages are displayed when an abnormality is detected on this transceiver. Follow the steps described for each error message to resolve the problem. ID 0012 0015 001B 001C 002F 0030 003B 003C 003E 003F 0040 0046 0047 0048 Message Description/Corrective Action Configurations for the Local Clock have not been completed. (ERR: 0012) Appears when attempting to launch the program timer while a local clock Associated functions cannot be used until the timer configurations is not configured. Configure the local clock in Clock menus [00] to [03]. have been completed. Connection to an NTP server has failed. (ERR: 0015) Appears when date/time data cannot be successfully acquired from the Ensure that the NTP server address and the network have been NTP server. correctly configured. Follow the instructions in the error message. A file is invalid. (ERR: 001B) Appears when a file error is detected while reading a file that contains the RX equalizer, TX equalizer and settings data. An error occurred while a file was being read from a USB flash drive. (ERR: 001C) Appears when a file error is detected while reading a file stored in the USB flash drive that contains the RX equalizer, TX equalizer and settings data. A USB flash drive cannot be detected. (ERR: 002F) Failure to detect the USB flash drive may be caused by the following. • The USB flash drive is not correctly connected to a USB connector. • The USB flash drive is not in the specified format. The USB flash drive must be formatted in the "USB/File Management" screen. Appears when some unknown problem has occurred on the USB flash drive. Follow the instructions in the error message. An error occurred while a file is being written to an internal memory Appears when the file name is duplicated or an unexpected error has area or a USB flash drive. (ERR: 0030) occurred. Follow the instructions in the error message. Failure in Deleting of a File. (ERR: 003B) Appears when the deletion of file failed. Make sure the USB flash drive is not write-protected. Safe Removal of USB Flash Drive was failed. (ERR: 003C) The data file may not be stored onto the USB flash drive. Turn OFF the DC power supply, and then disconnect the USB flash drive. Appears when some problem has occurred while unmounting the USB flash drive. Follow the instructions in the error message. A failure in detecting the firmware file will terminate the firmware updating process. (ERR: 003E) The termination of the firmware update may be caused by the following: • The firmware file is not stored in the specified folder. • The USB flash drive is not in the specified format. • The USB flash drive must be formatted in the "USB/File Management" screen. • The newer version firmware has already been applied to the transceiver. • The firmware file is not legitimate. Restart the transceiver and then execute the firmware update again from the beginning. Appears when some unknown problem has occurred while reading the firmware file. Follow the instructions in the error message. The selected file cannot be read by this transceiver with the earlier version firmware installed. (ERR: 003F) Update the transceiver firmware using the latest version of the firmware. Appears when attempting to read a settings file written by a transceiver installed with a new firmware using a transceiver with an old firmware. Follow the instructions in the error message. A failure in updating the firmware terminates the firmware updating process. (ERR: 0040) Refer to "Troubleshooting" in the instruction manual. Appears when some unknown problem has occurred while rewriting the firmware file. The storage location cannot be changed while an audio recording. Appears when attempting to change the destination for saving the file (ERR: 0046) while manual recording is in progress. The storage location cannot be changed while a CW QSO log Appears when attempting to change the destination for saving the file recording. (ERR: 0047) while CW communication log recording is in progress. The storage location cannot be changed while a RTTY QSO log Appears when attempting to change the destination for saving the file recording. (ERR: 0048) while RTTY communication log recording is in progress. 18-9