LG HECTO Additional Link - Installation Manual

LG HECTO Manual

Get LG HECTO PDF manuals and user guides View all LG HECTO manuals
Add to My Manuals
Save this manual to your list of manuals

LG HECTO manual content summary:

  • LG HECTO | Additional Link - Installation Manual - Page 1
    Owner's Manual Laser Display install guide Please read the safety information carefully before using the product. P/NO : MFL67652408(1302-REV00) www.lg.com
  • LG HECTO | Additional Link - Installation Manual - Page 2
    injury. yyThe product should be installed where its weight can be supported. - Otherwise, the product may fall and cause personal product. - The product may fall and cause injury. CAUTION yyFollow the instructions in the manual to install the product. - Otherwise, it may cause serious injury or
  • LG HECTO | Additional Link - Installation Manual - Page 3
    the holes in the wall, make sure you use a drill and a drill bit with the specified size of diameter. Ensure that you also follow the instructions regarding the depth of the holes. - Otherwise, the product may be installed improperly causing safety issues. yyDo not clean the product with wet towels
  • LG HECTO | Additional Link - Installation Manual - Page 4
    may be added or old ones may be removed. Ez Bracket Fixed component Connection rods, Rubber 2EA packings, 6EA Fixing nuts, 2EA Guide pins, 2EA Adjustable wrench (3 mm) Spanner Plate Screw 1EA (M5 x 12 mm) Preparations Ø8 mm drill bit for concrete, leveler, tapeline, driver, tape
  • LG HECTO | Additional Link - Installation Manual - Page 5
    Laser Display set for walls made from concrete, lightweight concrete, soft fieldstone, hard fieldstone, brick or cellular blocks. yyWhen installing it on a wall not specified in this manual, make sure each fixing point withstands an uplifting load of 70 kgf (686 N) and a shearing load of 100
  • LG HECTO | Additional Link - Installation Manual - Page 6
    6 INSTALLATION Installation Procedure (Stand Type) 1 Install the guide pins at the bottom of the set. 2 Connect the connection rod to the Ez bracket main unit and place it on a table, without the fixed components, at the center of the screen. NOTE yyDo not assemble the fixed components to the unit
  • LG HECTO | Additional Link - Installation Manual - Page 7
    make it level by attaching a rubber, remove or add a plate. (To add a plate, make sure to use screws that came with the product.) 4 Place the Laser Display onto the Ez bracket by aligning the guide pins and the holes on the adjustable bracket.
  • LG HECTO | Additional Link - Installation Manual - Page 8
    tapes to the top of the table referring the sides of Laser Display so that the tapes are vertically upward. Center line Up Paper screen 390 mm Down 390 mm Guide tape Adjustable bracket Table NOTE yyThe figure above illustrates the fixed components which are not fixed yet. 6 Attach the paper
  • LG HECTO | Additional Link - Installation Manual - Page 9
    INSTALLATION 9 9 Adjust the Ez bracket by following the Laser Display screen adjustment steps to make the size of the projection screen equal to that of the paper screen. Position the projection screen, aligning it with the black line of the paper screen. (If there is a gap larger than 10 mm
  • LG HECTO | Additional Link - Installation Manual - Page 10
    with it. Position the tape about 40 mm above the paper screen. The tape is used as a reference guide to help easy screen installation. 40 mm Tape Up Ф 8 Down 11 Make holes using an 8 mm drill at specified positions and detach the paper screen. 12 Insert the anchors into the four holes. 13 Fix
  • LG HECTO | Additional Link - Installation Manual - Page 11
    the end of Ez bracket rod on the wall. (Mark the positions of the holes where the Ez brackets will be fixed.) 15 Remove the Laser Display set and Ez bracket from the table. 16 16 Position both holes of the fixed component against the marks on the wall and mark the
  • LG HECTO | Additional Link - Installation Manual - Page 12
    marked with arrows using an 8 mm drill. 18 Detach the paper screen and insert the anchors into the two holes. 19 19 Secure the fixed is not possible due to lack of marginal space while aligning an image to the screen, loosen the screws and move the fixed component slightly to the left or right.)
