Kenwood VRS-7200 Instruction Manual - Page 36

Convenient functions You can make further adjustments to the sound while listening to playback in the surround mode. ÷ The mode using the SOUND key is defeated when the REC MODE is ON. § DIMMER ° SLEEP ENTER SOUND LISTEN MODE % / fi RCV MODE INPUT SELECTOR Adjusting the sound MULTI CONTROL ENTER 1 Press the RCV MODE key on the remote control unit to set it to the receiver control mode. 2 Press the SOUND key. 3 Press the MULTI CONTROL @ / # (or the @ / # keys) to select the setting item and press the ENTER. Note that some items are not displayed in certain modes. 1 "SP LEVEL": *1 Adjusting the volume level of each channel 2 "INPUT": (Analog mode only) ™ Input level adjustment 3 "TONE": *2 ¢ Tone level adjustment 4 "EFFECT": (DSP mode only) DSP effect level adjustment 5 "DUAL MONO": *3 ‡ Selection between Stereo, Main audio, Sub audio and Main + Sub audio 6 "MIDNIGHT": *4 ° Midnight mode adjustment 7 "PANORAMA": *5 ‡ Panorama mode ON/OFF 8 "DIMENSION": *5 ‡ Dimension adjustment 9 "C WIDTH": *5 ‡ Center width adjustment 0 "C IMAGE": *6 ° Center image mode adjustment *1 The setting in the SOUND mode is temporary. It returns automati- cally to the original level set in "Speaker settings" when the receiver is turned OFF/ON. * *2 PCM stereo and analog stereo mode only. *3 DOLBY DIGITAL mode only *4 DOLBY DIGITAL, DTS mode only *5 Only when the input signal is a 2-channel signal in the DOLBY PRO LOGIC IIx MUSIC or DOLBY PRO LOGIC II MUSIC mode. *6 Only when the input signal is a 2-channel signal in the DTS NEO:6 MUSIC mode. 4 Use the MULTI CONTROL % / fi (or the % / fi keys) to adjust the setting as desired. ÷ The adjustment item is displayed for approximately 20 seconds. 5 Press the SOUND key again to return to the input indication. Adjusting the volume level of each channel The volume levels of the center speaker, subwoofer, surround speaker and surround back speaker channels can be adjusted during playback. 1 Press the RCV MODE key on the remote control unit to set it to the receiver control mode. 2 Press the SOUND key. 3 Use the MULTI CONTROL @ / # (or the @ / # keys) to select "SP LEVEL" on setup displays, and press the ENTER. 4 Use the MULTI CONTROL @ / # (or the @ / # keys) to select the speaker. 1 Subwoofer level adjustment ("SW" indicator blinks) 2 Center speaker level adjustment ("C" indicator blinks) 3 Surround speaker level adjustment ("LS", "RS" indicator blinks) 4 Surround back speaker level adjustment ("LB", "RB" or "BS" indicator blinks) 5 Use the MULTI CONTROL % / fi (or the % / fi keys) to adjust the speaker volume level. ÷ The level of each speaker channel can be adjusted in 1 dB steps between -10 dB and +10 dB. 6 Repeat steps 4 and 5 as required. 7 Press the SOUND key again to return to the input indication. ÷ The setting in the SOUND mode is temporary. It returns automati- cally to the original level set in "Speaker settings" when the receiver is turned OFF/ON. * Adjusting the DSP effect level (DSP mode only) The DSP effect level can be adjusted when the listen mode is a DSP surround mode "ARENA", "JAZZ CLUB", "THEATER", "STADIUM" or "DISCO". 1 Press the RCV MODE key on the remote control unit to set it to the receiver control mode. 2 Press the SOUND key. 3 Use the MULTI CONTROL @ / # (or the @ / # keys) to select "EFFECT" on setup displays, and press the ENTER. 4 Use the MULTI CONTROL % / fi (or the % / fi keys) to adjust the EFFECT LEVEL. ÷ The DSP effect level can be adjusted in the range between 1 and 5. 5 Press the SOUND key again to return to the input indication. 36 EN