LG LMHM2017ST Installation Instructions - Page 13

Awarning, Warning - templates

Get LG LMHM2017ST PDF manuals and user guides View all LG LMHM2017ST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

AWARNING To avoid risk of personal injury, electrical shock or death: • Note where electrical outlets and electrical wires are before you drill into the wall. • Locate and disconnect power to any electrical circuits that could be affected by installing this oven. WARNING To avoid risk of personal injury, electrical shock or death, cover the edge of the power supply cord hole with the power supply cord bushing. Drill The Holes in The Wall And Upper Cabinet. 1. Drill holes on the circles. If there is a stud, drill a 3/16" hole for lag screws. If there is no stud, drill a 3/4" hole for toggle screws. Make sure to use at least 1 lag screw in a stud, and 4 toggle screws in the drywall or the plaster. 2. Drill a 1/2" hole at points D,E and J on the upper cabinet template. NOTE: If the bottom of the upper cabinet is recessed 3/4" or more, you will need 2"x 2" filler blocks (not included) to provide additional support for the bolts. See Figure 26. • Mark the center of each filler block and drill a 1/2" diameter hole at the marks. , Align filler blocks over the two openings in the top of the microwave oven cabinet and attach to cabinet with masking tape. See Figure 27. 3. Cut or drill a 1 3/4" diameter hole at the area marked M. Power supply cord hole on the upper cabinet template. If the upper cabinet is metal, you will need to cover the edge of the hole with the power supply cord bushing (supplied) to prevent damage to the cord from the rough metal edge. 4. Cut out the venting areas (with the saber saw): , Roof-Vented: cut out the shaded area marked L on the upper cabinet template. - Wall-Vented: Tape the rear wall template to the rear wall, lining up with the holes previously drilled for holes A and B in the plate. Cut out the shaded area marked F on the REAR WALL TEMPLATE. , Room-Vented: go to STEP 5, INSTALL THE MOUNTING PLATE, located on page 14. 5. Complete whichever venting system you have chosen. Use caulking compound to seat the exterior wall or roof opening around the walt cap or roof cap. -13- cabinet front filler block cabinet bottom shelf t Figure 26 filler block Figure 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
AWARNING
To avoid
risk of
personal
injury,
electrical
shock
or death:
•
Note
where
electrical
outlets
and
electrical
wires
are
before
you drill
into
the
wall.
•
Locate
and disconnect
power
to
any
electrical
circuits
that
could
be
affected
by
installing
this
oven.
WARNING
To avoid
risk
of personal
injury,
electrical
shock
or death,
cover
the
edge
of
the
power
supply
cord
hole
with
the
power
supply
cord
bushing.
Drill
The
Holes
in The Wall And
Upper
Cabinet.
1. Drill holes on the circles. If there is a stud, drill a 3/16" hole for
lag screws. If there is no stud, drill a 3/4" hole for toggle
screws.
Make sure to use at least 1 lag screw
in a stud, and 4
toggle screws in the drywall or the plaster.
2. Drill a 1/2" hole at points D,E and J on the upper cabinet
template.
NOTE: If the bottom of the upper cabinet is recessed 3/4" or
more, you will need 2"x 2" filler blocks (not included) to
provide additional
support for the bolts. See Figure 26.
• Mark the center of each filler block and drill a 1/2"
diameter
hole at the marks.
, Align filler blocks over the two openings
in the top of
the microwave
oven cabinet and attach to cabinet with
masking tape. See Figure 27.
3. Cut or drill a 1 3/4" diameter
hole at the area marked M. Power
supply cord hole on the upper cabinet template.
If the upper
cabinet
is metal, you will need to cover the edge of the hole
with the power supply cord bushing (supplied)
to prevent
damage
to the cord from the rough metal edge.
4. Cut out the venting areas (with the saber saw):
,
Roof-Vented:
cut out the shaded area marked L on the
upper cabinet template.
-
Wall-Vented:
Tape the rear wall template
to the rear wall,
lining up with the holes previously
drilled for holes A and B
in the plate. Cut out the shaded area marked F on the REAR
WALL TEMPLATE.
,
Room-Vented:
go to STEP 5, INSTALL THE MOUNTING
PLATE, located on page 14.
5. Complete whichever
venting system you have chosen.
Use
caulking compound to seat the exterior wall or roof opening
around the walt cap or roof cap.
filler block
cabinet
cabinet front
bottom shelf
t
Figure 26
Figure 27
filler
block
-13-