  • LG HECTO | Additional Link - Installation Manual - Page 13
    . CAUTION yyAlign the top of screen with the top of the tape and the left and right sides of the screen with the tape. Hang the bracket on the rings by lowering the screen carefully. If the screen is upside down, the screen will be dark and no image will be displayed. Tape Magnet Down Up
  • LG HECTO | Additional Link - Installation Manual - Page 14
    14 INSTALLATION CAUTION • If the screen is tilted when pulling it down, it may not fix to the bracket and could result in damage to the screen. 23 Move the screen in all directions to check that it is securely hung on the rings. 24 Check whether the screen stays level using a leveler.
  • LG HECTO | Additional Link - Installation Manual - Page 15
    using the formula below, locate the space steels between the wall and the rings/magnets and fix them again, and align the screen to be parallel to the wall. (0.1° → 2 mm → 1 space steel) ❶ ❷ ❸ Horizontal ❶ Horizontal ❷ 0.2 °j Move to the next hole ❸ 0.3°-0.4 °jSkip
  • LG HECTO | Additional Link - Installation Manual - Page 16
    tilted to the wall, add magnets at the bottom to make the screen parallel to the wall. If the screen does not stay level If you want to move the screen vertically or if it does not stay level, remove the screen and adjust the bracket on the back. Loosen the six screws of
  • LG HECTO | Additional Link - Installation Manual - Page 17
    the left bracket screw to a higher hole or fix the right bracket screw to a lower hole. 26 Refer to the screen adjustment steps to align the image from the Laser Display to the screen. 27 Complete fine tuning by pressing the Edge Adj button on the remote control. (Press the MENU button on the
  • LG HECTO | Additional Link - Installation Manual - Page 18
    Guide 1. Reset projection * P ress the Edge Adj button on the remote control and select Reset. (Select Settings → OPTION → Edge Adj → Reset to reset the position of the projection : Blue ? ﹀ 2. Adjust the projection to fit within the screen 1 If the projection is too large Insert the hex wrench
  • LG HECTO | Additional Link - Installation Manual - Page 19
    the hole as illustrated (left) and turn it clockwise to move the projection to the right. CAUTION yyIf you are using a paper screen, align the paper screen with the projection and reattach it to the wall rather than moving the projection to the left or right. 3. Adjust the left and right widths of
  • LG HECTO | Additional Link - Installation Manual - Page 20
    4. Adjust the horizontal line of the projection to be parallel with the width of the screen 1 To turn the projection clockwise Turn the left control panel counterclockwise and turn the right control panel clockwise. 2 To widen the left width of the projection and narrow the right width Turn the
  • LG HECTO | Additional Link - Installation Manual - Page 21
    and widen the bottom width Turn the left and right control panels counterclockwise simultaneously. A B * Length A = Length B 2 To widen the top width of the projection and narrow the bottom width Turn the left and right control panels clockwise simultaneously. A B * Length A = Length B .
  • LG HECTO | Additional Link - Installation Manual - Page 22
    to the left. 3 To move the projection to the right Insert the hex wrench into the hole as illustrated (left) and turn it clockwise to move the projection to the right. CAUTION yyIf you are using a paper screen, align the paper screen with the projection and reattach it to the wall rather than
  • LG HECTO | Additional Link - Installation Manual - Page 23
    is the same size as the screen, fine-tune the projection location using Edge Adj function * Complete fine tuning by pressing the Edge Adj button on the remote control. (Press the MENU button on the remote
  • LG HECTO | Additional Link - Installation Manual - Page 24
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Owner's Manual
Laser Display install guide
Please read the safety information carefully before using the product.
www.lg.com
P/NO : MFL67652408(1302-REV00)