Kenwood VR-5700 User Manual 1 - Page 35

To Connect a PCM Digital Output Laser Disc player, Disc Player

Get Kenwood VR-5700 PDF manuals and user guides View all Kenwood VR-5700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Connections Chapter One : Connecting Your Devices Connecting Your Laser Disc Player (without AC-3 RF Output), continued Do not plug in the receiver to AC power until you have connected all your devices. These instructions describe how to connect a laser disc player with a PCM Digital Output. If your player has a Dolby Digital (AC-3) RF Out, see "Connecting Your Laser Disc Player (with AC-3 RF Output)" on page 26. This configuration does not allow Dolby Digital laser discs to be played. Please refer to your laser disc player's instructions for more detail about its connection jacks and capabilities. The instructions in this section show one of several possible variations on connecting your laser disc player. For further assistance on optional configurations, contact the store where you purchased your receiver. To Connect a PCM Digital Output Laser Disc Player: 1. Review the information under "Before You Begin" on page 1. It contains important notes about the types of video connections you can make. 2. Connect the audio cables from the laser disc player's Audio OUT jacks to the receiver's AUDIO jacks (VIDEO3 PLAY IN)as shown to the left. 3. Connect the video cable from the laser disc player's Video OUT jack to the receiver's VIDEO PLAY IN jack as shown to the left. Note that the jack sets are linked, even though they are not adjacent. You must connect all of the cables from your laser disc player to a linked jack set. If you connect the analog cables to VIDEO2 and the digital cable to VIDEO3, your receiver will not work correctly. 4. Connect the digital cable (either optical or coaxial) from the laser disc player's digital jack to the appropriate digital jack on the receiver as shown to the left. Your laser disc player supports only one of the digital connection methods-do not connect both. (The optical digital input jacks are available only on the VR-5700/VR-5090) 5. Go to "Noting Your Devices" on page 3 and note which jacks you used to connect your laser disc player. In addition, note the brand name and model number of the laser disc player. When play DTS-encoded software in multichannel con- figuration, the connected audio signal should be the digi- tal signal. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
29
Chapter One : Connecting Your Devices
Connections
Connecting Your Laser Disc Player (without AC-3 RF Output), continued
Do not
plug in the receiver to AC power until you have
connected all your devices.
These instructions describe how to connect a laser disc player
with a PCM Digital Output. If your player has a Dolby Digi-
tal (AC-3) RF Out, see
“
Connecting Your Laser Disc Player
(with AC-3 RF Output)
”
on page 26. This configuration does
not allow Dolby Digital laser discs to be played. Please re-
fer to your laser disc player
’
s instructions for more detail
about its connection jacks and capabilities.
The instructions in this section show one of several pos-
sible variations on connecting your laser disc player. For
further assistance on optional configurations, contact the
store where you purchased your receiver.
To Connect a PCM Digital Output Laser
Disc Player:
1.
Review the information under
“
Before You Begin
”
on
page 1. It contains important notes about the types of
video connections you can make.
2.
Connect the audio cables from the laser disc player
’
s
Audio OUT jacks to the receiver
’
s
AUDIO
jacks (
VIDEO3
PLAY IN
)as shown to the left.
3.
Connect the video cable from the laser disc player
’
s
Video OUT jack to the receiver
’
s
VIDEO PLAY IN
jack
as shown to the left.
Note that the jack sets are linked, even though they are
not adjacent. You
must
connect all of the cables from
your laser disc player to a linked jack set. If
you connect
the analog cables to
VIDEO2
and the digital cable to
VIDEO3
, your receiver will not work correctly.
4.
Connect the digital cable (either optical or coaxial) from
the laser disc player
’
s digital jack to the appropriate digi-
tal jack on the receiver as shown to the left. Your laser
disc player supports only one of the digital connection
methods
—
do not
connect both. (The optical digital
input jacks are available only on the VR-5700/VR-5090)
5.
Go to
“
Noting Your Devices
”
on page 3 and note which
jacks you used to connect your laser disc player. In ad-
dition, note the brand name and model number of the
laser disc player.
When play DTS-encoded software in multichannel con-
figuration, the connected audio signal should be the digi-
tal signal.