KitchenAid KBSD702MPS Owners Manual - Page 18

INSTALLATION INSTRUCTIONS, Unpack the Refrigerator

Get KitchenAid KBSD702MPS PDF manuals and user guides View all KitchenAid KBSD702MPS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Side Trim 11/16" (18.0 mm) 1/2" (12.2 mm) INSTALLATION INSTRUCTIONS Unpack the Refrigerator WARNING 9/16" (13.9 mm) 5/8" (15.7 mm) Inset Installation Dimensions 1. Measure the distance from point A (as shown) to the back wall. Add 1/16" (1.6 mm) to this measurement to allow the side panel to fit into the trim. 2. If the panel is more than 11/32" (8.7 mm) thick, route the front edge to allow the side panel to fit into the trim. A Recessed Inset Installation Dimensions 1. Measure the distance from point A (as shown) to back wall. 2. Route the front edge of the support board or attach a 3/8" (9.5 mm) board to hold the panel in the cabinet side trim. Tip Over Hazard Refrigerator is top heavy and tips easily when not completely installed. Keep doors taped closed until refrigerator is completely installed. Use two or more people to move and install refrigerator. Failure to do so can result in death or serious injury. IMPORTANT: � Do not remove the film covering until the refrigerator is in its operating location. � All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator. � Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating location. 1. Remove and save the literature package bag taped to the side of the refrigerator and the parts bag behind the grille. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator bottom. NOTE Do not remove tape and door bracing until the refrigerator is in its final location. 2. If necessary, reduce the tipping radius. See "Tipping Radius" for ceiling height requirements or "Reduce Tipping Radius" for step-by-step instructions. If you do not need to reduce the tipping radius, proceed to "Move the Refrigerator into House." Reduce Tipping Radius (If Required) Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See "Tipping Radius" in the "Installation Requirements" section for more information. If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart). Model 36 42 48 Reduced Tipping Radius 89" (225.9 cm) 901/2" (229.9 cm) 911/4" (231.8 cm) A 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
18
Side Trim
Inset Installation Dimensions
1.
Measure the distance from point A (as shown) to the back
wall. Add 1/16" (1.6 mm) to this measurement to allow the
side panel to fit into the trim.
2.
If the panel is more than 11/32" (8.7 mm) thick, route the front
edge to allow the side panel to fit into the trim.
Recessed Inset Installation Dimensions
1.
Measure the distance from point A (as shown) to back wall.
2.
Route the front edge of the support board or attach a
3/8" (9.5 mm) board to hold the panel in the cabinet side trim.
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
IMPORTANT:
�
Do not remove the film covering until the refrigerator is in its
operating location.
�
All four leveling legs must contact the floor to support and
stabilize the full weight of the refrigerator.
�
Keep the cardboard shipping piece or plywood under the
refrigerator until it is installed in the operating location.
1.
Remove and save the literature package bag taped to the side
of the refrigerator and the parts bag behind the grille. Remove
the four brackets (two on each side) that attach the shipping
base to the refrigerator bottom.
NOTE
Do not remove tape and door bracing until the refrigerator is in
its final location.
2.
If necessary, reduce the tipping radius. See "Tipping Radius"
for ceiling height requirements or "Reduce Tipping Radius" for
step-by-step instructions. If you do not need to reduce the
tipping radius, proceed to "Move the Refrigerator into House."
Reduce Tipping Radius (If Required)
Before bringing the refrigerator into the home, be sure there is
adequate ceiling height to stand the refrigerator upright. See
"Tipping Radius" in the "Installation Requirements" section for
more information.
If you do not have adequate ceiling height to stand the refrigerator
upright, the tipping radius can be reduced by removing the top
grille and side trims (see the following chart).
Model
Reduced Tipping Radius
36
89" (225.9 cm)
42
90
1
/
2
" (229.9 cm)
48
91
1
/
4
" (231.8 cm)
(18.0 mm)
11
/
16
"
(12.2 mm)
1
/
2
"
(13.9 mm)
9
/
16
"
(15.7 mm)
5
/
8
"
A
A
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is completely
installed.
Use two or more people to move and install refrigerator.
Failure to do so can result in death or serious injury.