Kenwood TS-890S Operation Manual - Page 191

Warning Messages

Get Kenwood TS-890S PDF manuals and user guides View all Kenwood TS-890S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 191 highlights

TROUBLESHOOTING 18 Warning Messages The following warning messages are displayed in the event of an erroneous operation or when a problem on this transceiver is detected. Follow the steps described for each warning message to resolve the problem. If "Troubleshooting" is indicated in the warning message or when the problem cannot be resolved, please refer to the list of error messages and "Troubleshooting" (18-2). ID 000C 0031 0032 0033 0034 0039 0043 004A 0053 0101 0102 0104 0106 Message Description/Corrective Action This audio file cannot be reproduced. (WR: 000C) Appears when the format of the wav file is not supported by this transceiver. Check the file format on a PC to see if the file is in the wav format that can be played on this transceiver. Due to insufficient memory of the data storage or the write protection of the USB flash drive, the data storing process was terminated. (WR: 0031) Ensure that there is sufficient memory and that data storage has been enabled. Appears when the maximum number of files in each folder has been exceeded, insufficient memory space or writing forbidden is detected when writing a file. Selects the days of the week. (WR: 0032) Appears when [OK] is pressed with all the days of the week unchecked on the program timer configuration screen. A maximum of 4 hours of recording time can be configured. (WR: 0033) Ensure that the Power-on Time and Power-off time are appropriate. Appears when [OK] is pressed with the time limit exceeded when configuring the Power-on Time and Power-off Time on the program timer configuration screen. The same clock time cannot be configured for both the Power-on Time and Power-off Time. (WR: 0034) Appears when [OK] is pressed with an invalid time range configured for Ensure that the Power-on Time and Power-off Time are this transceiver on the program timer configuration screen. appropriate. Failure in formatting of a USB flash drive has been detected. (WR: 0039) The failure may be caused by one or more of the following: • The write protected USB flash drive is connected to a USB connector. • The USB flash drive is not correctly connected to a USB Appears when formatting of the USB flash drive failed. Follow the instructions in the message. connector. • The security-protected USB flash drive is connected to a USB connector. The file cannot be accessed while recording data. (WR: 0043) Appears when attempting to read a log file for which recording is currently in progress. Select copy item. (WR: 004A) Appears when attempting to copy files to a PC with all the files unchecked on the screen for selecting the files to copy. Select delete item. (WR: 0053) Appears when attempting to delete files while all the files are unchecked on the screen for selecting the files to delete. The Programmable Timer is about to start recording the received audio. (WR: 0101) The recording can begin if the transceiver has been turned OFF. If the USB flash drive has selected as the file storage location, connect a USB flash drive to the USB connector before recording Appears when the power of this transceiver is turned on approximately 3 minutes and 1 minute before timer recording starts. Follow the instructions in the message. starts. Recording by the Programmable Timer.(WR: 0102) To stop recording, press and hold [(BREAK)] (F). Appears when [ ] is pressed and held down during timer recording while the screen is turned off. High temperature has been detected in the transmitter. Refer to "Troubleshooting" in the instruction manual (WR: 0104). To prevent the transmitter from being damaged, the transmit power has been reduced to 5 W. Stop the transmission and allow the temperature of this transceiver to go down. Very high temperature has been detected in the transceiver. Refer to "Troubleshooting" in the instruction manual (WR: 0106). Transmission capability is disabled until the transceiver cools down. Is the ambient temperature of this transceiver high (such as when the transceiver is exposed to direct sunlight)? Please operate it in a wellventilated place. 18-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
Warning Messages
The following warning messages are displayed in the event of an erroneous operation or when a problem on this transceiver is detected.
Follow the steps described for each warning message to resolve the problem. If “Troubleshooting” is indicated in the warning message
or when the problem cannot be resolved, please refer to the list of error messages and “
Troubleshooting
” (
18-2
).
ID
Message
Description/Corrective Action
000C
This audio file cannot be reproduced. (WR: 000C)
Appears when the format of the wav file is not supported by this
transceiver.
Check the file format on a PC to see if the file is in the wav format that
can be played on this transceiver.
0031
Due to insufficient memory of the data storage or the write
protection of the USB flash drive, the data storing process was
terminated. (WR: 0031)
Ensure that there is sufficient memory and that data storage has
been enabled.
Appears when the maximum number of files in each folder has been
exceeded, insufficient memory space or writing forbidden is detected
when writing a file.
0032
Selects the days of the week. (WR: 0032)
Appears when [OK] is pressed with all the days of the week unchecked
on the program timer configuration screen.
0033
A maximum of 4 hours of recording time can be configured. (WR:
0033)
Ensure that the Power-on Time and Power-off time are
appropriate.
Appears when [OK] is pressed with the time limit exceeded when
configuring the Power-on Time and Power-off Time on the program timer
configuration screen.
0034
The same clock time cannot be configured for both the Power-on
Time and Power-off Time. (WR: 0034)
Ensure that the Power-on Time and Power-off Time are
appropriate.
Appears when [OK] is pressed with an invalid time range configured for
this transceiver on the program timer configuration screen.
0039
Failure in formatting of a USB flash drive has been detected. (WR:
0039)
The failure may be caused by one or more of the following:
•
The write protected USB flash drive is connected to a USB
connector.
•
The USB flash drive is not correctly connected to a USB
connector.
•
The security-protected USB flash drive is connected to a USB
connector.
Appears when formatting of the USB flash drive failed.
Follow the instructions in the message.
0043
The file cannot be accessed while recording data. (WR: 0043)
Appears when attempting to read a log file for which recording is
currently in progress.
004A
Select copy item. (WR: 004A)
Appears when attempting to copy files to a PC with all the files
unchecked on the screen for selecting the files to copy.
0053
Select delete item. (WR: 0053)
Appears when attempting to delete files while all the files are unchecked
on the screen for selecting the files to delete.
0101
The Programmable Timer is about to start recording the received
audio. (WR: 0101)
The recording can begin if the transceiver has been turned OFF.
If the USB flash drive has selected as the file storage location,
connect a USB flash drive to the USB connector before recording
starts.
Appears when the power of this transceiver is turned on approximately
3 minutes and 1 minute before timer recording starts. Follow the
instructions in the message.
0102
Recording by the Programmable Timer.(WR: 0102)
To stop recording, press and hold [(BREAK)] (F).
Appears when [
] is pressed and held down during timer recording
while the screen is turned off.
0104
High temperature has been detected in the transmitter. Refer to
"Troubleshooting" in the instruction manual (WR: 0104).
To prevent the transmitter from being damaged, the transmit
power has been reduced to 5 W.
Stop the transmission and allow the temperature of this transceiver to
go down.
0106
Very high temperature has been detected in the transceiver. Refer
to "Troubleshooting" in the instruction manual (WR: 0106).
Transmission capability is disabled until the transceiver cools
down.
Is the ambient temperature of this transceiver high (such as when the
transceiver is exposed to direct sunlight)? Please operate it in a well-
ventilated place.
TROUBLESHOOTING
18
18-11