LG A939KBGS Owners Manual - Page 52

Anti-tip Kit Installation, mounting band directly behind the product.

Get LG A939KBGS PDF manuals and user guides View all LG A939KBGS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

12 INSTALLATION 5 Plug the power plug into the outlet. • When the power plug is connected correctly, the status display flashes, and the product setting is initialized. Once initialization is completed, the status display turns off. • Use a velcro tie to bind and tidy the excess cable.  DN Anti-tip Kit Installation The anti-tip kit is designed to secure the product to the wall in order to prevent it from tipping over and causing personal injury or damage to itself or the floor. WARNING • Carefully read and follow the guidelines in order to prevent property damage or personal injury. • Do not lean against the product or place a heavy object on top of it. • Manage and supervise children or pets to prevent them from knocking into or climbing on the product. • If you prefer not to install this kit immediately, ensure that you keep it out of the reach of children. • Do not use this kit for purposes other than the installation of the charging station. • Wear gloves and protective clothing in order to prevent personal injury. • When drilling a hole in concrete, take caution and wear protective goggles. • Before drilling into a wall, make sure that there are no vents, gas or water pipes, or electrical cables behind the wall. 1 Before moving the product to its final position, mark the location on the wall where you will attach the anti-tip cord. If you are not drilling into a wall stud, you will need to use the wall mounting anchor. • Install the wall mounting anchor and the mounting band directly behind the product. 2 Attach one of the mounting bands to the loop at one end of the cord. 3 If drilling into drywall, use a 4 mm bit to drill a hole 1 3/4" (44.5 mm) deep at the marked location and insert the wall mounting anchor first. Then screw the mounting band into the anchor with the wall mounting screw. When screwing into a wall stud or concrete, use the wall mounting screw without the anchor. 4 Thread the other end of the cord through the slide as shown to form a loop. Attach the second mounting band to this loop. 5 Use the product mounting screw to attach the mounting band to the back of the product. 6 Place the product in its final location and use the slider to adjust the length of the cord until there is about 1 inch of play in the cord.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
12
INSTALLATION
5
Plug the power plug into the outlet.
•
When the power plug is connected
correctly, the status display flashes, and the
product setting is initialized. Once
initialization is completed, the status display
turns off.
•
Use a velcro tie to bind and tidy the excess
cable.
Anti-tip Kit Installation
The anti-tip kit is designed to secure the product to
the wall in order to prevent it from tipping over
and causing personal injury or damage to itself or
the floor.
WARNING
•
Carefully read and follow the guidelines in order
to prevent property damage or personal injury.
•
Do not lean against the product or place a heavy
object on top of it.
•
Manage and supervise children or pets to
prevent them from knocking into or climbing on
the product.
•
If you prefer not to install this kit immediately,
ensure that you keep it out of the reach of
children.
•
Do not use this kit for purposes other than the
installation of the charging station.
•
Wear gloves and protective clothing in order to
prevent personal injury.
•
When drilling a hole in concrete, take caution
and wear protective goggles.
•
Before drilling into a wall, make sure that there
are no vents, gas or water pipes, or electrical
cables behind the wall.
1
Before moving the product to its final
position, mark the location on the wall where
you will attach the anti-tip cord. If you are not
drilling into a wall stud, you will need to use
the wall mounting anchor.
•
Install the wall mounting anchor and the
mounting band directly behind the product.
2
Attach one of the mounting bands to the loop
at one end of the cord.
3
If drilling into drywall, use a 4 mm bit to drill a
hole 1 3/4" (44.5 mm) deep at the marked
location and insert the wall mounting anchor
first. Then screw the mounting band into the
anchor with the wall mounting screw. When
screwing into a wall stud or concrete, use the
wall mounting screw without the anchor.
4
Thread the other end of the cord through the
slide as shown to form a loop. Attach the
second mounting band to this loop.
5
Use the product mounting screw to attach the
mounting band to the back of the product.
6
Place the product in its final location and use
the slider to adjust the length of the cord until
there is about 1 inch of play in the cord.
2"(5 cm)