Konica Minolta bizhub 20P bizhub 20P Network User Guide - Page 72

Using ARP to con the IP address, Windows, systems

Get Konica Minolta bizhub 20P PDF manuals and user guides View all Konica Minolta bizhub 20P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Appendix Using ARP to configure the IP address 0 If you are unable to use the BRAdmin Light and your network does not use a DHCP server, you can also use the ARP command. The ARP command is available on Windows® systems that have TCP/IP installed as well as UNIX systems. To use arp enter the following command at the command prompt: arp -s ipaddress ethernetaddress Where ethernetaddress is the MAC Address (Ethernet Address) of the print server and ipaddress is the IP address of the print server. For example: „ Windows® systems Windows® systems require the dash "-" character between each digit of the MAC Address (Ethernet Address). arp -s 192.168.1.2 00-80-77-31-01-07 Note You must be on the same Ethernet segment (that is, there cannot be a router between the print server and operating system) to use the arp -s command. If there is a router, you may use BOOTP or other methods described in this chapter to enter the IP address. If your Administrator has configured the system to deliver IP addresses using BOOTP, DHCP or RARP your KONICA MINOLTA print server can receive an IP address from any one of these IP address allocation systems. In which case, you will not need to use the ARP command. The ARP command only works once. For security reasons, once you have successfully configured the IP address of a KONICA MINOLTA print A server using the ARP command, you cannot use the ARP command again to change the address. The print server will ignore any attempts to do this. If you wish to change the IP address again, use Web Based Management (web browser), TELNET (using the SET IP ADDRESS command) or factory reset the print server (which will then allow you to use the ARP command again). To configure the print server and to verify the connection, enter the following command ping ipaddress where ipaddress is the IP address of the print server. For example, ping 192.189.207.2. 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
Appendix
66
A
Using ARP to configure the IP address
0
If you are unable to use the BRAdmin Light and your network does not use a DHCP server, you can also use
the ARP command. The ARP command is available on Windows
®
systems that have TCP/IP installed as well
as UNIX systems. To use arp enter the following command at the command prompt:
arp -s ipaddress ethernetaddress
Where
ethernetaddress
is the MAC Address (Ethernet Address) of the print server and
ipaddress
is
the IP address of the print server. For example:
Windows
®
systems
Windows
®
systems require the dash “-” character between each digit of the MAC Address (Ethernet
Address).
arp -s 192.168.1.2 00-80-77-31-01-07
Note
You must be on the same Ethernet segment (that is, there cannot be a router between the print server and
operating system) to use the arp -s command.
If there is a router, you may use BOOTP or other methods described in this chapter to enter the IP address.
If your Administrator has configured the system to deliver IP addresses using BOOTP, DHCP or RARP your
KONICA MINOLTA print server can receive an IP address from any one of these IP address allocation
systems. In which case, you will not need to use the ARP command. The ARP command only works once.
For security reasons, once you have successfully configured the IP address of a KONICA MINOLTA print
server using the ARP command, you cannot use the ARP command again to change the address. The print
server will ignore any attempts to do this. If you wish to change the IP address again, use Web Based
Management (web browser), TELNET (using the SET IP ADDRESS command) or factory reset the print
server (which will then allow you to use the ARP command again).
To configure the print server and to verify the connection, enter the following command
ping ipaddress
where
ipaddress
is the IP address of the print server. For example,
ping 192.189.207.2
.