LG MA8000ST Service Manual - Page 13

Measurement, Outer, Notes, Measuring, Warning, Avoid, Contacting, Voltage, Parts, Record, Keeping,

Page 13 highlights

MEASUREMENT WITH OUTER CASE NOTES WHENMEASURING • When=yowreplace the magnetron, measure fo microwave energy leakage before_the outer case is installed and after alt necessary-components are replaced or adjusted. SpeeiaLeare,should-ha-taken in measuring the following pcutb. (Circled area of below ing) - Around the magnetron - The waveg • WARNING • AVOID CONTACTING ANY HIGH VOLTAGE PARTS • Danotsxceed mettle deflection • Thtildbtprote:must be-namoved no faster than in sec (2.5 cm/sec) along the shaded area, otherwisea false reading may result • The test probe must be held with the g onion of the handle. A falsereading-marresultif'=the operates-handis between the handle and the probe • When testiny near a corner of the door,_Iseep the probe perpendicular to the surface making sure the probe horizontally along the ovisfesuftaeetlat.s,may prvsibly cause probe damage. RECORD KEEPING AND NOTIFICATION ALTER MEASUREMENT fter adjustment=and repair of any microwave energy interruption_or_mtorowave energy blocking device, record the measured values for future reference Also enter the information on the service invoice. • The microwave-energy leakage should not be more than 4 mW/cm.sq. after determining that all parts Are-ln good condition, functioning property and genuine replacement parts which are listed in this manual-have bPen_used_ • At least ance a year, have the electromagnetic energy eakage monitor checked for calibration by ltb -manufacturer. SPECIAL TIP s • This oven used the button head screws ASSEMBLED OVEN FULL • After all comporient'Onftluding the outerizas rare full assembled, measure for microwave energy leakage (Torx style 2) around the door viewing window, the exhaust opening and air inlet openings. -a-Men-you-NNTIOve the screws, using the •-tlitinrawave energy lealtage,must-notracco.d the voillog tamper-resistant Torx driver have a prescribed below. pin-In-head. NOTE: Leakage with the outer case removed less than 5 mW/cm.sq. Leakage for a fully assembled oven (Before the latch switch (pnmary) is interrupted) with the door in-a-slightly ope position-less than 2 mW/cm.sq. 5-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35

MEASUREMENT
WITH
OUTER
CASE
NOTES
WHEN
MEASURING
Danotsxceed
mettle
deflection
When=yowreplace
the
magnetron,
measure
fo
microwave
energy
leakage
before_the
outer
case
is
installed
and
after
alt
necessary
-
components
are
otherwisea
false
reading
may
result
replaced
or
adjusted.
SpeeiaLeare,should-ha-taken
in
measuring
the
handle.
following
pcutb.
(Circled
area
of
below
ing)
-
Around
the
magnetron
-
The
waveg
Thtildbtprote:must
be
-
namoved
no
faster
than
in
sec
(2.5
cm/sec)
along
the
shaded
area,
The
test
probe
must
be
held
with
the
g
onion
of
the
A
falsereading-marresultif=the
'
operates
-
handis
between
the
handle
and
the
probe
When
testiny
near
a
corner
of
the
door,_Iseep
the
probe
perpendicular
to
the
surface
making
sure
the
probe
ho
WARNING
AVOID
CONTACTING
ANY
rizontally
along
the
ovisfesuftaeetlats,m
.
ay
prvsibly
cause
probe
damage.
HIGH
VOLTAGE
PARTS
RECORD
KEEPING
AND
NOTIFICATION
ALTER
MEASUREMENT
fter
adjustment=and
repair
of
any
microwave
energy
interruption_or_mtorowave
energy
blocking
device,
record
the
measured
values
for
future
reference
Also
enter
the
information
on
the
service
invoice.
The
microwave
-energy
leakage
should
not
be
more
than
4
mW/cm.sq.
after
determining
that
all
parts
Are
-
ln
good
condition,
functioning
property
and
genuine
replacement
parts
which
are
listed
in
this
manual
-
have
bPen_used_
At
least
ance
a
year,
have
the
electromagnetic
energy
eakage
monitor
checked
for
calibration
by
ltb
-manufacturer.
SPECIAL
TIP
s
This
oven
used
the
button
head
screws
ASSEMBLED
OVEN
FULL
After
all
comporient‘Onftluding
the
outerizas
r
are
full
assembled,
measure
for
microwave
energy
leakage
(Torx
style
2)
around
the
door
viewing
window,
the
exhaust
opening
and
air
inlet
openings.
-a-Men-you-NNTIOve
the
screws,
using
the
•-tlitinrawave
energy
lealtage,must-notracco.d
the
voillog
tamper
-resistant
Torx
driver
have
a
prescribed
below.
pin
-In
-head.
NOTE:
Leakage
with
the
outer
case
removed
less
than
5
mW/cm.sq.
Leakage
for
a
fully
assembled
oven
(Before
the
latch
switch
(pnmary)
is
interrupted)
with
the
door
in
-a
-slightly
ope
position
-less
than
2
mW/cm.sq.
5-2