Home » Kyocera Manuals » Printers » Kyocera TASKalfa 2420w » Manual Viewer

Kyocera TASKalfa 2420w TASKalfa 2420w Operation Guide - Page 35

Cut Sheet Media

View all Kyocera TASKalfa 2420w manuals

Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2. 6 Cut Sheet Media There are several size markings on the table of Bypass Feeder which indicate possible feed positions. Place the cut sheet on the table between its concerning size markings then insert it into the Bypass Feeder. When the leading edge touches the feeding roller, the printer automatically carries and sets the paper at the proper position. size marking NOTE (1) As a curly cut sheet will cause a mis-feed, straighten the sheet as far as possible before printing. And set the sheet in "curl down" direction as a mis-feed can be avoided. "Curl up" sheets tend to result in a mis-feed. Correct: curl down Wrong: curl up (2) Setting a cut sheet to the Bypass Feeder while the printer is processing a print job cause a paper jam. 2-14 Chapter 2 Basic Operation

Section	Page
2420 / 9124 / 8124 Hardware Operation Guide	1
Safety Warnings	3
WARNING	4
CAUTION	5
Chapter 1 Before Use	6
1. 1 Installation Requirements	7
1. 2 Originals Prohibited from Duplication	8
1. 3 Features	9
1. 4 Specifications	10
1. 4. 1 General	10
1. 4. 2 Printer part	11
1. 4. 3 Scanner part	13
1. 5 Appearance	14
1. 5. 1 Front view	14
1. 5. 2 Rear view	15
1. 6 Specifications for the Scan Original	16
1. 7 Specifications for the Printing Paper	19
1. 7. 1 Papers not available to use	19
1. 7. 2 Keeping the paper in the custody	20
1. 7. 3 Treatment against environmental condition	21
Chapter 2 Basic Operation	22
2. 1 Turning on	23
2. 2 Turning off	25
2. 3 Replacing Roll Media	26
2. 4 Initial Cut	30
2. 5 Toner Supply	31
2. 6 Cut Sheet Media	35
2. 7 Copying	36
2. 8 Emergency Stop of Scan or Copy	37
2. 9 Canceling Sleep Mode	38
Chapter 3 Error Correction	39
3. 1 Mis-feed Error	40
3. 1. 1 J-0103 Roll Deck section	41
3. 1. 2 J-0203 Manual Feeder section	43
3. 1. 3 J-0104 / 0204 Media Feeder section 1	44
3. 1. 4 J-0105 / 0205 Media Feeder section 2	46
3. 1. 5 J-0106 / 0206 Fuser section	48
3. 1. 6 J-1300 / 1400 Door Open while printing	51
3. 1. 7 Original Jam	54
3. 2 Other Operator Call Error	55
3. 2. 1 Roll Replacement	55
3. 2. 2 Toner Empty	55
3. 2. 3 Scanner Unit Open	55
3. 2. 4 Printer Not Available	55
3. 3 Service Call Error	56
Chapter 4 Maintenance	57
4. 1 Cleaning	58
4. 1. 1 Scanner Unit	58

Match case Limit results 1 per page

Chapter 2

Basic Operation

2-14

2. 6

Cut Sheet Media

There are several size markings on the table of Bypass Feeder which indicate possible feed

positions.

Place the cut sheet on the table between its concerning size markings then insert it into the Bypass

Feeder. When the leading edge touches the feeding roller, the printer automatically carries and

sets the paper at the proper position.

NOTE

(1) As a curly cut sheet will cause a mis-feed, straighten the sheet as far as possible before

printing. And set the sheet in “curl down” direction as a mis-feed can be avoided. “Curl up”

sheets tend to result in a mis-feed.

Correct:

curl down

Wrong:

curl up

(2) Setting a cut sheet to the Bypass Feeder while the printer is processing a print job cause a

paper jam.

size marking