LG DLEX7800WE Owners Manual - Page 25
Connecting Gas Dryers
View all LG DLEX7800WE manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 25 highlights
24 INSTALLATION Connecting Gas Dryers Warning To reduce the risk of fire or explosion, electric shock, property damage, injury to persons, or death when using this appliance, follow basic safety precautions. Gas Supply Requirements •• As shipped from the factory, this dryer is configured for use with natural gas (NG). It can be converted for use with propane (LP) gas. Gas pressure must not exceed 8-inch (20.3 cm) water column for NG, or 13-inch (33 cm) water column for LP. •• A qualified service or gas company technician must connect the dryer to the gas service. Failure to follow these instructions may result in fire, explosion, or death. •• Isolate the dryer from the gas supply system by closing its individual manual shutoff valve during any pressure testing of the gas supply. Failure to do so may result in fire, explosion, or death. •• Supply line requirements: Your laundry room must have a rigid gas supply line to your dryer. In the United States, an individual manual shutoff valve MUST be installed within at least 6 ft. (1.8 m) of the dryer, in accordance with the National Fuel Gas Code ANSI Z223.1 or Canadian gas installation code CSA B149.1. A 1/8-inch (0.3 cm) NPT pipe plug must be installed. Failure to do so may result in fire, explosion, or death. •• If using a rigid pipe, the rigid pipe should be ½ inch IPS. If acceptable under local codes and ordinances and when acceptable to your gas supplier, 3/8-inch (1 cm) approved tubing may be used where lengths are less than 20 ft. (6.1 m). Larger tubing should be used for lengths in excess of 20 ft. (6.1 m). Failure to do so may result in fire, explosion, or death. •• Connect the dryer to the type of gas shown on the nameplate. Failure to do so may result in fire, explosion, or death. •• To prevent contamination of the gas valve, purge the gas supply of air and sediment before connecting the gas supply to the dryer. Before tightening the connection between the gas supply and the dryer, purge remaining air until the odor of gas is detected. Failure to do so may result in fire, explosion, or death. •• DO NOT use an open flame to inspect for gas leaks. Use a noncorrosive leak detection fluid. Failure to do so may result in fire, explosion, or death. •• Use only a new AGA- or CSA-certified gas supply line with flexible stainless steel connectors. Failure to do so may result in fire, explosion, or death. •• Securely tighten all gas connections. Failure to do so may result in fire, explosion, or death. •• Use Teflon tape or a pipe-joint compound that is insoluble in propane (LP) gas on all pipe threads. Failure to do so may result in fire, explosion, or death. •• DO NOT attempt any disassembly of the dryer; disassembly requires the attention and tools of an authorized and qualified service technician or company. Failure to follow this warning may result in fire, explosion, or death. Electrical Requirements for Gas Models Only •• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Failure to follow this warning may result in fire, explosion, or death. •• For personal safety, this dryer must be properly grounded. Failure to follow this warning may result in fire, explosion, or death. •• This dryer must be plugged into a 120-VAC, 60Hz. grounded outlet protected by a 15-ampere fuse or circuit breaker. Failure to follow this warning may result in fire, explosion, or death. •• Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Failure to follow this warning may result in fire, explosion, or death. PPlluuggdrdyerryientroianto a 120 VAC, 60 Hz grounded 3-prong outlet. Warning ELECTRIC SHOCK HAZARD Failure to follow safety warnings could result in serious injury or death. This dryer is equipped with a three-prong grounding plug for protePlcugtion against shock haCoznanercdtioannd should be pGlausgSugpepldy directly into a propAeGrAly/CSgAr-oCeur nded threeSh-uptroVnaglvereceptacle. Do not cut oSCrtoanrinneleemcstsooSrtveeel Ftlehxeiblegrounding prong from this plug. MFL70442605_en_190215.indd 24 2019-02-15 오후 2:38:21