LG WM3555HWA Owners Manual - Page 11

Unpacking and Removing, Shipping Material, Connecting the Water Inlet, Hoses

Get LG WM3555HWA PDF manuals and user guides View all LG WM3555HWA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

us_main.book.book Page 11 Tuesday, October 12, 2021 1:56 PM Dimensions and Clearances F 24'' (60 cm) G 1/4'' (0.5 cm) INSTALLATION 11 • Remove the bolt assemblies (bolts and retainers) by wiggling them slightly while pulling them out. ENGLISH Unpacking and Removing Shipping Material Remove all shipping materials from the washer for proper operation and inspect it for shipping damage. CAUTION • Failure to remove shipping materials can cause excessive noise and vibration. Unpacking Shipping Material *Some models do not ship with drum support. Lift the washer off the foam base. • After removing the carton and shipping material, lift the washer off the foam base. • Make sure the plastic drum support a* comes off with the base and is not stuck to the bottom of the washer. • If you must lay the washer down to remove the carton base b, always protect the side of the washer and lay it carefully on its side. Do not lay the washer on its front or back. 2 Install the hole caps. • Locate the hole caps d included in the accessory pack or attached to the back of the washer. Install the caps in the holes left by the bolt assemblies. CAUTION • Once removed, save the bolt assemblies for future use. To prevent damage to internal components, do not transport the washer without reinstalling the shipping bolts. Failure to remove shipping bolts and retainers may cause severe vibration and noise, which can lead to permanent damage to the washer. * Removing Shipping Material 1 Remove the bolt assemblies. • Starting with the bottom two shipping bolts c , use the included wrench to fully loosen all 4 shipping bolts by turning them counterclockwise. NOTE • The power cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping bolts in place. Connecting the Water Inlet Hoses To avoid the risk of costly water damage, purchase and install new water inlet hoses when installing the washer. WARNING • Do not overtighten the hoses or cross-thread the hose fittings. Overtightening or cross-threading

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
11
INSTALLATION
ENGLISH
Unpacking and Removing
Shipping Material
Remove all shipping materials from the washer for
proper operation and inspect it for shipping
damage.
CAUTION
•
Failure to remove shipping materials can cause
excessive noise and vibration.
Unpacking Shipping Material
*Some models do not ship with drum support.
Lift the washer off the foam base.
•
After removing the carton and shipping
material, lift the washer off the foam base.
•
Make sure the plastic drum support
a
* comes
off with the base and is not stuck to the bottom
of the washer.
•
If you must lay the washer down to remove the
carton base
b
, always protect the side of the
washer and lay it carefully on its side. Do not lay
the washer on its front or back.
Removing Shipping Material
1
Remove the bolt assemblies.
•
Starting with the bottom two shipping bolts
c
, use the included wrench to fully loosen
all 4 shipping bolts by turning them
counterclockwise.
•
Remove the bolt assemblies (bolts and
retainers) by wiggling them slightly while
pulling them out.
2
Install the hole caps.
•
Locate the hole caps
d
included in the
accessory pack or attached to the back of
the washer. Install the caps in the holes left
by the bolt assemblies.
CAUTION
•
Once removed, save the bolt assemblies for
future use. To prevent damage to internal
components, do not transport the washer
without reinstalling the shipping bolts. Failure to
remove shipping bolts and retainers may cause
severe vibration and noise, which can lead to
permanent damage to the washer.
NOTE
•
The power cord is secured to the back of the
washer with a shipping bolt to help prevent
operation with shipping bolts in place.
Connecting the Water Inlet
Hoses
To avoid the risk of costly water damage, purchase
and install new water inlet hoses when installing
the washer.
WARNING
•
Do not overtighten the hoses or cross-thread the
hose fittings. Overtightening or cross-threading
F
24'' (60 cm)
G
1/4'' (0.5 cm)
Dimensions and Clearances
*
us_main.book.book
Page 11
Tuesday, October 12, 2021
1:56 PM